Lecture: Combinational Circuits Implement the given Boolean function using inverted decoder. Minimize the number of inputs in the external gates. F(x, y, z) = (0,1,5,6,7) Final answer must be in labeled logic diagram.
Q: 9. In a circuit with a 12 volt supply and 40 resistance, the power consumed is watts.
A: Given data, Supply voltage V = 12 V. Resistance R=4 Ω.
Q: 2. Which type of multiplexing can not be used for Analog signalling? a) FDM b) TDM c) WDM d) None 3.…
A: The given problem is from communication system. The detailed solution is given in the next step
Q: 20hm 2V 4ohm lohm -6V
A: We need to find out the current for given circuit by using of krichoff's law .
Q: Simplify the Boolean expression F = C(B + C)(A + B + C). (Essay)
A:
Q: Q6 Figure Q6 shows a closed loop control system of a servo motor. Assuming that the input…
A: The given figure of the closed-loop control system is shown below. We need to describe the…
Q: Explain the breakdown phenomena with respect to influence of nearby earthed objects, humidity and…
A: We have to explain the breakdown phenomena with respect to influence of nearby earthed objects,…
Q: Series-connected 10-pF and 60-pF capacitors are placed in parallel with series-connected 30-pF and…
A: Let C1 and C2 be capacitance connected in series /parallel then equivalent capacitance Cseries=c1…
Q: COMMON TRIGGERING COMPONENTS, USED FOR START UP, CONDUCT ANOTHER SEMI CONDUCTOR COMPONENTS
A: Types of semiconductors devices / switches Uncontrolled semiconductors ( Diode) Semicontrolled…
Q: Question One A dynamic system is represented by the following transfer function representation: 2.5s…
A: Given: In this question, the given details are, A dynamic system is represented by the following…
Q: Find the expression for the voltage v(t) and current i(t) of both t capacitor and the inductor as a…
A:
Q: The Voltage across PS- and PS+ equals 17.0 volts. The T/C temperature = 103 degrees Fahrenheit.…
A:
Q: (6) A 250 MVA, 25 kV, 3 phase synchronous generator has a synchronous reactance X, of 1.6 pu. It is…
A: Given: A 250 MVA, 25 kV, 3 phase synchronous generator has a synchronous reactance Xs of 1.6 pu. And…
Q: 9) Find the reactance and the impedance of the circuit. Calculate the current and the resonance…
A:
Q: Solve with complete solutions and units using 3 decimal digits: V=25 V > R3 = 80 ohm R1 = 100 ohm…
A:
Q: M₁ Vino M Rs VDD M₂ o Vout • Vo
A:
Q: Problem 10.073 - Input impedance of an Op Amp If the input impedance is defined as Zin = Vs/ls, find…
A:
Q: If the current through a 10-mH inductor increases from zero to 2 A, how much energy is stored in the…
A:
Q: Problem 10.040 - Superposition when sources have different frequencies Find the output current io in…
A:
Q: An electric motor can be modeled as a series combination of a 17- resistor and 200-mH inductor. If a…
A: The given problem is from circuits. The detailed solution is given in the next step
Q: Minimize the logic function Y(A,B,C,D) = ∑(0,1,2,3,5,7,8,9,11,14) . Use Karnaugh map. Draw logic…
A:
Q: FT rect (3-5 rect (3-5) 2 e-2 u(t) * 2 Cos Find the convolution (2t-3 (2t - 1)
A:
Q: For R1=202, R2=430, R3-185, R4-480, R5=455, R6-170, V1-8 V & I1=2 A in the shown circuit, using the…
A:
Q: 1. Analyze the working and compare the signal conditioning circuit used in fluid level and relative…
A: An electrical circuit known as signal conditioning modifies a signal in order to get it ready for…
Q: For Wheatstone bridge circuit, the following values are given. Vsupply=120V; R₁ = 15; R₂ =3002; R3 =…
A:
Q: 50 Ω. 3. Determine Zin of a lossless 50 2 transmission line N/4 long having a ZL =
A:
Q: For the parallel and series capacitors values of C₁= 70 µF, and C₂=C3=35 µF, C4-70 μF, C5-C6-35 μF,…
A: Given data Series and parallel combination of the capacitive circuit is given in the problem. C1=70…
Q: A single-machine infinite-bus power system is shown in Figure Q1, where the equivalent reactance of…
A: Given: In this question, the given details are, A single-machine infinite-bus power system is,…
Q: V=50 mV o + R₂ 10 ΚΩ R₂ 10 ΚΩ R₁ 100 ΚΩ Oinput impedance increases CMRR decreases Obandwidth…
A: Ideal op Amp High open loop gain High input impedence Low output impedence High CMRR....etc
Q: Hi, I got a 3 as my answer. Could you please check your work
A: The answer mentioned in the solution is correct i.e 4 ohms is the answer not the 3 ohms Answer you…
Q: ques Hon To Hind Here Vin = = 8Sin Lt) R sum un + Vout Yo at 4 seconds Let Diode is Ideau
A:
Q: Solve for the value of the capacitance (in nF unit) if R2-1017 ohms and Xc = 2316 ohms. Round your…
A: The question is about finding capacitance value.
