PROBLEM NO. 2: Two plates each with thickness t = 16mm are bolted together with 6-22mm diameter bolts forming a lap connection. Bolt Spacing are as follows: S₁ = 40mm, S₂ = 80mm, S3 = 100mm. Bolt diameter = 22mm. Use A36 steel. Calculate the allowable strength due to block shear only. mm S₁ S₂ - S₂ S₁

PROBLEM NO. 2: Two plates each with thickness t = 16mm are bolted together with 6-22mm diameter bolts forming a lap connection. Bolt Spacing are as follows: S₁ = 40mm, S₂ = 80mm, S3 = 100mm. Bolt diameter = 22mm. Use A36 steel. Calculate the allowable strength due to block shear only. mm S₁ S₂ - S₂ S₁

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.12.1P

See similar textbooks

Similar questions

Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
PROBLEM NO. 2: Two plates each with thickness t = 16mm are bolted together with 6-22mm diameter bolts forming a lap connection. Bolt Spacing are as follows: S₁ = 40mm, S₂ = 80mm, S3 = 100mm. Bolt diameter = 22mm. Use A36 steel. Calculate the allowable strength due to block shear only. I= 16 mm S₁ S₂ S₂ S1 40 80 80 40 18-16mm S-40 S₁-100 S-40
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
A 16 mm thick tension member is connected by two 6.25 mm spliced plates as shown. The tension member carries a service loads of dead load of 110 kN and a live load of 100 kN. 40, 80 , 40 , 40, 80 40 1625 mm 16 mm 1625 mm Fy 248 MPa Fu = 400 MPa Diam. of bolts = 16 mm Fnv = 300 MPa O Determine the nominal strength for one bolt due to shear. O Determine the nominal strength for one bolt due to bearing strength of the connection. ® Determine the number of bolts required for the connection.
Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The bolts are 3/4 in. diameter. The steel is A572 Gr. 50. Check yielding and fracture. Check Block Shear. T 3in. 73im 13in 1 3in t
QUESTION 8 3. check the capacity of the shear connection. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi effective bolt hole diameter = bolt hole + 1/16" beam properties: tw=0.295 in. Fexx=70ksi what is the shear yielding capacity of shear plate in kips? (2 decimal places)
STAGGERED CONNECTIONS: A PLATE WITH WIDTH OF 400 mm AND THICKNESS OF 12 mm IS TO BE CONNECTED TO A PLATE OF THE SAME WIDTH AND THICKNESS BY 34 mm DIAMETER BOLTS, AS SHOWN IN THE FIGURE. THE HOLES ARE 2 mm LARGER THAN THE BOLT DIAMETER. THE PLATE IS A36 STEEL WITH YIELD STRENGTH Fy = 248 MPa. ASSUME ALLOWABLE TENSILE STRESS ON NET AREA IS 0.60Fy. IT IS REQUIRED TO DETERMINE THE VALUE OF b SUCH THAT THE NET WIDTH ALONG BOLTS 1-2-3-4 IS EQUAL TO THE NET WIDTH ALONG BOLTS 1-2-4. a. CALCULATE THE VALUE OF b IN MILLIMETERS. b. CALCULATE THE VALUE OF THE NET AREA FOR TENSION IN PLATES IN SQUARE MILLIMETERS. c. CALCULATE THE VALUE OF P SO THAT THE ALLOWABLE TENSILE STRESS ON NET AREA WILL NOT BE EXCEEDED.
10 mm 20 mm The assembly above is comprised of a 10mm-diameter steel bolt, and a 20mm-diameter, 2mm-thick bronze sleeve. The bolt and sleeve are rigidly connected at each end by a washer. Assume the following properties: Epolt = 29000 ksi &bolt = 6.6-106 1°F Vbolt = 0.35 Member BC is made of bronze with the following properties: Esleeve = 15000 ksi Xsleeve =9.80-106 /°F Vsleeve = 0.35 If the assembly is heated up, which of the following statements best describes how the sleeve will be affected? The sleeve will try to expand longitudinally, but will be restricted by the bolt (because the bolt has a lower coefficient of thermal expansion). The sleeve will go into tension and the bolt will go into compression. O The sleeve will try to expand longitudinally, but will be restricted by the bolt (because the bolt has a lower coefficient of thermal expansion). Both members will go into tension. The sleeve will try to expand longitudinally, but will be restricted by the bolt (because the bolt…
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.
The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for the bolts is 100 MPa. Assume each bolt supports an equal portion of the load. Determine the required diameter of the bolts. a. 20.6 mm b. 25.2 mm c.35.7 mm d.17.8 mm choose letter of correct answer
A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.
A bolted connection shown consists of two plates 300mm x12mm connected by 4 - 22 mm diameter bolts. Edge distances = 75mm dhole for tensile and rupture = db + 3 mm dhole for bearing strength for Lc = db + 1.5 mm Fy = 248 Mpa Fu = 400 Mpa Fn = 330 Mpa Use LRFD design method. Determine the design strength due to the gross yielding of plates. (kN)