In an M/M/1 queuing system, the number of arrivals in an interval of length T is a Poisson random variable i.e. the probability of there being e-^T (2T) n arrivals in an interval of length Tis n! The probability density function f(t) of the inter- arrival time is given by

In an M/M/1 queuing system, the number of arrivals in an interval of length T is a Poisson random variable i.e. the probability of there being e-^T (2T) n arrivals in an interval of length Tis n! The probability density function f(t) of the inter- arrival time is given by

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1: The number of bacterial cells (P) in a given reactor is related to time in days (t) as described by the following mathematical model: dp dt 0.0000007 P², If at initial time (P = 106). Determine the number of cells when (t 2days) using the fourth order Runge-Kutta method and at time increment of (1 day). = = 0.3 P 1
An object is shot upward from the ground with an initial velocity of 640 ft/sec, and experiencés a constant deceleration of 32 ft/sec² due to gravity as well as a deceleration of (v(t) / 10) ft/sec due to air resistance, where v(t) is the object's velocity in ft/sec. (a) Set up and solve an initial-value problem to determine the object's velocity v(t) at time t. (b) At what time does the object reach its highest point?
The stress profile shown below is applied to six different biological materials: Log Time (s] The mechanical behavior of each of the materials can be modeled as a Voigt body. In response to o,= 20 Pa applied to each of the six materials, the following responses are obtained: 2 of Maferial 6 Material 5 0.12 0.10 Material 4 0.08 Material 3 0.06 0.04 Material 2 0.02 Material 1 (a) Which of the materials has the highest Young's Modulus (E)? Why? Log Time (s) (b) Using strain value of 0.06, estimate the coefficient of viscosity (n) for Material 6. Stress (kPa) Strain
Simulink Assignment- Filling a Tank In fluid mechanics, the equation that models the fluid level in a tank is: dh 1 -(min Ap - mout) dt h is the water level of the tank A is the surface area of the bottom of the tank pis the density of the fluid Mim and mout are the mass flow rates of water in and out of the tank, the flow out is a function of the water level h: 1 mout Vpgh Ris the resistance at the exit. Assume that the exit is at the bottom of the tank. g is the gravitational acceleration What to Do: 1. Build a model in Simulink to calculate the water level, h, as a function of time. Your model should stop running as soon as the tank is full. 2. Assuming the height of the tank is 2 meters, after how many seconds does the tank fill up? Use the following constants to test your model: • A: area of the bottom of the tank = 1 m? • p: the density of fluid = 1000 kg/ m? • R: the resistance at the exit = 3 (kg.m)-1/2 • ho: Initial height of the fluid in the tank = 0 m • g: the gravitational…
Energy of a Roller Coaster Car 500 450 400 350 --- 3 300 250 E 200 150 100 50 6 8 10 Time (s) Mechanical Energy ....... Potential Energy -- Kinetic Energy This graph shows different types of energy for a roller coaster car that starts at the top of a large hill and goes down to its lowest point at 6 s. According to the graph, what is the most likely relationship between height and potential energy? Your answer: They are directly related. They are inversely related. There is no relationship between the two. There is not enough information for a conclusion.
Manufacturing process with two variables x1,x2 described by the empirical model: y=bo +b1 x1 + b2 x2 + b12 x1 x2 + b3 (x1)^2 +b4 (x2)^2 please refere to the image attached
H.W: suppose that a team of three parachutists are connected by a weightless cord while free falling at a velocity of 5 m/s. Using Gauss Elimination Method calculate the tension in each section of cord and the acceleration of the team, given the following information: 3 Parachutist Mass Kg(m) Drag Coefficient Kg/s (c) a 1 70 10 2 60 14 3 40 17 1 Hint: The equation of motion can be determine from Newton's Second Law (Σ F = ma). m₁g-Tc₁v = m₁a m₂g + T-R-C₂v = m₂a m3g+ R-C3v = mza R T 2
1.4 Define nett P-F interval
2. The CPU time requirement X of a typical job can be modeled by the following hyperexponential distribution: P(X ≤t)= a(1-e-¹²)+(1-a)(1-e-²¹), where a = 0.6, A₁ = 10, and A₂ = 1. Compute (a) the probability density function of X, (b) the mean service time E[X], (c) the variance of service time Var[X], and (d) the coefficient of variation. Plot the distribution and the density function of X.
For the model defined in Question 1, is the closed loop system with the negative feedback control law? 0 0 0 ;]* X 0 u=-Kx= O a. O b. O c. unstable 0 1 0 asymptotically stable not unstable O d. not asymptotically stable
6. A ball is thrown straight up in the air at time t = 0. Its height y(t) is given by y(t) = vot - 791² (1) Calculate: (a) The time at which the ball hits the ground. First, make an estimate using a scaling analysis (the inputs are g and vo and the output is the time of landing. Think about their units and how you might construct the output using the inputs, just by matching units). Solve the problem exactly. Verify that the scaling analysis gives you (almost) the correct answer. (b) The times at which the ball reaches the height v/(4g). Use the quadratic formula. (c) The times at which the ball reaches the height v/(2g). You should find that both solutions are identical. What does this indicate physically? (d) The times at which the ball reaches the height v/g. What is the physical interpretation of your solutions? (e) Does your scaling analysis provide any insight into the answers for questions (a-e)? Discuss. (Hint: Observe how your answers depend on g and vo).
The governing equation of motion for a base motion system is given by (assume the units are Newton) mä(t)+ci(t)+kx(t) =cY@, cos(@,t) +kY sin(@t) %3D Given that m = 180 kg, c = 30 kg/s, Y = 0.02 m, and о, — 3.5 rad/s %3| 1. Use Excel or Matlab to find the largest value of the stiffness, k that makes the transmissibility ratio less than 0.85 2. Using the value of the stiffness obtained in part (1), determine the transmitted force to the base motion system using Matlab or Excel. 3. Display and discuss your results.