Latching current for an SCR, inserted in between a dc voltage source of 200V and the load, is 100 mA. Compute the minimum width of gate-pulse current required to run on this SCR in case the load consists of R= 20N in series with L = 0.2 H. (a) 100.503 µ sec (b) 111.624 µ sec (c) 120.512 µ sec (d) 90.10 µ sec

Latching current for an SCR, inserted in between a dc voltage source of 200V and the load, is 100 mA. Compute the minimum width of gate-pulse current required to run on this SCR in case the load consists of R= 20N in series with L = 0.2 H. (a) 100.503 µ sec (b) 111.624 µ sec (c) 120.512 µ sec (d) 90.10 µ sec

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The SCR operation characteristic is plotted for a. Va vs Ig with Ia as a parameter b. Ia vs Va with Ig as a parameter c. Ig vs Vg with Ia as a parameter d. Ia (anode current) vs Ig (gate current), Va (anode – cathode voltage) as a parameter
Question 30 The SCR operation characteristic is plotted for Not yet answered O a. la (anode current) vs Ig (gate current), Va (anode – cathode voltage) as a parameter Marked out of 1.00 Ob. P Flag question la vs Va with Ig as a parameter Oc. Ig vs Vg with la as a parameter d. Va vs Ig with la as a parameter
%3D For the circuit shown in Figure B23, a = 0.97, calculate the following: i. Collector current (Ic) ii. Collector-Base voltage (VCB) iii. Emitter Current (IE) iv. Base Current (IB) IE Ic 2.5 k2 Ouput 2.8V IB 10V VEE Vcc Figure B23
The arrow on the symbol of MOSFET indicates O a. that it is a N-channel MOSFET O b. the direction of conventional current flow O c. that it is a P-channel MOSFET O d. the direction of electrons
The gate current of an SCR full-wave rectifier is adjusted to 1.2mA and the forward breakdown voltage of SCR corresponding to this gate current is 150V. The applied voltage is a sinusoidal voltage of 300V peak, the load resistance is 100 ohms and the holding current is zero. Determine the a) firing angle b) conduction angle c) average output voltage d) average current and e) average power (Our lesson is POWER ELECTRONIC DEVICES, in the lesson of INDUSTRIAL ELECTRONIC)
CHOICE QUESTIONS 1. An SCR is a semiconductor device which consists of (a) four PN junctions (b) three PN junctions (c) two PN junctions (d) one PN junction. 2. After triggering an SCR, the gate pulse is removed. The current in the SCR will (a) immediately fall to zero (c) remain the same (b) rise up (d) immediately rise a little and then falls to zero 3. An SCR may be turned OFF by (a) reversing polarity of the anode-to-cathode voltage (b) interrupting its anode current (c) low-current drop out (d) all of the above.
4. An RC filter stage (R = 33 0, C = 120 HF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage. *****END*****
* The specified value of holding current for an SCR means that The device will turn on when the anode current exceeds this value The device will turn off when the anode current falls below this value The device may be damaged if the anode current exceeds this value The gate current must equal or exceed this value to turn the device on * Once in saturation, a further increase in base current will cause the collector current to increase not affect the collector current cause the collector current to decrease turn the transistor off
The arrow on the symbol of MOSFET indicates O a. that it is a N-channel MOSFET O b. that it is a P-channel MOSFET Oc. the direction of electrons O d. the direction of conventional current flow
A silicon controlled rectifier (SCR) has a forward breakdown voltage of 230 V. When a gate current of 2 mA flows in the gate circuit. If a sinusoidal voltage of 400 V peak is applied, find the following: Firing angle. Average output voltage. Average current for a load resistance of 180 Ohms. Power output
Q4-What is the fire angle that required to design an R-triggering circuit for a half wave controlled rectifier for SCR, the following parameters are applicable Igt(min) S0HZ „Resistance in gate current path = 60 k. 0.5mA, Vgt(min) = 0.7V, Vd=0.7V, Supply voltage = 30 V, LOAD
The gate current of a SCR half-wave rectifier is adjusted to 1.25mA and the forward breakdown voltage of SCR corresponding to this gate current is 110V. The applied voltage is 220V, the load resistance is 150 ohms and the holding current is zero. Determine the a) firing angle b) conduction angle c) average output voltage d) average current and e) average power (Our lesson is POWER ELECTRONIC DEVICES in the subject INDUSTRIAL ELECTRONIC)