Answer using Bond development length hooks and splicing of reinforcement in RCD NSCP 2015. The answer is A) 1257mmB)Ld=866.614mmI need a complete solutions with step by step.. PROBLEM 10.2:A 3m wide wall footing supports a 300mm wall. It is reinforced with 20mmo bars with concretecovering of 75mm. If f = 20.7 MPa and fy = 414 MPa,a.b.Which of the following gives the available space for development.Which of the following gives the required development length.Ans: 1275 mmAns: La = 866.614 mm

Answered: Image /qna-images/answer/6d597ae7-8c0a-483f-a21d-a582577c4e10.jpg

PROBLEM 10.2: A 3m wide wall footing supports a 300mm wall. It is reinforced with 20mm bars with concrete covering of 75mm. If f = 20.7 MPa and fy = 414 MPa, a. b. Which of the following gives the available space for development. Which of the following gives the required development length. Ans: La Ans: 1275 mm 866.614 mm

PROBLEM 10.2: A 3m wide wall footing supports a 300mm wall. It is reinforced with 20mm bars with concrete covering of 75mm. If f = 20.7 MPa and fy = 414 MPa, a. b. Which of the following gives the available space for development. Which of the following gives the required development length. Ans: La Ans: 1275 mm 866.614 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam, which is rectangular, has a base of 250 mm, and d = 575 mm. The beam is singly reinforced, where the recorded strain in the steel is 0.005, and the strain in the concrete is 0.003. fc' = 20.7 MPa, fy = 414.6 MPa. Note: As is not Given %3D b) Determine the value of "As" O 1856.000 sq. mm O 2133.636 sq. mm 1944.545 sq. mm O 2029.091 sq. mm O None of the Choices O 2198.181 sq. mm
A prestressed beam has a cross section of 250 mm x 500 mm and has a simple span of 6 m. The tendons are placed 70 mm above the bottom of the beam. The wires used are stress relieved tendons with fpu= 1350 MPa and fpe= 760 MPa, fc'=35 MPa. The prestressed beam is not to be grouted after application of the prestress. Aps= 1000 sq. mm Compute the stress in prestressed reinforcement at nominal strength. Compute the ultimate moment capacity of the prestressed beam. Compute the safe live load that the prestressed beam could carry.
Given: Slab thickness, t= 175mm Effective depth, d = 300 mm Web width, b = 250 mm Materials: Concrete, fe' = 24 MPa Steel bar, fy415 MPa $=0.90 Concrete slab casted monolithically with the beam. The steel bars will be distributed in one layer only. 1. If the equivalent width of the concrete flange from the slab b = 600mm, determine the value of the balanced steel area of the section
A footing supports a 300 mm thick concrete wall. Wall dead load = 180 kN/m Factored load combination = 1.2D+1.6L Width of footing=1.75 m Thickness of footing = 300 mm Effective cover of centroid reinforcement = 100mm Wall live load=90 kN/m Concrete Strength, fc=21MPA Steel Strength, fy-415 MPa Unit Weight of Concrete = 24 kN/m^3 a) Which of the following gives the required spacing of 16 mm diameter bars due to the moment at the footing? b) Find the wide-beam nominal shear stress. c) The allowable soil pressure is 96 kPa. What should be the width of the footing so that the allowable soil pressure will not be exceeded? Assuming footing thickness of 250 mm.
Given the following properties of a rectangular concrete beam: b = 300mm, d = 425mm, f'c = 28 MPa, fy = 415 MPa. The beam is reinforced for tension only. when the beam is reinforced with four 25mm diameter bars. Determine the actual stress of the steel A 1299.30MPA B 1429.23MPA 1572.15MPA D) 1209.25MPA
Problem 4.39 Design the one-way slab shown in the accompanying figure to support a live load of 10 kN/m2. Do not use the ACI thickness limitation for deflections. Assume concrete weighs 23.5 kN/m.f 28 MPa and f, = 420 MPa. Use p = Pmur: (One ans. 240-mm slab with #25 @ 140-mm main steel) -10m Width of the slab is 10m WL = 10kN/m2 And draw slab section showing all reinforcements along with the slab
Show your complete solution with cancellation of units, and NO SHORTCUTS. 2.A timber block 250 mm square is reinforced on each side by a steel plate 250 mm wide and t mm thick. Determine the thickness t so that the assembly will support an axial load of 1200 kN without exceeding a maximum timber stress of 8 Mpa or a maximum steel stress of 140 Mpa. For timber, E = 10 x 103 Mpa; for steel, E = 200 x 103 Mpa.
29 A square footing 2.2 m x 0.39 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 317 kN LL = 217 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal one way shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
30 A rectangular footing 2.3 m x 3.6 m x 0.38 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 306 kN LL = 241 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
2nd: A simply supported 14-m span beam, 300-mm wide by 540-mm deep, is pre- stressed by straight tendons with Aps = 774 mm² located 70 mm from the bottom at an initial prestress of 1.10 GPa. Calculate the concrete stress in MPa at the bottom fiber of the beam at midspan immediately after the tendons are cut. Write your answer in 2 decimal places only. Use unit weight of concrete 24 kN/cu.m. Sign convention is (+) tension, (-) compression. Indicate the sign in your final answer.
Design a monolithic concrete slab indicated below. The floor slab is to carry a service live load of 2.7KPA uniformly distributed over its surface and service deadloads of 1.1KPa for floor finish and 0.72KPa for ceiling. Use fc = 21MPA, fy = 276 MPa, Unit weight of Conc = 23.54KN/m³. Sketch the reinforcement detail. -4.5000+3.0000-4.0000- -4.5000- 5.2000 SLAB 1 6.4000 7.0000 3.0000
Strength of Materials 5.4 Assuming a density of 120 #/ft.3 for masonry brick- work, determine the maximum height of a brick wall if the allowable compressive stress is limited to 150 #/in.² and the brick is (a) four inches wide and (b) six inches wide. 14 www WISS AK 4 THICK BRICK MASONRY WALL 263