NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A roof truss is shown. Take the load P = 1.7 kN. 6 m 6 m 6 m P P 2.4 kN 2.4 kN B D 7.5 m 9 m 9 m E Determine the force in each member of the roof truss shown. State whether each member is in tension (T) or compression (C). The force in member DF (FDF) is | KN (Click to select) The force in member EF (FEF) is KN (Click to select) The force in member AB (FAB) is KN (Click to select) The force in member AC (FAC) is KN (Click to select) The force in member BC (FBC) is KN (Click to select) The force in member BD (FBD) is KN (Click to select) The force in member CD (FCD) is KN (Click to select) The force in member CE (FCE) is The force in member DE (FDE) is KN (Click to select) KN (Click to select)

NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A roof truss is shown. Take the load P = 1.7 kN. 6 m 6 m 6 m P P 2.4 kN 2.4 kN B D 7.5 m 9 m 9 m E Determine the force in each member of the roof truss shown. State whether each member is in tension (T) or compression (C). The force in member DF (FDF) is | KN (Click to select) The force in member EF (FEF) is KN (Click to select) The force in member AB (FAB) is KN (Click to select) The force in member AC (FAC) is KN (Click to select) The force in member BC (FBC) is KN (Click to select) The force in member BD (FBD) is KN (Click to select) The force in member CD (FCD) is KN (Click to select) The force in member CE (FCE) is The force in member DE (FDE) is KN (Click to select) KN (Click to select)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 1 A truss is subjected to the loadings as shown in the figure. Determine the force at member JI, IC, CD, and DI. Use combined solution using Method of Section and Method of Joints. State wether the force is Tension or Compression. USE 3 DECIMAL ONLY. 10 m, 5 @ 2 m 3 kN 6 kN 4 kN 3 kN 1.5 kN K Jooo o foo 00 F 5 m 9 kN B A Figure 1.0
At joint D, a truss is used to sustain loads of P = 600 N and P2 = 1300 N, as shown in Figure A. No member of the truss can be subjected to a force more than 3000 N in tension or 3500 N in compression, according to the design standard. Determine whether or not the truss will fail.
Determine the maximum magnitude of load P that can be applied to the truss. The maximum allowable tensile force in the members of the truss is (Ft) max = 5.2 kN, and the maximum allowable compressive force is (Fe) max = 3 kN. Take d = 2 m. (Figure 1) Figure 1 of 1 E d/2 C PV d/2 <
The truss shown in Figure 1 is constructed such that members AB and BC are of equal length. Additionally, joint A and joint C are pin supported, and an external load of magnitude 12kN is applied vertically at joint B.Each truss member has a cross-sectional area of 200 mm² and an elastic modulus of 200 GPa. Draw an equivalent problem by replacing the pin support at joint C with a roller support and introducing a pronumeral force.Using Castigliano’s second theorem, determine the magnitude of horizontal support reaction at joint C. AC = 4m and BC =3m
The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be applied so that the stresses will not exceed 100 MPa in tension or 70 MPa in compression. See figure 101. Figure 101 A 0 2m P B 2.5m 1.5m C
For the truss shown, determine the safe value of P if the allowable stress in tension is 146 MPa in tension and 92 MPa in compression. The cross-sectional area of vertical and horizontal members is 1260 mm2 while that of diagonal members is 862 mm2 .
In this figure, what is the force at member AD in kN?
A structural beam subjected to sagging bending has a cross section which is an unsymmetrical I section. The overall depth of the beam is 300 mm. The flange stresses are O top = 200 N/mm² - = - Obottom 50 N/mm² What is the height in mm of the neutral axis above the bottom flange?
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the given structure with P= 1250 N. Bo 400 mm-500 mm The force in member BA is Using the method of joints, determine the force in each member of the truss shown. State whether each member is in tension (7) or compression (C). The force in member BC is A The force in member CA is 375 mm N (Click to select) ✓ N (Click to select) ✓ N (Click to select) ✓
a) What is a truss? Explain shortly in your own words, and illustrate with one example. b) For the truss in the figure below, determine the zero-force members and give a short explanation to support your answer. B C D A H G F -1.5 m-1.5 m 1.5 m-1.5 m- 2 m 2 m E-
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Warren bridge truss is shown. Take P = 9 kips. 9 ft 9 ft A B 18 ft- -18 ft с P D 18 ft 18 ft E -18 ft- 12 ft GI Draw the free-body diagram of the Warren bridge truss, joint A, joint B, and joint C. (You must provide an answer before moving on to the next part.)
The rigid beam is supported by three suspender bars. Bars AB and EF are made of aluminum (Eal = 70 GPa) and bar CD is made of steel (Est = 200 GPa). If each bar has a cross-sectional area of 450 mm² and P = 50 kN, determine the following for each bar: a) Stresses (in MPa) b) Elongation (in mm) al B st D al 0.75 m 0.75 m 0.75 m 0.75 m 2P F 2 m E