Identify and explain the safety procedures and precautions when working with tools and equipment’s that should be followed during the installation of the cables?
Q: What NEC chapter contains tables that are used to determine the proper size of a conductor?
A: The NEC is the worldwide accepted code for electrical wiring and installation. To determine the…
Q: In the conduit layout shown in picture attached, determine how many wires are contained in each…
A: The circuit is shown below: Between the three-phase line and the disconnect switch. The switch is…
Q: what wire size is needed on a one 20 amp, 120-volt laundry branch circuit? what wire size is needed…
A: 12 gauge what wire size is needed on a one 20 amp, 120-volt laundry branch circuit.
Q: Why is bonding of the conduit necessary when using reducing bushings to properly match a conduit to…
A: In such situations, conduit bonding is done to prevent or mitigate shock hazard as it provides a low…
Q: Discuss application and uses of earth leakage breaker ?
A: ELCB (Earth Leakage Circuit Breaker):- An ELCB (Earth Leakage Circuit Breaker) is an electrical…
Q: 9. How is equipment containing ungrounded electrical systems required to be marked? A. With green…
A: An ungrounded system is a system that is not grounded intentionally. The neutral wire of an…
Q: when installing coaxial cable the minimum bending radius generally recommended is
A: Coaxial cable: It is an electrical cable. It consists of an inner conductor along with a concentric…
Q: Q.1: Non-metallic conduit must not be installed where extremes of ambient temperature, why?
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: What type of conduit that should be used where corrosion is a factor?
A:
Q: Identify and explain the safety procedures and precautions when working with tools and equipment's…
A: Electrical cables are used for transferring the signals and are also used for long distance…
Q: What device can determine how far a cable damage is?
A: we have to give detail about the device that can determine "how far a cable damage is".
Q: What is the minimum branch circuit wire size that may be installed in a dwelling?
A: Basically, the 14 AWG wiring is used for typical lightening loads in the residence.
Q: Which of the following would help avoid the choke effect in grounding electrode conductors? A.…
A: The correct option is B that us using an appropriate PVC(POLY VINY CHLORIDE) CONDUIT WILL AVOID…
Q: Table 314.16(A) of the Code shows the maximum number of conductors permitted in a given size box. In…
A: When setting a job, an electrician often makes a circuit, thinking of the best way to use wires…
Q: 1. Identify and describe the step-by-step process used to pull cable and also describe the…
A: The step-by-step process used to pull cable STEP 1: Check the Cable Width and Pipeline to make sure…
Q: what section of the code prohibits supporting telephone wires from raceways that contain light or…
A: N.E.C. ARTICLE 820 article covers coaxial cable distribution of radio frequency signals or covers…
Q: What is the name of the gadget that can determine the distance between a cable's damage and where it…
A: Name of the gadget which is used for finding the cable damage and its location is "Cable Fault…
Q: Identify and explain the safety procedures and precautions that should be followed for fire…
A: Procedure that is used to install cable in buildings are as follows:- Electrical conduction for…
Q: draw a schematic diagram of the jumpers connected to the front panel of a computer system unit.
A: Jumpers allow the computer to shut down the electrical circuit, allowing electricity to flow to…
Q: List the methods by which an equipment grounding conductor is connected to a device box
A:
Q: what is grading of cables, explain proper in details with block diagram
A: In a single-core cable, the conductor is surrounded by the dielectric material with an outer…
Q: 10.a. Which of the following is a condition of the exception that allows the grounded conductor of…
A: According to guidelines we need to solve only first question. According to the question we have to…
Q: Define line of support
A: The line support in terms of electrical energy is defined below: - The various kinds of structure…
Q: How can you calculate the maximum short-circuit current that can pass when the A-B ends of an outlet…
A: The detailed answer is solved below according to the given parameters and instructions in the…
Q: Why is the Insulating plastic of wires color-coded?
A: Wire A wire is a thin, malleable metal strand. The most common way to make wire is to draw the metal…
Q: What type of bonding jumper connects the grounded circuit conductor and the equipment grounding…
A: In a power system , Main bonding jumper connects the grounded circuit conductor and the equipment…
Q: when the insulation of the equipment tested healthy ? justify .
A: As we know that the current sent through a conductive wire to the destination means to the consumer…
Q: Explain the two main testing process used in testing transmission cables.
A: Fiber optics is a technology that is connected with the transmission of information as light rays…
Q: 6. Which of the following is a condition that a liquidtight flexible metal conduit must meet in…
A: Given :few mcqs on flexible metal conduit
Q: Question#03: Justify: why electrical isolation and theft prevention are the advantages of…
A: 1. The main benefits of non-conductive cable are its isolation from the rest of the system and its…
Q: single-pole portable cable connectors for a portable switchboard on stage, where used, shall be…
A: single-pole portable cable connectors for a portable switchboard on stage, where used, shall be…
Q: Four No. 12 and four No. 10 conductors are to be installed in a EMT conduit. What size EMT conduit…
A: Conductors size is selected on the basis of assigned numbers. As the assigned number increases then…
Q: use a conventional 12 volt test light to diagnose components and wires in a computer system . True…
A:
Q: What is the type,application and rating of cables?
