Aasty VIJlc gn, ödljö A dziall jajc DQ4. For the following bridge rectifier circuit, draw the output voltage waveform across theload (RL) showing the maximum value. Calculate the following:Theaveragevalue of the output voltage across the load (RL).a.b. The rms value of the output voltage across the load (RL).c. The average load current.d. The rms value of the load current.(Use constant voltage drop model for the Silicon diode)5:1110 VrmsAssignment1- (ENEL2104)Page 2

In this question we need to find a following parameters for given full wave rectifier.

Q4. For the following bridge rectifier circuit, draw the output voltage waveform across the load (RL) showing the maximum value. Calculate the following: The value of the output voltage across the load (RL). a. average b. The rms value of the output voltage across the load (RL). c. The average load current. d. The rms value of the load current. (Use constant voltage drop model for the Silicon diode) 5:1 110 Vrms

Q4. For the following bridge rectifier circuit, draw the output voltage waveform across the load (RL) showing the maximum value. Calculate the following: The value of the output voltage across the load (RL). a. average b. The rms value of the output voltage across the load (RL). c. The average load current. d. The rms value of the load current. (Use constant voltage drop model for the Silicon diode) 5:1 110 Vrms

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

S-2) a) On the bridge type full wave rectifier circuit given in the figure Plot the current paths for each of the +/- alternans. b) The waveform of the Vç output voltage is given in the graphs on the side. Draw it in the blank and calculate the peak value and indicate it in the graph. c) Calculate the effective value of the output voltage. (Vç (eff) =… ..?). Note: Diodes are not ideal. VD = 0.7V.
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
Determine the a.c. ripple voltage across the load of full wave rectifier which delivers 40 W to a load resistance of 150 ohm, and ripple factor is given as 1% A) 77.4 V B) 38.7 V C) 0.387 V D) 0.774 V
Can someone please provide a step by step solution? Thank you! The full wave rectifier in the circuit below is to deliver 0.25A and 15V (peak) to a load. The ripple is to be no larger than 0.4 V peak-to-peak. The input signal is 120 V (rms) at 60 Hz. Assume V(lambda) = 0.7 V . Determine the required turns ratio, the filter capacitance, and the diode PIV rating.
What will be the out put of the H.W.R+PMMC meters, if an average responding a.c meter of half-wave rectifier read (2.36 v), and true form factor of input waveform is (1.414), * 2.36 V 4.71 V O 1.11 V 3 V
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
A half-wave rectifier is to provide an averagevoltage of 50 V at its output.a. Draw a schematic diagram of the circuit.b. Sketch the output voltage waveshape.c. Determine the peak value of the output voltage. d. Sketch the input voltage waveshape.e. What is the rms voltage at the input?
For a half wave rectifier with efficiency (N) 40.65 % and input ac power 25mW.Compute the output dc power across the load 3kn. O a. 10.15W O b. 1.015kW O c. 1.015mW O d. 10.15mW
Be a single-phase half-wave rectifier with an RL load. The sinusoidal input voltage has a frequency of 60 Hz and the value of R = 10 ohms. What is the value of L for the current extinction angle to be 270°. Tip: use Puschlowski's abacus.
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: a) Peak AC voltage Vm of the source b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL