If the voltage across a 12 F capacitor is 14 t e-3t V, calculate the power at t = 23 ms.
Q: Find the capacitor size that wiIl make the light stay on for 10 sec after power is removed switch is…
A: The solution is given below
Q: Q/ Use The following circuit to design an oscillator of 5KHZ out The amplifier used in this…
A:
Q: How can the error amplifier control the output voltage of a buck converter? Please explain.
A: Types of DC-DC Converters Buck Converter Boost converter Buck-Boost Converter Flyback Converter…
Q: 1. An alternating voltage is given by i = 30 sin (200nt + a/3) volts. Find (a) the amplitude, (b)…
A: The solution is given below
Q: A single-phase transformer, rated at 25 kVA, 2200 / 60
A:
Q: 1. Explain briefly in one(1) sentence how do we maximize the value of the armature current in a…
A: (1) When the load gets added to shunt wound DC motor the speed gets reduced and along with the speed…
Q: Given the circuit shown below with a drain current of 0.2 mA and a drain voltage of +0.4 V. The…
A: The solution is given below
Q: 15-9. Determine the directivity gain (in dB) for an antenna that produces a power density at a point…
A: Given, Power density at a point is 40 times greater than power density at the same point when…
Q: Find the acceleration (m/s?) of the mass M for the system shown. M-1 kg, F-96 N (Assume g= 10 m/s)…
A: We need to find select correct option for acceleration
Q: Directions: From the illustration, identify the branch current for each resistor. Consider: RI = 100…
A:
Q: An electron ( me = 9.11x1031 kg- q=1.6x1091 C) moves in a circular path perpendicular to a uniform…
A: Given, Mass of electron, me=9.11×10-31 kg Charge on electron, q=1.6×10-19 C Magnetic field, B = 7.3…
Q: b) Solve the given two numbers using BCD addition. (C5) ,„ + (B2) „ =(?),D 16 16
A: Given, C516+B216=?BCD
Q: 4. What is the relationship between gain, feedback and Deviation?
A:
Q: 1- How does a diode wo a voltage regulator? 2- What is a Zener breakdown? 3- What happens to the…
A: In this question we will write about how diode work as a voltage regulator.....
Q: Given F(s) = (49384)/(( S-89)2 + 24674)), the f(t) would be:
A:
Q: For a specific application, the circuit shown in Fig. 2.140 was designed so that I, = 90 mA and that…
A: Steps: A design question may have multiple solutions. Here the different possibilities of R1 and R2…
Q: Given an input signal power of 1mW, an output signal power of 6mW, an input clutter power of 1mW,…
A: Given data, Input signal power, Si=1 mW Output signal power, S0=6 mW Input clutter power, Ci=1 mW…
Q: Q1- A universal motor with 120V,50 Hz,2 poles. runs at speed 7000 rpm and draws full load current…
A: The solution is given below
Q: Explain the origin of negative voltage regulation in a transformer. Derive the equation of no-load…
A: We will answer both subparts. It is asked to explain the origin of negative voltage regulation in a…
Q: Calculate the current required to produce a deflection of 100°, if the coil of a PMMC instrument has…
A: Given, Deflection angle, θ=100° Number of turns N=60 turns Area, A = W×L=18×10-3×25×10-3=450×10-6 m2…
Q: What are the different media for wave propagation? Discuss the wave propagation in each media with…
A: Three types of the electromagnetic wave propagation mode, Ground wave propagation Space wave…
Q: A single-phase transformer has maximum efficiency of 98 %. The core losses are 80 W and the…
A: Given: A single phase transformer has Maximum efficiency, ηmax=98 % Core loss, Pi=80 W Equivalent…
Q: Solve the given symbolic initial value problem. у'+ 9y'+ 20y 3D е ""6(t-3); у(0) 3 2, у'(0)%3 - 9…
A: The solution is given below
Q: Determine current, Pr, ST, Qr 4 the circuit of 3+3 jatj
A: First calculate equivalent impedance seen by current source and then find active, reactive and…
Q: Problem 3: AV= 98-V source is connected in series with an R = 1.4-kQ resistor and an L = 26-H…
A: Energy dissipated in this time is the difference of the energy stored at initial time and time at…
Q: 6. Find a closed form for the generating function for the se- quence {a,}, where b) a, = 2" for n =…
A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…
Q: Which of the following equipment should be installed by the consumers having low power factor…
A:
Q: Given the flux density D = (6/r) cos(2θ) aθ C/m2, use two different methods to find the total charge…
A: The solution is given below Basic problem on charge
Q: Find the charge density on a conductor surface in free space i (a) Ē = 400(āx – āy + 3ā,) V/m at the…
A: Given data: E=400ax-ay+3az V/m The charge density ρ is obtained Now,…
Q: Consider the circuit in Fig. 6.83. Find: (a) Leq, i(t), and i2(t) if i, = in the 20-mH inductor at t…
A:
Q: | What is the advantage of atomic force microscope (AFM) compared to scanning tunneling microscope…
A: a. The advantages of the atomic force microscope(AFM) as compared to the scanning tunneling…
Q: Qs: Identify whether the follawing systems are static, dynamic, time invariont, Linear or causal. A.…
A:
Q: Determine the total inductance, Lt at terminals A-B in the network in Figure Q1(a). 1 mH 2 mH 4 mHC…
A: Given:
Q: Exttet us find गकर्ण density at iP(z5 plane Z=oif th 3oncm Located
A: In this question we will find the surface charge density at given point on given conducting plane...
