Q1) Consider the following prototype patterns: P1 A. Find and sketch a decision boundary for a perceptron network that will recognize these two vectors. B. Find weights and bias which will produce the decision boundary you found in part A, and sketch the network diagram. C. Calculate the network output for the following input. Is the network response (decision) reasonable? Explain. p = ]

Q1) Consider the following prototype patterns: P1 A. Find and sketch a decision boundary for a perceptron network that will recognize these two vectors. B. Find weights and bias which will produce the decision boundary you found in part A, and sketch the network diagram. C. Calculate the network output for the following input. Is the network response (decision) reasonable? Explain. p = ]

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter29: Service-entrance Calculations

Section: Chapter Questions

Problem 3R: a. What is the ampere rating of the circuits that are provided for the small-appliance loads? _____...

See similar textbooks

Similar questions

For the system shown: a. Get the equations b. Simplify and determine C/R c. Draw the signal flow diagram for this system. H3 Z3 m1 R E E1 G1 G2 G3 G4 m n H2 Z1 22 H1
Each item below describes key characteristics of a particular system (that is, a plant transfer function). For each system, describe the effect of proportional control on the stability of the closed-loop system. Specifically, 1) what can you say for small gains, and 2) what for large gains? (E.g., stable, unstable, inconclusive.) Provide a short explanation of your answers, with sketches as necessary.
Problem 3.41.3- A system is shown below in figure for this system find the transfer function relating displacements y and x and also draw relating mechanical circuit diagram. A fit) K
Q5(a) Explain the Hebbian's Law. (b) Depict a diagram of a Hebbian learning in a neural network
Question 3 of 4 Determine C/R for the block diagram given below using block diagram reduction technique, and verify your result using signal flow graph. R. H, Answer with text and/or attachments:
Find the differential equation(s) that model the system. Can it be represented by a single differential equation between Vin and Vout?
What are the application of load forecasting in neural network based methods.
6. A university wants to establish a control system model that represents the student population as an output, with the desired student population as an input. The administration determines the rate of admissions by comparing the current and desired student populations. The admissions office then uses this rate to admit students. Draw a functional block diagram showing the administration and the admis- sions office as blocks of the system. Also show the following signals: the desired student population, the actual student population, the desired student rate as determined by the administration, the actual student rate as generated by the admissions office, the dropout rate, and the net rate of influx. [Section
Calculate th value of VGs , ID , Av , Ri , Ro , and the slope of A.C.L.L?
i)Most electronic circuits in communication are used to process signals which can be in digital oranalogue form. These circuits are manned for manipulating signals towards producing a desiredresult. Generally, all signal processing circuits will engage with two main factors. Identify thesefactors and compare their role in communication. A) Electronic and OpticalB) Wireless and Free SpaceC) Analog and DigitalD) Gain and NoiseE) Noise and AttenuationF) Gain and AttenuationG) None of the above ii)Signals travel in communication channels are always exposed to the possibility of interferenceeffect that could destroy the transmitted information. The interference occurs due to the existenceof two or more frequencies. There is a component that limits specific range of frequencies andallows other range to pass through in the channel. Identify this component and explain its operationwith aid of diagram. A) ModulatorB) BasebandC) Local OscillatorD) Electrical CouplerE) Optical SwitchF) Bandpass…
Problem 1 The Figure below shows a screen shot of a signal recoded by an oscilloscope. a) What are the average and fundamental frequency for the given signal? b) If the signal is sampled with a sampling frequency of 10 Hz, sketch the sampled signal on the same chart. c) Find the average value of the sampled signal. d) Use zero-order hold to convert the sampled signal to a continuous one and sketch your result on the same chart 2. 0.5 0.4 Time (s) 0.1 0.2 0.3 0.6 0.7 0.8 0.9
Find the MPO ...