Modulus of elasticity and Poisson's ratio of a material are 2-1 x 105 N/mm? and 0-25 12. respectively. What is the value of modulus of rigidity of the same material in N/mm2 ? (a) 0-84 (b) 0-70 (c) 1.40 (d) 0-50

Modulus of elasticity and Poisson's ratio of a material are 2-1 x 105 N/mm? and 0-25 12. respectively. What is the value of modulus of rigidity of the same material in N/mm2 ? (a) 0-84 (b) 0-70 (c) 1.40 (d) 0-50

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Related questions

Q: tailgate with c.g. G1. Determine the tension in the two restraining cables, one of which is shown (A...

A: Given -

Q: In the frame, shown, members 'ACE' and 'BCD' are connected by a pin at 'C' and by the link 'DE'. For...

A: To find Force in link ‘DE’ in N. Horizontal component at ‘C’ on member ‘BCD’ in N

Q: 3. A 6 m long simply-supported beam is pre-stressed as shown in the figure : Neutral axis I50 mm Pre...

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 14...

A: Determine the normal stresses in bronze rods (1) and steel rod (2)

Q: On a map drawn to a scale of 1:5000, contour lines are 6 mm apart at a certain place. The contour in...

Q: Problem: Analyze the given frame by the slope-deflection method. Determine the end moments and the s...

Q: Select the lightest W section to carry an axial compression load of 60 kips dead load and 250 kips l...

A: We will solve this question in step no. 2

Q: Measurements show that the wavelength of a sound wave in a certain material is 18 cm. The frequency ...

A: This question is related to the Earthquake Engineering. In this question we calculate the velocity o...

Q: Rework Prob. 8-12, considering the y axis. Prob. 8-12 Find the values of S and Z and the shape fac...

A: To Find - Find the values of S and Z and the shape factor about the horizontal x axes.

Q: Problem 3.7 (Ans. ØM„ = 379.1 ft-k) 24 in. 27 in. 4 #9 bars 3 in. fy = 60,000 psi f:= 4,000 psi %3D ...

A: Find design moment

Q: A steel wire 16m long with a radius of 3.6mm is observed to stretch 62mm when a tensile force is app...

Q: In a cantilever beam of length 2 m, the shear force (in N) is given by V(x) = 5x², where x is the di...

Q: Determine the force and couple moment reactions exerted by the nut and bolt on the loaded bracket ma...

A: Given -

Q: Determine the force in the member CE of the truss shown. It has F1=13 and F2-3 loaded as shown. Answ...

Q: Oil (sg=0.87) flows from A to E as shown. The head loss is assumed to be as follows: A to B = 0.45 %...

Q: A tubular post of outer diameter d, is guyed by two cables fitted with turnbuckles (see figure). The...

Q: How important is knowing the existence of groundwater in civil engineering? Cite on why groundwater...

A: Importance of ground water in civil engineering. Why do we need to study various aspects of ground ...

Q: A cylindrical chamber is filled with an elastic material of modulus E and Poisson's ratio µ, as show...

A: Given data,

Q: Consider the beam with loading as shown in the figure below. The deflection of the a w̟lª b beam at ...

Q: 1. Using both LRFD and ASD methods, and disregarding the moment amplifications, determine if the mem...

Q: A 54 kg crate with c.g. G2 rests on the 27 kg pickup tailgate with c.g. G1. Determine the tension in...

Q: Determine the pressure head at point 1 and point 2 (in meters). Also, determine the power delivered ...

Q: A shell of diameter = 700 mm %3D Height of the shell= 100 mm Height with corner radius=D0.9 mm It is...

Q: What does material engineers do?

A: Materials engineers assess materials and develop machinery and methods for the production of materia...

Q: Using Unified Soil Classification System, determine the type of soil, the coefficient of gradation a...

A: To Find :- Type of Soil Coefficient of gradation Group symbol Given Passing no 4 = 47% Passing no 20...

Q: A reservoir with average surface spread of 4.8 km2 in the first week of October has the water surfac...

Q: A vertical pole, cantilevered at the bottom has a solid circular cross-section of diameter, d= 49.21...

Q: 1. For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the...

Q: A bearing wall for a building is to be located close to a slope. The soil has a unit weight of 15.02...

A: Slope stability is the process of calculating and assessing how much stress a particular slope can m...

