Problem 24.17A mechanical component issubjected to a mean stress of 100 N/mm and astandard deviation of 10 N/mm. The material ofthe component has a mean strength of 130 Nhmmand a standard deviation of 15 N/mm.() Find the probability of fallure for theсоmponent.(ii) If better mamufaeturing control reduces thestandard deviation of material strength to 10N/mm?, find the probability of failure.(iii) If we consider only mean values of the datain design, find out the factor of safety:

Given: Mean stress: S_=130 N/mm2σ_=100 N/mm2SSD=15 N/mm2σSD=10 N/mm2 We need to find the margin of…

Answered: Problem 24.17 A mechanical component is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The endurance limit for a material is found by rotating beam specimen test to be S,' = 52 kpsi. Using a reliability estimate of 99.9 percent, estimate the endurance limit if the material is to be placed in reversed axial loading. Table 6-4 Reliability Factors k, Corresponding to 8 Percent Standard Deviation of the Endurance Limit Reliability, % Transformation Variate z. Reliability Factor k, 50 1.000 90 1.288 0.897 95 1.645 0.868 99 2.326 0.814 99.9 3.091 0.753 99.99 3.719 0.702
The shear modulus. G. of a material can be determined by applying a torque. T, on a cylindrical material specimen and measuring the angular twist, 0. The modulus can then be calculated from: G each measured variable (L. T.t. 0, R) is 3.4%. 3LT 2 Ree where R and Lare the specimen radius and length, respectively. The relative uncertainty in What is the total relative uncertainty in G? (Provide your amwer as a percentage using two decimal places. Do not include the % symbol.) 1226
Home work for tensile test The following data was obtained from a tensile test on 135 Load (kN) Extension (mm) 16 32 56 72 95 110 132 142 140 0.2 0.4 0.7 0.9 1.5 2.5 5.0 8.5 10.0 12.0 a specimen of 10mm diameter and gauge length 60mm. Using the graph paper supplied, plot the load-extension diagram and determine: (1) The tensile strength (2) 0.1% Proof Stress (3) Young's Modulus for the specimen
The following data was obtained from a tensile test on Load (kN) 16 32 56 72 95 110 132 142 140 135 Extension (mm) 0.2 0.4 0.7 0.9 1.5 2.5 5.0 8,5 10.0 12.0 a specimen of 10mm diameter and gauge length 60mm. Using the graph paper supplied, plot the load-extension diagram and determine: (1) The tensile strength (2) 0.1% Proof Stress (3) Young's Modulus for the specimen
Asiacell 4,ll ON 76% D19:17 سؤال الواجب.docx Problem :- The following data was obtained tensile test on a specimen of 6 mm diameter and gauge length Lo=30 mm: load(KN) 0 40 80 95 90 135 150.2 145 130 120 elongation(mm) 0 0.022 0.13 0.25 0.55 2.01 3.88 4.12 5.22 6 Plot engineering and True (stress-strain) curves, then determine the (oy, ɛy), (ou, ɛu), (of, , ef), ductility , modulus of elasticity . Then select on the drawing (strain hardening (n)), (Necking), (uniform plastic region and non-uniform plastic region) and (elastic & plastic) region)?
You have been given the following set of data from a soil-geotextile friction test: Normal stress (kPa) Peak shear strength (kPa) Residual shear strength (kPa) 17 20.2 13 35 31 22 70 52 39.5 140 94 74.5 (a) Plot the Mohr-Coulomb failure envelope (x-axis=normal stress; y-axis=shear stress) (b) Determine the peak friction angle, and the residual friction angle, . (c) Determine the peak adhesion and the residual adhesion. (d) Calculate the fabric efficiency based on a soil friction angle of = 35-degrees using the peak friction angle. **HINT: the equation for efficiency of soil friction angle mobilization is:
25000 bolts are going to be used to fix a certain structure. The bolts have a mean fatigue life of 10000 days with a standard deviation of 2000 days under heavy dynamic loading conditions.What is the probability that a bolt will fail between 8250 and 12500 days of use?
Tutorial Mechanical properties 1. Based on data collected as Table 1, plot graph Stress vs strain, determine YS, TS and E. | Table 1: Data load and length for tensile test Gage length (mm) Load Gage length Load (N) (mm) (N) 35,220 35,720 40,540 50.8000 50.9778 50.8102 50.8203 4,890 51.0032 9,779 51.8160 14,670 50.8305 48,390 53.3400 19,560 24,450 27,620 29,390 32,680 33.950 34,580 50.8406 59,030 65,870 69,420 69,670 (maximum) 55.8800 50.8508 50.8610 58.4200 60.9600 50.8711 61.4680 50.9016 68,150 63.5000 50.9270 60,810 (fracture) 66.0400 (after fracture) 50.9524 Original, specimen diameter: 12.7 mm.
The following data were collected from a 12 mm diameter test specimen of Magnesium. LOAD (N) GAUEGE LENGTH (mm) 0 5000 10000 15000 20000 25000 26500 27000 26500 30.000 25000 30.0296 30.0592 30.0888 30.15 30.51 30.90 31.50 (maximum load) 32.10 32.79 (fracture) After the fracture, the gauge length is 32.61 mm and the diameter is 11.74 mm. a) What is the elastic modulus? b) Percent elongation at fracture? c) Percent elongation after fracture? d) What is the Poisson's ratio? e)Draw the engineering stress-strain diagram corresponding to the values in the table. Call this plot I. Now consider this experiment is repeated at a higher temperature with an identical sample. Draw the new engineering stress-strain diagram, call it plot II and highlight the differences (on the same graph) between I and II.
SITUATION 8 (a) The elongation of a steel bar under a particular load has been established to be normally distributed with mean of 0.05 inch and standard deviation of 0.01 inch. (a.1) Find the probability that the elongation of a steel bar is below 0.15 inch. (a.2) Find the probability that the elongation of a steel bar is between 0.025 and 0.050 inch. (b) In a certain city, the daily consumption of water (in million liters) approximately follows a gamma distribution with parameters a = 1.5 and B = 3. If the daily capacity of the city is 8 million liters, what is the probability that on any given day, the water supply is inadequate?
The shear modulus, G, of a material can be determined by applying a torque, T, on a cylindrical material specimen and measuring the angular twist, 0. The modulus can then be calculated from: G the specimen radius and length, respectively, The relative uncertainty in each measured variable (L. T, t. 0. R) is + 3.7% 3LT where R and L are %3D 2 Ree What is the total relative uncertainty in G?
Testing and Rework Bolts installed on a production line are tightened with automatic wrenches. They are to be tightened sufficiently to yield the full cross-section in order to produce the highest possible initial tension. The limiting condition is twisting off the bolt head during assembly. The bolts have a mean twisting off torque of 20 Nm with a standard deviation of 1 Nm. The automatic wrenches have a standard deviation of 1.5Nm. What mean value of torque wrench setting would result in only 1 in 500 twisting off during assembly? Give a rough estimate only. A unit has a constant failure rate of 0.3% per 1000 hours. What is its MTBF? What are the probabilities of the unit successfully completing missions of 10000, 100000 and 1000000 hours? Give a rough estimate only. Please provide an in depth answer for the above questions, thank you so much!

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Problem 24.17 A mechanical component is subjected to a mean stress of 100 N/mm and a standard deviation of 10 N/mm. The material of the component has a mean strengih of 130 Nmm and a standard deviation of 15 N/mm?. 1) Find the probability of failure for the сотроnent.