In a slider crank mechanism the crank is making an angle of 45° with IDC. The crank and connecting rod lengths are 100 mm and 300 mm respectively. The driving moment on the crank is 50 Nm. Determine the force on the slider that is necessary to be applied for the equilibrium of the linkage.

In a slider crank mechanism the crank is making an angle of 45° with IDC. The crank and connecting rod lengths are 100 mm and 300 mm respectively. The driving moment on the crank is 50 Nm. Determine the force on the slider that is necessary to be applied for the equilibrium of the linkage.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Equilibrium of Concurrent Force System. The piston of a reciprocating engine exerts a force of 175 kN on the crosshead when the crank is 45° (angle B) past TDC. If the stroke of the piston is 800 mm and the length of the connecting rod is 1.80 m, find the guide force and the force in the connecting rod. Hint: 1=½ stroke; Angle o may be solved using Sine Law in AACO. K= Compressive Force in the connecting Rod E= Piston Effort 70 120 F, = Guide Force Fig. P-1 Fig. P-2 a Tools: EF cos0=0; F sin .=0. R = Ev)* + (E#): ; R 771 =- : tane = sin A sin B sin C
It is desired to balance the rotor shown in the figure by placing balancing masses at a distance of ei and Li mm from the rotation axis in the R and L balancing planes. Find the balancing masses and their angular positions to be used in balancing. in the tableUse the given values.Find the L and R support reactions.
At midpoint, the cord is pulled rightwarduntil it makes an angle of 40° with thehorizontal support. What is the requiredmagnitude of the force to keep the systemstationary?
What is static force analysis? A four bar mechanism has following dimensions: Length of crank=100 mm, Length of coupler link=450mm, length of rocker-270 mm and length of fixed link=250 mm. A force.F=-100i N is applied on to mid-point 'C' of rocker, when crank makes 120° from positive x-axis. Calculate pin forces and torque to be applied on to the crank for equilibrium. 1. A disturbing mass 'm' kg is attached to a shaft. The shaft is rotating at 'n' rpm, The radial distance of the center of gravity of the disturbing mass from the axis of rotation is 'r' mm. It is required that the disturbing mass should not be disturbed by any addition or subtraction of mass. Suggest the ways to balance the system and justify by proper expressions. 2.
A plate inside a microwave is rotating by a motor that is connected to it's center. the plate is sitting on 3 wheels , as you can see in the picture . a. Draw a forces diagram on a small wheel b. Calculate the minimum motor's torq that is needed in order to spin the plate. given: Mass of the plate: Mp Mass of one wheel :Mw Static friction coeffient: miu(s) Radius wheel : r Radius plate : R Anything else that needed just add , thank you
(Repost) Can you assist with a detailed solution for the dynamic force analysis of the linkage mechanism aswell.
I need correct answer At stationary the tension in pulley 120N. Find tension in each side and Power trans when belt is on the point of slipping on smaller wheel. The wheel is 250mm diameter and fac F Friction 0.32. The angle of Lap 165⁰. The wheel speed 1200 C/min.
Q2/ A compound steam engine develops 250 kW at 80 r.p.m. The coefficient of fluctuation of energy as found from the turning moment diagram is to be 0.15 and the fluctuation of speed is energy as feed 1% of the mean speed. Find the weight of the flywheel required, if the radius of gyration is 1.5 m. T
Q3 a. Define the following term 1. Lateral vehicle dynamics 2. oversteers 3. steering wheel shimmy 4.d'Alembert Force Q3 b When deriving the force acting on the wheel to determine the maximum grade we can E without wheel slippage (traction limited gradeability) then Write the equation that relate total mass of the vehicle in case of a Front wheel duiveWD ), on Rear wheel Drive (RWD in case of All wheel drive (4WD) power train ? s
The figure shows a mechanism that raises packages in a transfer mechanism. A 200-N package sits on the horizontal output link O4BD while the crank O2A is rotating at constant speed of 287 rpm CCW. At the position shown the crank OA is vertical and the output link OB is horizontal. we need to determine the torque required from the motor at the crank O2A and the force in member AB The weights of the links are negligible. 50mm 450mm 200 N 200 mm B. 374 mm 300mm X The angular velocity of the link OĄBD in rad/s is = Choose... + The magnitude of the velocity of point D in m/s is = Choose... + The torque required from the motor at the crank O2A in N.m is = Choose... : The force in member AB in N is = Choose... +
Find the true magnitude and direction of forces on the wheel and cable members at static equilibrium.
The figure shows a mechanism that raises packages in a transfer mechanism. A 500-N package sits on the horizontal output link O4BD while the crank O2A is rotating at constant speed of 400 rpm CW. At the position shown the crank OA is vertical and the output link O4B is horizontal. we need to determine the torque required from the motor at the crank 02A and the force in member AB The weights of the links are negligible. 30mm 450mm 500N 220 mm B 374 mm 374 mm The angular velocity of the link O,BD in rad/s is = The magnitude of the velocity of point D in m/s is =