Q3) An inclined rectangular gate AB (3m wide and 1.5m height), is installed to control the discharge of water. The end A is hinged. Determine the force (P) applied at the end B to open the gate.
Q: The total friction mean effective pressure of a 4-cylinder SI engine has a quadratic function with a…
A: please refer handwritten solution
Q: A shaft with a key transmits 250hp at 1650 rpm. The shaft is 2ft long and has a diameter of 4in. The…
A: Given Data
Q: 19. Which one of the following values most accurately represents the maximum power that could be…
A: 19.The pressure, P = 1.5 MPaThe temperature, T = 600 KThe mass flow rate, m = 5 kg/sThe speed, u =…
Q: In a closed rigid (unchangeable, rigid) tank, 0.5 kg of air is present at a temperature of 300 K.…
A: To find:The value of final temperature of air in tank.Given data:The value of mass of the air inside…
Q: water-filled U-tube manometer is used to measure the pressure inside a tank that contains air. The…
A: For solution refer below images.
Q: two plates each with thickness t = 16 mm are bolted together with 6-22 mndia. bolts forming alap…
A: 1.The thickness of each plate, t = 16 mmThe spacing between bolts, S1 = 40 mm, S2 = 80 mm, and S3 =…
Q: Two forces are applied to an AISI 1050 HR post BD, as indicated. Knowing that the cross section of…
A: Cross-section of the vertical part, A = 1.5 in x 2.4 inThe yield strength for AISI 1014 HR steel, Sy…
Q: The heat pump cycle shown in the figure below operates at steady state and provides energy by heat…
A:
Q: The service factor for industrial universal joint applications used in the food industry is:
A: Universal Joints:A universal joint, also known as a universal coupling or a U-joint, connects two…
Q: Air enters a continuous flow compressor at a temperature of 23°C and a pressure of 100 kPa and is…
A:
Q: 11.1 Two steel plates with S, = 50 ksi are attached by transverse-loaded fillet welds, as shown in…
A:
Q: Determine the maximum shear stress in each material. Determine the location & value of the maximum…
A: The torque acting at B and C are 6 kN.m and 3 kN.m
Q: Air at 20 °C flows with a velocity of 10 m/s along a 4 m flat plate which is maintained at uniform…
A: Given Data as below:To determine:Local heat flux
Q: Calculate the output speed and direction of gear 4. N₁ = 8 teeth n₁ = 1800 RPM CW N₂ = 24 teeth N3 =…
A: The speed of gear 1, The number of teeth on gear 1, The number of teeth on gear 2, The number of…
Q: The tension in cable AB is 900 N. What is the component of force from this tension in the positive x…
A:
Q: For the state of plane stress in the figure, (a) draw the Mohr's circle, (b) determine the principal…
A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…
Q: A probabilistic approach to address variability in mechanical properties of brittle materials can be…
A: Given:To find:Weibull modulus
Q: We wish to select a heat exchanger which will yield & = 0.75, using stainless steel fin materials.…
A: please refer handwritten solution
Q: Explain passivation by drawing hypothetical polarization curve and which parameters have effects on…
A: Passivation:Passivation refers to the process by which a metal forms a protective layer, typically…
Q: Problem 4 Determine the support reactions of the beam loaded as shown below then draw the shear and
A: GivenThe cantilever beamThe intensity of the load The length of the beam L = 5 ftFindThe support…
Q: 1a. What is “surface tension”? 1b. What is “capillarity”? 1c. What diameter of clean glass tubing…
A: To explain:1a. What is “surface tension”?1b. What is “capillarity”?1c. What diameter of clean glass…
Q: When solving Frame and Machines problems, it is important to identify any two-force members before…
A: Explanation:-A two force member is a body that has force (and only forces, no moments) acting on it…
Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7…
A: Diameter of tie rod (1) = 7 mmDiameter of pin B = 5 mmLengths:a = 670 mmb = 335 mmh = 370 mmAngle=to…
Q: The beam shown in figure has across-sectional area of 2000 mm2and depth 50mm. (40x50). The second…
A: please refer handwritten solution
Q: In a single-stage gear wheel system with an evolvent profile, the rotating (drive The number of…
A: to prevent undercutting, we need to increase the pressure angle or the helix angle.
Q: Q5:Air flows inside pipe 12 cm diameter with mass flow 1.5 kg/min. 1-Is flow laminar or turbulent?…
A:
Q: Problem 8.26 The block brake is used to stop the wheel from rotating when the wheel is subjected to…
A: M0 = 440 N-mµs = 0.6
Q: the figure, in an amusement vehicle rotating in the amusement park, the center shaft rotates at a…
A:
Q: Consider the three masses A, B and C, respectively 1 kg, 1 kg and 5 kg, connected through the system…
A: Given data :-Mass of A = 1kgMass of B = 1kgMass of C = 5kgPulleys are massless and…
Q: = Determine the magnitude of the equivalent force at point B. Take F₁ 120 lb, F3 = 70 lb, F4 = 40…
A:
Q: Find frequency and mode shape for the system shown in Fig. 5, using Stodola process. Take m= 1 kg; k…
A: Here,The mass, .The stiffness, .
Q: Question 2: The clamp is used to create vertical clamping force onto wooden work pieces. If the…
A: Draw the given diagram of clamp.