Q: A 60 Hz sinusoidal voltage with an RMS value of 120 V is applied to a single-phase full-wave SCR…
A:
Q: The following questions use the per phase circuit model of the 3 phase syn- chronous machine that is…
A: Given: In this question, the given details are, A 3 phase synchronous generator has a synchronous…
Q: A 60 Hz sinusoidal voltage with an RMS value of 240 V is applied to a single-phase half-wave SCR…
A:
Q: If a 25μH inductor is connected to a voltage shown in the figure below: The current through the…
A: The mathematical expression of the given waveform can be obtained by using the line equation and…
Q: 8. The following plant is given: X(S) x(s) == Wo(s) y(s) y(s) =. ²/ S output signal W.(s) With input…
A: We need to find out the transfer function and we need to draw input and output .
Q: Required information Problem 05.001 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS The equivalent…
A: The given problem is from operational amplifier. The detailed solution is given in the next step
Q: Problem 05.028 - Non-inverting amplifier Calculate the output current of the given circuit, where v₁…
A: The given problem is from operational amplifier. The detailed solution is given in the next step
Q: For transformer which has, N₁-1000, N₂-250, V₁-120V and RLoad of 129. • What is the value of the…
A:
Q: circuit consisting of three resistors rated: 10 ohms, 15 ohms and 20 ohms are connected in delta.…
A: We need to convert the given delta to star .
Q: Required information Problem 06.015 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS Two capacitors…
A: The given problem is from capacitor. The detailed solution is given in the next step
Q: A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 74…
A:
Q: Find the Rth (in Ohm) of the circuit shown in Fig., to the left of the terminals a-b. RL = 6 Ω32 V…
A: We need to find out the thevenin equivalent resistance for given circuit.
Q: 1-F capacitor is connected in series with a 6-ohm resistor. If the connection is energized from an…
A: We need to find out the voltage across capacitor for given circuit.
Q: 12 V V 4 ΚΩ www 3 ΚΩ 2 ΚΩ www 1ΚΩ 8 V 5 ΚΩ 10 ΚΩ Find current across 10k ohm resistor. (1+ 6V
A: We need to find out the current for given circuit through given resistor .
Q: A step test of a transducer shows a signal having a damped oscillation decaying to a steady value.…
A:
Q: The ac voltage gain magnitude can be calculated using Eq. (10.31): Rc (47 ΚΩ) Av 2re 2(269)…
A:
Q: A d.c. 3-wire system is to be converted into a 3-phase, 4-wire system by adding a fourth wire equal…
A:
Q: The critical frequency at a particular time is 12.5 MHz. What is the optimum working frequency for a…
A: Given: Critical frequency, fc=12.5 MHz Angle of incidence,i=650
Q: 2. Explain working principle of 3-bit digital to analog converter.
