Set P1= 6.3kN, P2= 8kNplease help with part A,B,C,D,E,F,GSet P = 6.3 kN, P2 = 8 kN. (Figure 1)Figure(<1 of 1E6 m4 m4 m4 mP2 Part ADetermine the force in the member AB and state if the member is in tension or compression.Express your answer to three significant figures and include the appropriate units. Enter negative value in tiof compression and positive value in the case of tension.HAFAB=ValueUnitsSubmitRequest AnswerPart BDetermine the force in the member AE, and state if the member is in tension or compression.Express your answer to three significant figures and include the appropriate units. Enter negative value in thof compression and positive value in the case of tension.FAE=ValueUnitsP PearsonPart CDetermine the force in the member BC and state if the member is in tension or compression.Express your answer to three significant figures and include the appropriate units. Enter neof compression and positive value in the case of tension.HA?FBC =ValueUnitsSubmitRequest Answer

Answered: Image /qna-images/answer/9f5a3959-b658-4af9-ad22-76deaa26fab3.jpg

Answered: < 1 of 1 Figure E 6 m D 4 m 4 m 4 m Pi…

Engineering

Mechanical Engineering

< 1 of 1 Figure E 6 m D 4 m 4 m 4 m Pi P2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure below shows a four-bar linkage (non-scaled diagram) at an instant. The input angle is equal to the output angle (02 - 04) and the transmission angle is 30°. The input link is extended beyond joint B and an input force (Fin) is applied at the end of it, while an output force is drawn from the midpoint of the output link. If an output force of 30 N is desired from an input force of 10 N, how far the input link should be extended, i.e., what is the distance from point B to the point where Fin is applied. Fin B out undefined 02 04 A. Non-scaled diagram; AB = 10, CD=r4 = 30 (output), all in mm
QUESTION 6 Select the type of this mechanism below: L2 02 L3 А L1 C L4 O Crank-rocker O Triple rocker O Crank-crank O Slider-crank
need help with problem 4-22 please
Problem 4: For the following mechanism, (a) Find all instant centers ( (b) Find the mechanical advantage (MA) of the mechanism Drawing is to-scale. TMM 1 Fin 2 MM THIM 1 Fout
Design a 4-bar linkage to carry the body in Figure 1 through the two positions P1 and P2 at the angles shown in the figure. Use analytical synthesis with the free choice values z = 1.075, p = 210°, B-27° for left side and s = 1.24, w= 74°, 2=-40° for right side. Y 1.236 P2 147.5° 210° 2.138 Py Figure 1 X
Figure Q2-2 shows a schematic of a retractable landing gear of aircraft. The retraction mechanism is a 4 bar linkage (O1ABO2), which is actuated by a hydraulic cylinder and piston, D, pivoted at E with a joint at C to link O,A. Hydraulic cylinder & piston D Joint for landing gear wheel Figure Q2-2 Use the Gruebler's equation of DoF (Degrees of Freedom) of a linkage mechanism to assess if the landing gear produces the required retraction motion. 0,02 may be considered as the ground link. i) Hint: The joint of the wheel is not part of the linkage mechanism. The number of DoF may be used to check if it is a linkage with certain motions or a fixed structure. ii) The dimensions of the 4 bar linkage (O1ABO2) are measured as O102 = 800 mm, O1A = 780 mm, AB = 200 mm and O2B = 400 mm. Use Grashof condition to determine the specific type of this linkage. You may find the Gruebler's equation useful: M = 3(L – 1) – 2J where, M is degree of freedom (DoF) L is number of links J is number of joints
The lengths of various links of a mechanism, as shown in Figure 2, are: OA = 0.3 m; AB = 1 m; CD = 0.8 m; and AC = CB. A 45° В Figure 2: Slider cranck mechanism Draw the displacemt diagram to a scale.
2) Block 4 slides in a slot in the fixed piece 1. Axis Q₂ of crank 2 is fixed on 1. Q₂₂A = 1 1/2 in., and AB = 4/1/2 Draw the mechanism, assuming limen- sions for 1, if desired, or use center lines only. Draw the four-bar linkage for this mechanism, properly rotate the linkage Q₂ ABQ400; Name each link, and show the finite and infinite cranks. Frind graphically the two extreme positions of 13, The axis of the pin by which link 3 is attached to the block 4.. Dimension the length of the stroke of B. Ans. 3& in. for scale 1:1
Shift weight A so the lever would balance at 7/8 of the total length of the board measured from left to right. Datum -80 in 80 in A=100 Ibs B=100 Ibs C=100 Ibs
Example Problem 4-1, (page 141). [Ref.1]: The shaft shown in Figure 4-7 is supported by two bearings and carries two V-belt sheaves. The tensions in the belts exert horizontal forces on the shaft, tending to bend it in the X-Z plane. Sheave B exerts a clockwise torque on the shaft when viewed toward the origin of the coordinate system along the X-axis. Sheave C exerts an equal but opposite torque on the shaft. For the loading condition shown, determine the principal stresses and the maximum shear stress on element K on the front surface of the shaft (on the positive Z-side) just to the right of sheave B, Follow the general procedure for analyzing combined stresses given in this section. Page 2 of 8 100 mm 100 mm 50 mm Stress T B element. T. 50 mm 100 mm в 100 mm C D Shaft dia. = 32 mm FB=2440 N Fc=1220 N RD T= Torque = 120 N.m (b) Forces acting on shaft at B and C caused by belt drives (a) Pictorial view of shaft
An eyebolt is subjected to four forces as shown in figure. F_{1} = 12kN F_{2} = 8kN F_{3} = 18kN , F_{4} = 4kN that act at angles of alpha_{1} = 45 deg , alpha_{1} = 45 deg alpha_{2} = 100 deg alpha_{3} = 205 deg alpha_{4} = 270 deg Determine the magnitude and direction of the resultant force
Problem 4. For the belt drive shown below calculate the contact angle 0, if: D %3D 100 mт; d 3 30 тm; C = 300 mm. D-d 20 sin V4c² - (D – d)²- -1 D-d sin 20 Op