Q: As shown in the figure, a 100 W/m² heat flux is applied to one side of the slab having thickness of…
A: q" = 100 W/m2L = 10 cm = 0.1 mk = 1 W/m.Kh = 10 W/K.m2To find temperature at L = 8 cm = 0.08 m
Q: 14.14 A helical compression spring is fabricated from ASTM A229 oil-te (Figure 14.3a) and has the…
A: Note:Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…
Q: In a mine, a 100 kg boulder is transported at a velocity of VA=0.1 m/s before it slides down a chute…
A: Given:To find:velocity of boulder
Q: In the figure, one end of a uniform beam of weight 150 N is hinged to a wall; the other end is…
A:
Q: Find the Re number for a fluid with the following properties. Based on the Re number the fluid is…
A: This question is based on the concept of Reynolds number.
Q: A deep groove ball bearing with a catalog load rating Co 75.4kN is to be used for an application…
A: Given:R=99%," data-mce-style="display: inline-block; line-height: 0; text-indent: 0px; text-align:…
Q: The machine shown is used for moving heavy items such as pallets of bricks around construction…
A: The weight of the boom is;The weight of the bricks is;
Q: Determine the horizontal displacement of joint C. The length, L, of trusses AC, BC is 1,300 mm.…
A:
Q: Steam at 6 MPa and 800 oC is throttled in a valve to a pressure of 1 MPa during a steady-flow…
A:
Q: Q3:Air flows over the flat plate at velocity 0.3 m/s and ambint temperature 15 C.The plate is…
A:
Q: Q1: Air expands from a storage tank through a converging diverging nozzle having a hroat area of (70…
A: Given:The throat area is .The shock area is .The exit area is .The pressure and temperature is and…
Q: in this DYNAMIC MODELS OF HYDRAULIC SYSTEMS Obtain input-output model of the following hydraulic…
A: Given:To find:Obtain input-output model
Q: A screw jack with a 1-in. double-thread Acme screw is used to raise a load of 4000 N. A plain thrust…
A: Given data as below:diameter=1inLoad = 4000 Ncollar mean diameter = 50 mmcoefficient of friction =…
Q: Determine the distance from the bottom of the base to the mass center of the bracket casting. 3.0"…
A: The radius of the semicircle, The radius of the circle,
Q: Find the location of the stagnation point and the equation of the dividing streamline. What are the…
A:
Q: While cutting a piece of paper, a person exerts the two indicated forces on a paper cutter. Reduce…
A: The force acting at handle i.e at B, F = 15 lbThe force acting at A, P = 21 lb
Q: Determine the forces in m assume h=0.9d.
A: h= .9dTo Find:(a) Force in member AD.(b) Force in member DG.
Q: The solid circular rod has a cross-sectional area of 400 mm². It is subjected to a uniform axial…
A:
Step by step
Solved in 3 steps with 6 images
- Determine the volume of the concrete arch dam.Q1:Find the location of resultant force( F)of the water on the triangular gate and the force(P) necessary to hold the gate in the position shown in Fig.e=53 water 8 ate 5m- Hing 3m P=51.09 KN P= 61.09 KN O P= 71.09 KN O 2mThe flat surface shown is submerged vertically in water. Find the fluid force against the surface. The weight density of water is 9810 N/m³. 4 m Enter the exact answer. F = i 1m 3 m N
- A member of the truss shown in Figure Q3(b) consist of section of steel pipe. Each member has cross-sectional area of 1945 mm?. Use E =200 GPa and g = 9.81 ms². A body of mass, m = 10 kg moving with a velocity, Vo hits the truss at point A, determine the largest speed Vo that results the maximum deflection of end A equal to 1.5 mm downward.Q1) If the vertical component of the hydrostatic force on the gate BC shown in fig.1 is 1200 kN.Calculate : 1- the width of the gate 2- the horizontal component (Fu) 3- the angle at which the resultant will act (the direction of the resultant). Water 5m C 5m 4mQ2) ) If the vertical component of the hydrostatic force on the gate BC shown in fig.2 is 1200 kN .Calculate : 1- the width of the gate 2- the horizontal component (FH) 3- the angle at which the resultant will act (the direction of the resultant). Water 4m o 5m 5m Fig.2
- 3.6 m R 1m 1.2 m 2.5 m Oa 3m The banner has a density of 670 kg/m and is 6mm-thick. The pipe has the linear weight of 9N/m. Which of the following completes the force diagram? A. Foy, Foz, Moy, Moz B. Fox. Foy, F oz, Mox, Moy, Moz C. Fox, Foy, Foz, Moy, Moz D. Foy, Foz, Mox, Moy, Moz Р 1.25 m 1.5 m WOR 1.25m Wanner Fo WpQ 3.6 m Oo 2.5 m R 1 mQ2) ) If the vertical component of the hydrostatic force on the gate BC shown in fig.2 is 1200 kN .Calculate: 1- the width of the gate 2- the horizontal component (Fu) 3- the angle at which the resultant will act (the direction of the resultant). Water 4m Sm 5m Fig.2Q3) Compute the horizontal and vertical components of the water pressure acting on the face of tainter gate AB of 72° sector of radius 25 ft as shown in Fig.2.Take the width of the gate as unity. The specific weight of water = 62.4 Ib/ft³. 25ft Water C 25-ft radius 36° + 36⁰
- The figure below shows the cross-section of a tank full of water under pressure. The pressure in the tank is 19.62 kN m² and its length is 2 m in the paper. An empty cylinder lies along the length of the tank on one of its corner as shown. Find the resultant force acting on the curved surface ABC. 19.62 kNm R-1m 1.5m Tank fal of waterThe flat surface shown is submerged vertically in water. Find the fluid force against the surface. The weight density of water is 62.4lb/ft'. -8 ft 8 ft 8 ft Enter the exact answer. F = i lb(c) Determine the magnitude and location of the resultant force acting on the vertical wall shown using pressure prism concept (width = 1.0 m). What is the limitation of using this concept? Patm 1.0 m Oil (0.9) Water (1.0) 1.5 m