Problem 3 Water is issued steadily from a pipe to the air with a diffuser as shown below. Gravity acts downward. The friction factor for the long pipe is f-0.0175. The large tank to the pipe entrance has a minor loss coefficient of K 0.5 and the diffuser loss coefficient is K-0.2. Ignore the minor loss from the exit to the air, Find the volumetric flow rate Q. Note that the velocity in the pipe differs from the velocity at the diffuser exit. Use p=998kg / m² u=1x10³ Newton-s/m². Also the friction factor is already provided so no iteration is required! 2 m d₁ = 3 cm, L= 2 m d₂=5 cm 15 diffuser

Problem 3 Water is issued steadily from a pipe to the air with a diffuser as shown below. Gravity acts downward. The friction factor for the long pipe is f-0.0175. The large tank to the pipe entrance has a minor loss coefficient of K 0.5 and the diffuser loss coefficient is K-0.2. Ignore the minor loss from the exit to the air, Find the volumetric flow rate Q. Note that the velocity in the pipe differs from the velocity at the diffuser exit. Use p=998kg / m² u=1x10³ Newton-s/m². Also the friction factor is already provided so no iteration is required! 2 m d₁ = 3 cm, L= 2 m d₂=5 cm 15 diffuser

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows a portion of a fire protection system in which a pump draws water at 60°F(v=1.21 x10-5 m² from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height of the the water level in the tank in order to maintain 5.0 Psig pressure at point A
A horizontal 150 mm diameter pipe gradually reduces its section to 55 diameter, subsequently enlarging into 150 mm section. The pressure in the 150-mm pipe at a point just before entering the reducing section is 147 kPa and in the 55 mm section at the end of the reducer, the pressure is 79 kPa. If 657 mm of head is lost between the points where the pressure are known compute the rate of flow in L/s of water through the pipe.
points A and B are given as 29.43 N/cm2 and 22.563 N/cm respectively while the datum head at A and 266 Fluid Mechanies Problem 6.7 A pipe of diameter 400 mm carries water at a velocity of 25 m/s. The pressures c B are 28 m and 30 m. Find the loss of head between A and B.
A pump draws 24 li/s of water from the lower reservoir and lifts it to upper reservoir. The head lossfrom the inlet 150 mm pipe diameter is three times the velocity head and the head loss going to theoutlet 100mm pipe diameter is 25 times its velocity head. What is the power generated by the pump tothe system in horsepower. (Note: Velocities from the reservoir are different from the velocities of thepipe and pleaseee draw a diagram if you can thank you so much)
1.A pipe of diameter 300 m and length 3000 m is used for the transmission of power by water. The total head at the Inlet of the pipe is 400 m. Find the maximum power available at the outlet of the pipe. Take f=0.005 2. The head of water at the Inlet of a pipe of length 1500 m and diameter 400 mm is 50 m. A nozzle of diameter 80 mm at the outlet, is fitted to the pipe. Find the velocity of water at the outlet of the nozzle if f=0.01 for the pipe.
A pitot-static tube placed in the centre of a 300 mm pipe line has one orifice pointing upstream and other perpendicular to it. The mean velocity in the pipe is 0.80 of the central velocity Find the discharge through the pipe if the pressure difference between the two orifices 60 mm of water. Take the co-efficient of pitot tube as C, = 0.98.
find the diameter of pipe of length 2500m when rate of flow of water through pipe is 0.25m cube/sec and head lose due to friction is 5m . take C=50 in chezy's formula
Item#3 The oil tank for the hydraulic system of figure below is air-pressurized at 10psig. The inlet line to the pump is 10 ft below the oil level while point 3 is 2ft below pump inlet. The pump flow-rate is 30 gpm and has a power equal to0.5HP. Find the pressure at station 3if there is a 28ft head loss between station 1 and 3. OIL LEVEL SG 0.9 1.5-IN- INSIDE DIAMETER 10 FT STRAINER ELECTRIC MOTOR M 2 FT PUMP 3 Q-30 GPM
A centrifugal pump is used to pump water (1000 kg/m³) to a height of 10m, the water splashes down back into the tank. The diameter of the impeller of the pump is 145 mm, the pump speed is 2900 rpm. The equation to calculate the flow V in the valve depending on the pressure drop differential pressure (dp) in the valve isV = 4 * sqrt (dp), whereas V is in m³/h and dp in bar. Please estimate the water flow.
The figure below shows a gasoline storage tank with cross-sectional area Asub1, filled to a depth h. The space above the gasoline contains air at pressure psub0, and the gasoline flows out the bottom of the tank through a short pipe with cross-sectional area Asub2. Derive expressions for the flow speed in the pipe and the volume flow rate. Thank you!
The oil tank for the hydraulic system of figure below is air-pressurized at 10 psig. The inlet line to the pump is 10 ft below the oil level while point 3 is 2ft below pump inlet. The pump flow-rate is 30 gpm and has a power equal to 0.5 HP. Find the pressure at station 3 if there is a 28 ft head loss between station 1 and 3.
A pipe handles a flow rate of 0.002 m³/s. Find the minimum inside diameter that will provide an average fluid velocity not to exceed 6.1 m/s.