Heat transfer occurs from a hot fluid, through the vessel wall, and into a cooling fluid flowing through a jacket. Neglecting the resistance of the vessel wall, derive an expression for the vessel-side heat transfer resistance divided by the total resistance to heat transfer. Neaten up your expression as much as possible

Heat transfer occurs from a hot fluid, through the vessel wall, and into a cooling fluid flowing through a jacket. Neglecting the resistance of the vessel wall, derive an expression for the vessel-side heat transfer resistance divided by the total resistance to heat transfer. Neaten up your expression as much as possible

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.61P

See similar textbooks

Similar questions

Provide two sample question regarding Heat transfer between two fluids separated by walls of a composite tube of solid materials
VI.2 A coolant is transported in a pipe with external wall temperature of -30 °C and with outer diameter of 10 cm. The tube is thermally isolated by two layers: 1) an internal layer of foamed polypropylene with thermal conductivity of 0.08 W.m.K and thickness of 10 cm, and 2) an external felt layer with thermal conductivity of 0.05 W.m.K and thickness of 5 cm. Temperature of the outer surface is 25 °C. Calculate the heat flow from the surroundings to the tube with length of 100 m. What is the temperature on the boundary between polypropylene and felt layers? Result: The heat flow from the surroundings is approx. 1.77 kW. Temperature between layers of isolation is 8.8 °C.
Please Write the differential equation which governs the heat transfer
4. A copper spherical ball (15 cm in diameter) with a density of 8933 kg/m³, specific heat capacity of 385 J/kg-K and thermal conductivity of 401 W/m-K is removed from an oven at a uniform temperature of 140 °C. The ball is then left to cool down in steady air at 20 °C. Calculate the heat transfer coefficient for this process and the time for the surface of the ball to drop to 40 °C. Use the following equation to solve this problem (characteristic dimension of the sphere is the diameter). 0.589 · Ra* Nu = 2+- 0.469 16 1+ Pr Note: you should check for the Lumped system analysis criteria for the final solution!
Problem 6. ART TAT Consider the cylindrical pipe shown in the figure. Heat is being generated in the pipe wall at a rate of R in units of W/m³, and the thermal conductivity of the wall is k, the heat transfer coefficients at the inside and outside of the pipe are h; and ho, respectively. At a given location along the pipe axis, the temperature of the fluid flowing inside of the pipe is Ti and that at the outside is To i. ii. Find the expression for the temperature distribution in the pipe wall. Find the total heat transfer rate from the pipe to both fluids.
Derive an expression for the overall heat transfer coefficient for the following case of a flat furnace wall in the x-direction. Let A= transfer area
2. Heat transfer coefficients can be difficult to measure, particularly for situations involving fast-moving fluids. In some cases however, the magnitude of the heat transfer coefficients can be estimated to a sufficient degree to enable further analysis of the larger problem. In a situation such as that described in the preceding paragraph, heat transfer occurs through the planar wall shown in the figure below. Two thermal situations are to be considered. In case I, the temperature of the fluid to the left of the wall is 130.5 °F and the fluid on the right is at 71.3 °F. Both sides of the planar wall are washed by fast- moving water. The exact values of the convective heat transfer coefficients are unknown. The heat flux through the wall is measured to be 42.6 Btu/hr-ft². 2 inches Tfl h₁ T₁ T₂ T₁² 11₂
Two inches of urethane foam will reduce heat loss close to 1000% when applied to a 2-inch diameter uninsulated steel pipe. Assume the pipe wall thickness is 0.25-inches, the pipe interior convective heat loss (hi) is 500 BTU/hr-ft2-oF, and the pipe outside convective heat loss ho 20 BTU/hr-ft2-oF, k steel is 25 BTU/hr-ft-oF, and k insulaton is 0.023 BTU/hr-ft-oF. (hint - calculate heat loss with and without insulation.
1. A composite furnace wall is made up of a 12-in. lining of magnesite refractory brick, a 5-in.thickness of 85% magnesia, and a steel casing 0.10-in. thick. Flue gas temperature is 2200 F andthe boiler room is at 80 F. Gas side film coefficient is 15 Btu/hr-sq.ft-F and air side is 4.0.Determine:a. The thermal current Q/Ab. Interface temperaturesc. Effect on thermal current and inside refractory wall temperature if the magnesia insulation weredoubled.
HEAT TRANSFER: A thick-walled nuclear coolant pipe (k = 12.5 Btu/hr-ft-°F) with 10 in. inside diameter and 12 in. outside diameter is covered with a 3 in. layer of asbestos insulation (k 0.14 = Btu/hr-ft-°F). If the inside wall temperature of the pipe is maintained at 550°F, (a) calculate the heat loss per foot of length. The outside temperature is 100°F. (b) Find the interface temperature between the pipe and the insulation.
5.8 The heat transfer coefficient for air flowing over a sphere is to be determined by observing the temperature-time history of a sphere fabricated from pure copper. The sphere, which is 12.7 mm in diameter, is at 66°C before it is inserted into an airstream having a temperature of 27°C. A thermocouple on the outer surface of the sphere indicates 55°C 69 s after the sphere is inserted into the airstream. Assume and then justify that the sphere behaves as a spacewise isothermal object and calculate the heat transfer coefficient.
A pipe carries hot molten lead from one part of a factory floor to another. The mass flow rate of lead is 0.05 kg/s. While trying to figure out the heat loss from the pipe, you found that over a 2-m length of he pipe the lead temperature drops from 580 C to 557.C. What is the rate at which thermal energy is being lost from the lead carrying pipe in this 2-m section? Use the property table to find out properties of lead as needed.