For the standardization procedure, 0.2023 g of anhydrous sodium carbonate was dissolved in 100 mt deionized water and titrated with 3.9 mL hydrochloric acid. At 25°C. a 25.00 mL aliquot of a saturated solution of borax was titrated using 7.1 mL of the standardized titrant. What is the Kp of borax at this temperature?

For the standardization procedure, 0.2023 g of anhydrous sodium carbonate was dissolved in 100 mt deionized water and titrated with 3.9 mL hydrochloric acid. At 25°C. a 25.00 mL aliquot of a saturated solution of borax was titrated using 7.1 mL of the standardized titrant. What is the Kp of borax at this temperature?

Chemistry: The Molecular Science

5th Edition

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:John W. Moore, Conrad L. Stanitski

Chapter15: Additional Aqueous Equilibria

Section: Chapter Questions

Problem 15.BCP

See similar textbooks

Similar questions

Consider the following two acids: pKa1 = 2.98; pKa2 = 13.40 HO2CCH2CH2CH2CH2CO2H Adipic acid pKa1 = 4.41; pKa2 = 5.28 In two separate experiments the pH was measured during the titration of 5.00 mmol of each acid with 0.200 M NaOH. Each experiment showed only one stoichiometric point when the data were plotted. In one experiment the stoichiometric point was at 25.00 mL added NaOH, and in the other experiment the stoichiometric point was at 50.00 mL NaOH. Explain these results.
Fifty cm3 of 1.000 M nitrous acid is titrated with 0.850 M NaOH. What is the pH of the solution (a) before any NaOH is added? (b) at half-neutralization? (c) at the equivalence point? (d) when 0.10 mL less than the volume of NaOH to reach the equivalence point is added? (e) when 0.10 mL more than the volume of NaOH to reach the equivalence point is added? (f) Use your data to construct a plot similar to that shown in Figure 14.10 (pH versus volume NaOH added).
Given three acid-base indicatorsâ€”methyl orange (end point at pH 4), bromthymol blue (end point at pH 7), and phenolphthalein (end point at pH 9)â€”which would you select for the following acid-base titrations? (a) perchloric acid with an aqueous solution of ammonia (b) nitrous acid with lithium hydroxide (c) hydrobromic acid with strontium hydroxide (d) sodium fluoride with nitric acid
5. A 300.0 mg sample containing Na,CO3, NaHCO3 and NaOH and inert material either alone or in some combination was dissolved and titrated with 0.1000 M HCI the titration required 24.41 mL to reach the phenolphthalein endpoint. And an additional 8.67 mL to reach the methyl red endpoint. Determine the composition of the sample and calculate the percent of each titrated component.
5. A 300.0 mg sample containing Na,CO3, NaHCO, and NaOH and inert material either alone or in some combination was dissolved and titrated with 0.1000 M HCI the titration required 24.41 ml to reach the phenolphthalein endpoint. And an additional 8.67 mL to reach the methyl red endpoint. Determine the composition of the sample and calculate the percent of each titrated component.
For the standardization procedure, 0.2023 g of anhydrous sodium carbonate was dissolved in 100 mt deionized water and titrated with 3.9 mL hydrochloric acid. At 25°C. a 25.00 mL aliquot of a saturated solution of borax was titrated using 7.1 mL of the standardized titrant. What is the K₁ of borax at this temperature? M 17
A 1.43 x 10-4 L solution of 45.7 mg/mL protein was analyzed using the Kjeldahl procedure. After digestion of the protein, the liberated NH3 was collected in 9.80 mL of 0235 M HCl. The unreacted acid required 10.75 mL of a standard solution of 0.0149 M NaOH for complete titration. Calculate the weight percent of nitrogen in the protein. (Molar mass N = 14.00674 g/mol)
A 1.0 g sample containing urea was dissolved in water and diluted in a 100.00 mL volumetric flask. 20.00 mL aliquot was mixed with 30.00 mL water and subjected to digestion with concentrated H2SO4. The ammonia produced is collected in 30.00 mL of 0.0500 M HCl and the excess acid is back titrated with 0.0500 M NaOH, requiring 6.80 mL. Calculate the weight percent urea [(NH2)2CO, FW=60.06 g/mol] in the sample. Please use the factor label method in answering.
3.00 g of activated charcoal was added to 50 mL of acetic acid solution (0.4 mol/L) in a conical flask. After shaking for 5 minutes, it was filtered and 25 ml of the filtrate was titrated with 0.1 mol/L NAOH using 1% Phenolphthalein indicator and the equivalence point occurred after adding about 31.40 ml of NaOH. Calculate the amount (in mg) of acetic acid absorbed (per gram of charcoal).
A 300mg sample containing Na2CO3, NaHCO3 and NaOH and inert material either alone or in some combination was dissolved and titrated with 0.1M HCl. The titration required 24.41 mL to reach the phenolphthalein endpoint. And an additional 8.67mL to reach the methyl red end point. Determine the composition of the sample and calculate the percent of each titrated component.
Titration of Ca2+ and Mg2+ in a 50.00-mL sample of hard water required 23.65 mL of 0.01205 M EDTA. A second 50.00-mL aliquot was made strongly basic with NaOH to precipitate Mg2+ as Mg(OH)2(s). The supernatant liquid was titrated with 14.53 mL of the EDTA. Calculate the concentration in ppm of CaCO3 in the sample. Calculate the concentration in ppm of MgCO3 in the sample.
A 300 mg sample containing Na2CO3, NaHCO3 and NaOH and inert material either alone or in some combination was dissolved and titrated with 0.1M HCl. The titration required 24.41 mL to reach the phenolphthalein endpoint. And an additional 8.67mL to reach the methyl red end point. Determine the composition of the sample and calculate the percent of each titrated component.