Q: Describe the importance of using Bandpass filter in ASK Modulator.
A: In this question we will write importance of bandpass filter in modulator ...
Q: Solve for i(t) for t > 0. The initial conditions are i (0) = 0 and V. (0) = 0.1V. t=0 1000 mH i(t)…
A:
Q: solve for the prinapal 0th root of 20/00 7 5o (cos 20+ jsin 20)
A: The solution is given below
Q: r R1=9, R2=3, R3=6, R4=6, K1=2 and 1=11 A in the shown circuit, find the node voltages: R1 Kl i, R4…
A: In this question we will find node voltages using kCL...
Q: Determine the flux per pole for 6 pole dc machine having 240 wave connected conductors, which…
A: Given Z=240 wave connected A=2 wave connected, E=V=500v , speed N=1000rpm, P=6, flux(phi)=?
Q: In a parallel combination of two milli ammeters with full scale deflections 5 mA and 20 mA shows…
A: Given data: A parallel combination of two milli ammeters with full scale deflection current, IFSD1=5…
Q: Hot carrier diodes are also known as a. tunnel diodes. • b. PIN diodes. O c. Schottky diodes • d.…
A: In this question we will write about hot carrier diodes etc.....
Q: The current through a 5 mH inductor is shown in Fig. 6.66. Determine the voltage across the inductor…
A:
Q: A B Y 1. D ABCD 00|0 X YZ 1 1 1 1 1 1 1 1 1 1 1 Write the expressions for the outputvariables 1 1 X…
A: A logic gate circuit along with its truth table is given in the question. We need to give the…
Q: A 275mH inductor with a quality measure of 6 and a 1502 resistor are series connected to a 120V,…
A: Given a series RL circuit, Inductance, L = 275 mH Quality measure, Q = 6 Resistance, R = 150 ohm…
Q: I tja A 200 L/20°V 200L0° V 8tja Itjor 200 L-120° ♡ 5-j3 | +js
A:
Q: 5-20. Determine the net receiver gain for an AM receiver with an RF input signal power of -87 dBm…
A: The solution is given below
Q: The cylindrical surface ρ = 8 cm contains the surface charge density, ρS = 5e−15|z| nC/m2. What is…
A: In this question cylindrical surface with surface charge density is given...We have to find out to
Q: Q2- What is the Working Principle of DC Servo Motor
A: servo motor is a rotary actuator or a motor that allows for a precise control in terms of the…
Q: A 220V short-shunt compound generator has armature resistance, series field resistance and shunt…
A:
Q: Q3: The output for the following clipping circuit is shown below. Assuming ideal diode, calculate go…
A: Brief description : In the above given question they have mentioned a clipper circuit. Clipper…
If the voltage across a 12 F capacitor is 14 t e-3t V, calculate the power at t = 23 ms.
answer in Watts.
Step by step
Solved in 2 steps with 2 images
- A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
- Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?Capacitive Circuits Fill in all the missing values. Refer to the formulas that follow. XC=12fCC=12fXCf=12CXc Capacitance XC Frequency 38 F 60 Hz 78.8 400 Hz 250 pF 4.5 k 234 F 10 kHZ 240 50 Hz 10 F 36.8 560 nF 2 MHz 15 k 60 Hz 75 nF 560 470 pF 200 kHz 6.8 k 400 Hz 34 F 450
- You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a current draw of 36 amperes at full load. The motor is connected to a 480-volt line. A three-phase wattmeter indicates a true power of 22 kW. Determine the power factor of the motor and the amount of capacitance needed to correct the power factor to 95. Also determine the minimum voltage rating of the capacitors. The capacitors are to be connected in wye.You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
- What is the minimum AC voltage rating of each capacitor in Question 11?In a pure capacitive circuit, does the current lead or lag the voltage?A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?