A: Digital system is used for computer, control, communication, Instrumentation. Analog signal is…
Step by step
Solved in 2 steps with 1 images
- Solve the problem and simplify the output function using Quine–Mc Cluskey Methods. The following requirements must be met in solving the problem. Requirement:a. Truth Tableb. Timing Diagramc. Quine – Mc Cluskey Method d. Logic Diagram A private company wants to decide on a certain issue. Each of the four officials has an equal share of voting right. At least two of them must approve the solution in order to implement it. Each of them has a switch which closes to vote YES and open to vote NO.If a fault occurs in connections C5 (stuck-at-1) for the following logic circuit, the appropriate fault-test by using Boolean difference technique .......... C1 X1 Cs C2 X2 Cs C6 C10 C9 C7 t0 t2 t3 t1 OWe want to perform subtraction operation in which we need a full subtractor. First draw Truth table for full subtractor. Due to pandemic you are unable to get the desire component. but you have only eight- to-one multiplexers with you. What do you think, can you still perform subtraction operation with multiplexer or not? If yes, draw the logic circuit.
- Logic Gates:* 7404LS (NOT)* 7408LS (AND)* 7432LS (OR)* 7400LS (NAND)* 7402LS (NOR)* 7486LS (EX-OR)Or you can use 74HCxx versions. Task 2: 4 INPUT PRIORITY ENCODERa) Write the truth table.b) Find the outputs in terms of min terms using minimal expression.c) By using K map, find the simple/simplest expression of theoutputs.d) Draw the circuit diagram. (Simulation design will be accepted.)e) Simulate the circuit & explain your results. (Please do notdesign separate simulations for each output. You should design ONEsimulation including all inputs and outputs.)Design an 8-to-1 multiplexer using 4-to-1 and 2-to-1 multiplexers only. you will need to provide truth table, logic expression and circuit diagram.1. Construct the truth table for F. 2. From truth table in (1), design logic circuit for function F using various combinationof logic gates and an 8-to-1 MULTIPLEXER shown in Figure 8-to-1 MULTIPLEXER. Use A, B, C as aselector. 3.Use the same truth table in (1) to design logic circuit for function F using variouscombination of logic gates and a 4-to-1 MULTIPLEXER shown in Figure 4-to-1 MULTIPLEXER. UseA, B as a selector.
- The following waveforms are the input to the shift register you constructed in question #5. Based onthe waveforms for the CLK (clock) and D0 input (input on the leftmost Flipflop), generate thewaveforms for Q0, Q1, Q2, Q3, Q4. (Question #5 is "Using JK-Flipflops and Digital Logic Gates, build a 5-stage Shift Register")*A traffic light system uses logic gates as part of the control system. The system is operated when the output D has the value . This happens when either (a) signal A is red or (b) signal B is green and signals B and C are both red( NOTE: Assume for this problem that red=0 and green =1) Deduce the truth table for the system and the Boolean expression from the truth table, Hence Design a logic circuit or network9. Design a combinational logic circuit: to convert Excess 3 (3-12) to BCD code (0-9). Note: Assume don't cares (X) wherever necessary in the simplification process
- A logic function is expressed by the equation = 0.1.8.9.4. Plot the the values on the K-map below Note: w is the msb (most significant bit) 3 x 10 0- - W X 1 00 01 Write the simplified Sum of Products (SOP) expression. Use yz WIM or "" for NOT; 11 10 for AND; "+" for OR (without the quotation marks.1 - Design 3-bit Gray code generator 1-1 Construct the Truth Table of the 3-bit Gray code generator Logic Circuit. 1-2 1-3 1-4 Write down Standard SOP expression of the three output bits B2, B1, BO Without using minimization. Simplify the logic by using K-map. Write down the simplified expressions of B2, B1, B0. Sketch the logic circuit with basic gates.4. Use the Word table tool to construct the truth table for this circuit. Be sure to include intermediate values. Insert column headings in the first row. Be sure to use the Insert > Equation tool so that standard Boolean logic symbols are displayed in the headings. A B. D In the circuit implementation of an 8-bit adder, explain why the carry bit connection of the least- significant bit is connected to ground. Explain in words what values for A, B, C, D, E will cause a 1 to appear at point X. A B E