A: Types of cable are classified according to their Voltage level .
Q: 4.Justify: why electrical isolation and theft prevention are the advantages of non-conductive cable?
A: According to the given question, it is required to determine the reason why non-conductive cables…
Q: Identify and describe the step-by-step process used to pull cable and also describe the step-by-step…
A: The step-by-step process used to install cable in buildings are as follows:
Q: Which type of cable would you use to connect two buildings in an office installation? A. Buried…
A: Given & to find: Which type of cable would you use to connect two buildings in an office…
Q: Identify and describe the step-by-step process used to pull cable and the step-by-step process used…
A: 1. The first step is to to lay electrical conduction of 2mm thick and 25 mm in size for the PVC…
Q: Justify: why electrical isolation and theft prevention are the advantages of non-conductive cable?
A: The main advantages of non conductive cable is it's isolation from the rest and most of the…
Q: Where insulated conductors are deflected within a wireway, either at the ends or where conduits,…
A:
Q: Airframe Electrical What is the purpose of the inspection hole on a connector contact?
A: There are different kind of connectors. Crimped contacts are mostly used connectors.Connectors are…
Q: What do you mean by permissible current loading of an underground cable?
A: Permissible current loading: It is the maximum amount of current the cable can carry without any…
Q: Airframe Electrical How much of the conductor should be exposed past the end of properly crimped…
A: Crimped contact is used to provide maximum reliability and safety to electrical equipment.There are…
Q: draw a pictorial/wiring diagram of the jumpers connected to the front panel of a computer system…
A: The Front Panel Connections, also known as the Front Panel Header or FPanel, are a collection of…
Q: Why is it critical to keep cable clutter to a minimum in a rack?
A: It is asked to explain why it is critical to keep cable clutter to a minimum in a rack.
Step by step
Solved in 4 steps
- In what ways may the Instrusion detection and prevention system be used to reduce the hazards of working from home?Lockout is required: During servicing and maintenance where unexpected ener- gization or start-up of equipment could harm employees. During repair and replacement work, and during renovation work. a. b. C. During modifications or other adjustments to powered equipment. d. All of the above. Lockout may involve: Opening a disconnect switch. b. a. Closing a valve. Placing a block in the equipment. d. All of the above. C. Lockout is the process ci Shutting off a machine at the end of a shift. Warning equipment operators about the risks involved in bypassing a machine guard. Preventing the flow of energy from a power source to a piece of equipment, and keeping it from operating. a. b. C. d. Preventing mechanics from starting repairs without the machine operators' knowledge. Tagout: Serves as a warning. b. Physically restrains a person from operating a power source. Must be applied using specialized tagout tools. a. C. d. Must be worn like a badge by the employee who is doing the repairs.…Using Manual drawing or CAD. Convert the pictorial cabling to a wiring diagram
- Explain safe work practice requirements for Non-Electrical Workers?A cable wire maybe coaxial or twisted. Coaxial costs 25 centavos per meter while twisted wire costs only 18 centavos. The soldering cost for coaxial wire is P1.30 per connection, for twisted wire P1.70. What length of cable run will make the cost of installing coaxial equal to that of the twisted wire. Assume that the number of soldered connection is 350. ANSWER_____________mExplain the relevance of earthing and bonding in an electrical Installation.
- Identify the system which has low stability. a. None of the above b. Open loop and Closed loop system c. Open loop System d. Closed loop systemIdentify and describe the step-by-step process used to pull cable and also describe the step-by-step process used to install cable in buildings?F.a-The best method of performing pneumatic system inspection is with a(n)A. ultrasonic listening device.B. vibration listening device.C. screwdriver to your ear.D. careful eye on system operation.F.b- What type of seal system is constructed of a hard brittle material and is often used in a pump to sealbetween the pump and the motor?A. SteelB. FiberglassC. CeramicD. GlassF.c- When a pneumatic solenoid fails, the failure is normally due to aA. weak pilot.B. bad spool.C. ripped seal.D. faulty coil.
- While discussing armature testing: Technician A says to test for shorts, place the ohmmeter leads on a commutator segment and armature shaft. Technician B says that continuity should exist between the commutator and the armature shaft. Who is correct?Why is it important, when soldering connectors onto a piece of electronic circuitry, to leave no pointy protrusions from the solder joints?Training is required for: Qualified electricians only. Only those workers who work on or near exposed energized parts. Both those workers who work on or near exposed energized parts and those who do not. None of the above. a. b. C. d. Workers who are designated as "unqualified:" Do not need any training. Must become "qualified" within one year. a. b. Must not operate electrically powered equipment. Must be trained in safety-related work practices. C. d. Workers who are designated as "qualified." Work on or near exposed energized parts. a. b. Must be trained to distinguish exposed live parts from other parts of electrical equipment. Must be trained to determine the nominal voltage of exposed live parts. C. d. All of the above. Protect yourself from electrical hazards by: Leaving covers off of electrical panels to make inspection a. easier. Wearing specialized personal protective equipment as needed. Pulling fuses instead of locking out during repairs. d. Removing the ground prong from…