Q: 30. An equipment has a first cost of P500000, and the cost of installation is P30000. If the salvage...

Q: Select the lightest W section to serve as an axially loaded column 28 ft long, in a braced frame, wi...

A: We have to determine the W section to serve as an axially loaded column 28 ft long as per the A992 a...

Q: The van travels over the hill described by y=(-1.5x10 )x²+15) ft. If it has a constant speed of 78 f...

Q: A symmetrical parabolic curve passes through point A whose elevation is 23.23m at a distance of 54 m...

A: The given values are as follows,The elevation from PC=23.33mThe Distance from PC=54mThe elevation of...

Q: Determine the maximum bending moment for the beam shown below. Usea = 8 ft, b = 12 ft, c= 6 ft, and ...

Q: A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure). Th...

A: Given data, Ultimate strength of cast iron in compression = 50 ksi FOS = 3.5 Outer dia of pier = 4.5...

Q: An observer notes that an approach to a pretimed signal has a maximum of eight vehicles in a queue i...

A: We have to determine the value of time that will observer take to this queue to clear after the star...

Q: An orifice has a coefficient of discharge of 0.62 and a coefficient of contracion of 0 63 Determine ...

Q: the farm water requirement is 18.73 mm/day, the water duty in lps/ha is Answer:

Q: H.W.1/Start from : = Kz (1). BOD (1) = Lo - z (1) = Lo(1 – e-Ki'). To obtained :

Q: onsano Acomposite assembly consisting of a steel [G- 80 GPa] core (2) connected by rigid plates at t...

Q: The beam shown below is loaded with a concentrated clockwise moment of 80 kN-m at point B. The corre...

Q: total Average Day Demand in a Development is 52,000gals, Determine the required volume of water tank...

A: Given Average demand per day 52,000 gallons Additional requirements 20% Fire demand 350pgm for 30 ...

Q: 1. For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the...

Q: If the pressure at a point in the ocean is 79 kPa, what is the pressure 25 meters below this point? ...

Q: The state of plane strain at a point is ɛ = 800 x 10-6, ɛ, = 200 x 10-6 and y. = -600 x 10-6. If mat...

A: Given data, E=200 GPa μ=0.30 to find the major principal stress

Q: 1. A tangent distance of a 4 deg simple curve is one fourth (4) to its radius. Sketch and a) Compute...

A: As per authoring guidelines, if the question number is not specified, the first question or three su...

Q: ..--. A stream of 150 litres per second was delivered from a canal and 110 litres per second were de...

A: To find the following water conveyance efficiency water application efficiency water storage effic...

Q: Two polymer bars are connected to a rigid plate at 8, as shown. Bar (1) has a cross-sectional area o...

A: Given data: A1 = Cross sectional area of Bar 1 = 1.71 in2 A2 = Cross sectional Area of Bar 2 = 1.019...

Q: An unsteady velocity field is given by u = t2+ 3y and v = 4t + 5x. Acceleration at the point P(2, 2)...

Q: -- A water course commands an irrigated area 1000 hectares. The intensity of irrigation of rice in t...

Concept explainers

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.

Question

Modulus of elasticity and Poisson's ratio of
a material are 2:1 x 105 N/mm? and 0-25
12.
respectively. What is the value of modulus
of rigidity of the same material in N/mm2 ?
(a)
0-84
(b)
0.70
(c)
1.40
(d) 0-50

