Can i get the answer for the 3 questions • Pre-WWII: The Titanic• WI: Liberty shipsReprinted w/ permission from R.W. Hertzberg,"Deformation and Fracture Mechanics of EngineeringMaterials", (4th ed.) Fig. 7.1(a), p. 262, John Wiley andSons, Inc., 1996. (Orig. source: Dr. Robert D. Ballard,The Discovery of the Titanic.)Reprinted w/ permission from R.W. Hertzberg,"Deformation and Fracture Mechanics of EngineeringMaterials", (4th ed.) Fig. 7.1(b), p. 262, John Wiley andSons, Inc., 1996. (Orig, source: Earl R. Parker,"Behavior of Engineering Structures", Nat. Acad. Sci.,Nat. Res. Council, John Wiley and Sons, Inc., NY,1957.)Problem: Steels were used having DBTT's just belowroom temperature.Your task :• On the 14th of April in the year 1912, the R.M.S. Titanic was on its way from Southampton, England toNew York, United States when it collided with a massive iceberg. Of the 2200 passengers and crew thatwere aboard, only 705 survived. When the Titanic struck the iceberg, the hull'plates did not deform, asthey should have. Instead, they fractured! The investigation shows that:• The water temperature was below freezing• The Titanic was traveling at a high speed on impact with the iceberg• The hull steel contained high levels of sulfur.From the statement above,(i)Explain why the titanic was failed catastrophically(ii)Determine the suitable laboratory testing for the failure part.(iii)Explain how to characterize the failure part.(iv)Recommend the suitable materials for the ship that will travel at different extreme temperatures.Justify your answer.

1. It should be a type of catastrophic failure in the structural materials because of the below…

Answered: (i)Explain why the titanic was failed…

(i)Explain why the titanic was failed catastrophically (ii)Determine the suitable laboratory testing for the failure part. (iii)Explain how to characterize the failure part.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What are the importance of fracture toughness (KIC) and fatigue crack growthrate (da/dN) in design?
You are given a 10-cm-diameter cylindrically shaped extruded bar (length = 50 cm) of an aluminum alloy. a. What specimen configurations would you use to characterize the degree of anisotropy of the material’s fracture toughness? b. If the lowest fracture toughness of the bar was found to be 20 MPa √m , what would be the load level needed to achieve this stress intensity level? c. Confirm the presence of plane-strain conditions, given that σys = 500 MPa. (Assume specimen thickness = 1 cm, a/W = 0.5, and bar diameter = 1.2 W.)
QI/ If the thermal shock resistance of RBSN is 2214 w/m, poission ratio= 0.2 , cofficient of expansion= 2.6 x 10 /k, thermal conductivity=9 w/ m.k, specific heat= 0.86 j/ g.k ,thermal diffusivity= 4.4 x10 m /s, modulus of elasticity = 200 Gpa Calculate : 1.fracture streangth in Mpa 2. the density in Mpa 3. the thermal shock resistance in m' k/ s
An airplane part is to be designed from view point of Fracture Toughness for which two materials are available. Consider Y=1.2 and ow =400 MPa, calculate (a) maximum internal crack length under the given condition for each material type. (b) How much stress on Aluminum part can be increased/decreased to comply with the critical crack length of 3 mm. 1/2 Кіс, МPa m Aluminum (7075-T3) 30 Titanium Ti-6AI-4Va 55
1. For the stress-strain curve shown below, please estimate the properties indicated. (a) Fracture Strain Please do your work on a separate sheet of paper, and put your answers in the boxes on the right. Be sure to include the proper symbol and units. Stress Strain 70 60 50 Stress (ksi) 240 30 20 10 70 0 0.000 60 50 Stress (ksi) 40 20 10 KULL 0 0.000 0.010 0.050 0.100 Strain (in/in) Stress Strain 0.020 0.030 Strain (in/in) 0.040 0.150 0.050 (b) Ultimate Tensile Stress (c) Fracture Stress (d) Proportional Limit (e) Elastic Modulus (1) Yield Stress (g) Tensile Toughness (Modulus of Toughness) (h) Modulus of Resilience
You have been asked to draw up a specification for a ceramic cladding tile that is likely to experience tensile stresses of 64 MPa during its installation and service lifetime. If the ceramic has a specific surface energy of 0.28 J/m2 and its Youngs Modulus is 82 GPa what would be the maximum length of an internal flaw that would not result in fracture of the tile? (This question has only one correct answer) O a. 3.79 mm O b. 7.14 mm c. 7.57 um Ο d.3.79 μm O e. 3.57 µm O f. 3.57 mm g. 7.14 um
6. A ceramic part for a jet engine has a yield strength of 648 MPa and a plane strain fracture toughness of 8.49 MPam 4. To be sure that the part does not fail, we plan to ensure that the maximum applied stress is only one-third of the yield strength. We use a nondestructive test that will detect any internal flaws greater than 0.27 mm long. Assuming that the Y constant is 1.4, does our nondestructive test have the required sensitivity? Explain.
What is thermal gradient in thermal stress [explained thoroughly]
What is thermal stress analysis? [own words]APPLICATION OF THERMAL STRESS
A very wide plate with a 2" long center crack is heated in order to be brazed to its end supports. The plate is made of a material with Elastic modulus of 15x10$psi and a = 6x10-º in/in/°F. Considering the brazed ends become rigid supports at 400°F and assuming that the material has a constant Fracture Toughness of 30ksivlin, at what temperature will the plate fracture? [hint: use B (geometric factor) =1.0 for this geometry]
You have been asked to draw up a specification for a ceramic cladding tile that is likely to experience tensile stresses of 89 MPa during its installation and service lifetime. If the ceramic has a specific surface energy of 0.35 J/m2 and its Youngs Modulus is 85 GPa what would be the maximum length of an internal flaw that would not result in fracture of the tile? (This question has only one correct answer) a. 2.53 µm b. 5.06 µm c. 4.78 μm d. 2.53 mm e. 2.39 mm f. 4.78 mm g. 2.39 um
In designing a ceramic part for a jet engine, to ensure that the part does not fail, we plan to ensure that the maximum applied stress is only one-third of the yield strength. The yield strength of this CMC part for a jet engine is 520 MPa, and its plane strain fracture toughness is 5.5 MPa√?. We utilize a nondestructive test to find any internal faults that are longer than 1.27 mm. Does our non-destructive test have the requisite sensitivity if Y = 1.4? Explain.