Q3/(a) Determine VL, IL, IZ, and IR for the network Fig. if RL =180 2 (b) Repeat part (a) if RL = 470 Q. (c) Determine the value of RL that will establish maximum power conditions for the Zener diode. (d) Determine the minimum value of RL to ensure that the Zener diode is in the "on" state. 2202 Vz = 10 V Pa"400 m W 20 V

Q3/(a) Determine VL, IL, IZ, and IR for the network Fig. if RL =180 2 (b) Repeat part (a) if RL = 470 Q. (c) Determine the value of RL that will establish maximum power conditions for the Zener diode. (d) Determine the minimum value of RL to ensure that the Zener diode is in the "on" state. 2202 Vz = 10 V Pa"400 m W 20 V

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
How is a solid-state diode tested? Explain.
Determine the state of diode for the circuit * shown and find ID, VD. Assume simplified model for the diode. 4kQ 2V Off, 0.00mA, 0.4V Off, -0.005mA, 0.0v On, 0.48mA, 0.6v On, 0.55mA, 0.7v O Option 5 www. 1k0.
For the diode circuit shown below, an IN4007 diode is used, and is connected to a variable voltage supply (VIN) that provides a maximum output voltage of 6 V. The 1N4007 diode has absolute maximum forward current rating of 1A, and can be modelled with a diode drop of 0.7 V. What is the minimum value of resistance (R1) you can use to avoid damage to the diode? Answer: Vin ww R1 O Vout
B Answer all the questions. (1) The ms value of the input voltage for a bridge network is shown in the following figure. (a) Sketch Vo and determine average output Vo for the configuration of the following figure. (b) Determine the de voltage and r.m.s voltage of output. (c) Determine the required PIV rating of each diode. (d) Does this network work as a clipper? Ideal diodes 170 V 2.2 k2 2.2 ka -170 V 2.2 ka Sketch V and K
• A Si diode at a temperature of 25°C has VD = 0.7V at Is = 10nA. The temperature is raised to 125°C. 1. Calculate ID at 25°C. 2. What is effect of rise in temperature on VD & IS 3. Calculate ID at 125°C.
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
In RL load connected (without free transition diode), single phase, uncontrolled, full wave rectifier (4 diodes), the source voltage is sinusoidal and its effective value is 44Volt, 50 Hz. The ohmic load value connected to the circuit is 10 ohms. Average value of load current calculate. (L>>R) a) 4.16 A b) 3.46 A C) 3.26A d) 4.56 A e) 3.96 A
Consider the circuit shown in the figure below with Ry=13 ko and R=9 kO. The Zener diode voltage is Vz = 3.5 V, then the currents Iz and , respectively, are equal to: R1 ww 20 V O a. 1.280 mA, 0.789 mA O b. 0.680 mA, 0.189 mA O c. 0.880 mA 0.389 mA O d. 1.080 mA, 0.589 mA
The Zener diode shown below, is specified to have Vz-20V at Izr, IzK = 0.1 mA, IzT =17 mA, and r, = 14 2. Voc = 30V. 1) Replace the Zener diode with its Model. 2) Find the current I with no Load. 3) Find Vo with no Load when VCC = 30V. 4) Find R1 Min. r30V 2000 Vz = 20V %3D 68-V zener
Select any diode from LTSpice Library. (The type of diode should either be RECTIFIER or SILICON) Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 65Hz Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.
Calculate diode forward current IF, diode voltage VF, and voltage drop across series resistor for three diode models (ideal, practical and complex). Assume diode forward resistance (dynamic resistance) r’d = 25Ω. Reverse leakage current IR = 75A with series resistance of RL = 100kΩ in reverse bias. Draw equivalent circuit diagrams of each model separately and plot corresponding I/V characteristics for each model.