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A compound bar consists of (4) aluminum alloy bars of (2mm) diameter and (2) steel bars of (3mm) diameter. Determine the followings: 1- The stresses in each material when a compressive force of 70 kN is applied on the compound bar and the temperature is changed from 20 °C to 40 °C. 2- The compound modulus of elasticity (Ec). Knowing that : E=200GN/m² E=70 GN/m² and a=11×10% per °C and a=22×10 per °C for Steel for Aluminum Alloy
The sectional dimension of a reinforced concrete short column is b X h= 400 mm X 400 mm. The length of the column is 2 m. 4 25 longitudinal steel bars are arranged in the column. The mechanical properties of the materials are f. = 19 N/ mm², E, = 2.55× 10* N/ mm², f'y = 360 N/ mm², E, = 2.0× 10 N/ mm?. (1) The ultimate compressive capacity of the column. (2) The compressive deformation and the compressive forces resisted by the concrete and the steel, respectively, when an axial compression N=1200kN is applied on the column. (3) The compressive forces resisted by the concrete and the steel, respectively, after the column has been in service for several years under the constant compression of N=1200kN with a creep strain of Ee-0.001.
y 400 mm 4 mm B 200 mm A 6 mm The rectangular plate is subjected to the deformation shown by the dashed line. Determine the average shear stress in the plate if the shear modulus of the material is 2 MPa. Express your answer in kPa and round it to the nearest integer if necessary.
A rigid slab weighing 600 ku is placed upon two ·bronze rods and one steel rod each of 6000 mm² area at a temperature of 15¢ as shown, find the temperature at which the stress in steel rod will be Zero? take: Coefficient of expansion for steel = 12 um/m. c coefficient of expansion for bronze = 18 um/m. c Young's modulus for steel = 200 G Va Young's modulus for bronze = 80 GPa 600 IN 250mm 300mm -bronze -Steel
500 MPa b 0.006 120 KN 100 mm b) Determine the rod's new length under this load c) Determine the rod's new diameter under this load 20 mm 120 kN A rod 100 mm long with a diameter of 20 mm is subject to 120 kN of tension as shown, alongside with the stress-strain curve of its material. Assume a Poisson's ratio of 0.35. a) For the given load condition, is the rod behaving elastically or plastically? Explain your reasoning The tensile load is now removed, and the ends are now subject to a shear force of 10 KN in the same plane as the cross-section (i.e., the force is acting "horizontally"). Assume elastic behavior. d) Determine the shear strain resulting from this shear force (ignoring any bending effects) e) What is the horizontal displacement of one end of the rod relative to the other end under this shear force?
2. Shown below are pieces of unsaid material. They are combined and locked in each other and a force P is pulling each side. Assuming that the Shear stress for the material is 38 MPa, Determine the force P needed to fracture the materials in shear. 30 mm 30 mm 80 mm Section A-A
A vinyl [E = 2.65 GPa; v = 0.41] block with width b = 60 mm, depth d = 120 mm, and height h = 320 mm rests on a smooth rigid base. A load P is applied to a rigid plate that rests on top of the block. Calculate the change in the depth dimension d of the block after a load of P= 180 kN is applied. Rigid plate Answer: Ad = i Width b P Depth d Height h Rigid base mm
1500 KN 800 mm 70 mm 100 mm 1500 KN A bar has a length of 800 mm, width 100 mm, and thickness 70 mm, and is being subjected to 1500 KN of tension as shown. As a result, the length of the bar as increased to 802.5 mm and its width has decreased to 99.906 mm. Assume elastic behavior. a) Determine the Young's modulus (E) of the material b) Determine the Poisson's ratio (v) of the material c) Determine the Shear modulus (G) of the material d) Determine the new thickness of the bar in mm e) Determine the percentage change in the total volume of the bar
Steel cylinder has 200 mm mean diameter with a wall 1 mm thick and 310 mm long. Determine the circumferential and longitudinal stresses that occur on the cylinder if the maximum pressure difference allowed between the inside and outside must not exceed 100 MPa. Determine the effects of three dimensional loading by determine volumetric strain and change in volume for the first steel cylinder. Modulus of elasticity E= (210 GPa), Poisson's ratio 0.30. 7
* Your answer is incorrect. A solid plastic rod has a diameter of d = 21 mm and a length of L = 600 mm. An axial load of P = 24 kN is applied to the rod as shown. The elastic modulus is E = 2.6 GPa and Poisson's ratio for this material is v= 0.37. Determine the magnitude of the change in the rod diameter Ad for the given load. Answer: Ad= i -0.21 L mm
Problem: A steel rod with a cross-sectional area of 180 mm2² is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 106 mm/ (mm°C) and E= 200 GPa. a. What is the temperature at which the stress will be zero? b. What is tthe temperature at which the compressive stress will be 48 MPa?
(a) 128.5 GPa circular rod of diameter 30 mm and length 200 mm is subjected to a tensile force. The axtension of rod is 0.09 mm and change in diameter is 0.0045 mm. What is the Poisson's ratio of the material of the rod? (a) 0.35 (b) 0.33 (c) 0.32 (d) 0.30