For a two-solvent recrystallization, you should have one solvent (solvent # 1) in which your desired compound is soluble at the boiling point. The second solvent (solvent # 2) should induce crystallization when added to a saturated solution of your compound in the primary solvent. According to thi statement, what was the identity of solvent #1 and solvept #2 in this experiment? O Solvent #1 was ethanol and Solvent # 2 was water O Solvent #1 was water and Solvent #2 was ethanol O Solvent #1 was hexanes and Solvent #2 was water Solvent #1 was water and Solvent #2 was hexanes

For a two-solvent recrystallization, you should have one solvent (solvent # 1) in which your desired compound is soluble at the boiling point. The second solvent (solvent # 2) should induce crystallization when added to a saturated solution of your compound in the primary solvent. According to thi statement, what was the identity of solvent #1 and solvept #2 in this experiment? O Solvent #1 was ethanol and Solvent # 2 was water O Solvent #1 was water and Solvent #2 was ethanol O Solvent #1 was hexanes and Solvent #2 was water Solvent #1 was water and Solvent #2 was hexanes

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter13: Solutions And Their Behavior

Section13.5: Colloids

Problem 1.1ACP: The blue line on the diagram illustrates the effect of using fractional distillation to separate a...

See similar textbooks

Similar questions

A 690 g of 59% strontium bromide solution is cooled from 60 oC to a certain temperature. Upon addition of around 2 g of strontium bromide, excess solute above saturation started to crystallize. Total recovered crystals is 146.003 g. At what temperature is the solution cooled?
Can a mixture of trichloromethane and propanone be separated into the pure components by fractional distillation? Explain
You have a solution that contains 4.0g of oxalic acid dissolved in 100ml of water. this solution is placed in a separatory funnel, and then 100ml of diethyl ether is added to the separatory funnel and an extraction is performed. (Diethyl ether and water are immiscible solvents.) Use the following constant to calculate how much oxalic acid is in each solvent after extraction. Solubility of Oxalic acid in water=9.5g/100ml Solubility of Oxalic acid in ether=16.9g/100ml
In the preparation of 1,200 mL of 70% alcohol from stock absolute alcohol solution, what is the volume of Diluent that must be added to the stock absolute alcohol?
in fractional distillation, how do you tell which liquid is in which fraction and which fraction has a mix of liquids if you are trying to seperate cyclohexane and toluene?? what would the density and boiling point of the first fraction be
The followings methods are useful to induce crystallization EXCEPT adding a small crystal of the desired compound, called a seed crystal, to the solution adding anhydrous potassium carbonate to the solution and cooling it in an ice bath scratching the inner wall of the Erlenmeyer flask with a glass stirring rod reheating the solution to boiling to boil off some of the solvent, and then allow the solution to cool to room temperature again to effect crystallization
5- A chemist is given a nonelectrolyte white powder for analysis. 38.7 g of this substance is dissolved in 100.0 g of water. It is determined that the resulting solution freezes at -4.0°C. Additionally, the elemental composition of the substance is identified and found to be 40.0% C, 6.7% H and 53.3 % O by mass. Find the molecular formula of this unknown white powder using these experimental evidences (Kş of water: 1.86°C/m, C: 12 g/mol, H: 1 g/mol, O: 16 g/mol).
A 690 g of 59% strontium bromide solution is cooled from 60 oC to a certain temperature. Upon addition of around 2 g of strontium bromide, excess solute above saturation started to crystallize. Total recovered crystals is 146.003 g. How many solute is initially dissolved?
Students were tasked to conduct a recrystallization experiment to test the ability of the newly discovered solvents in their laboratory to purify and separate a mixture containing compounds X and Y. The solubility of the two compounds in g/50 mL of hot and cold solvents are given by the photo.
Your compound exhibits the following solubility behavior (S = soluble, P partially soluble, I = insoluble). Whic solvent is the best choice for recrystallization? Solvent water heptane diethyl ether decane dichloromethane b.p (°C) 100 98 35 174 40 hot solvent 1. cold solvent O decane heptane )dichloromethane water diethyl ether
12 g of unknown organic sample was dissolve in 706 mL of Dicloromethane (DCM). The boiling point of benzene was increased by 2.72oC. Determine the molecular weight of the unknown sample? Kb of DCM = 2.42oC/m Bb of benzene = 39.6 oC density of benzene = 1.33 g/mL at 25 °C Round your answer to the nearest whole number, no units required.
Pre-lab Assignment 1.) Note from the 'Introduction' that the freezing-point-depression constant, Kfp, for any solvent can be calculated as long as the heat of fusion, AHfus, and freezing point of the solvent is known. Calculate the freezing-point-depression constant (in SI units) for carbon tetrachloride, CC14, given that its heat of fusion is 2.5 kJ/mol and its freezing point is 250.3 K. M solvent & (TF Solvet) AIFUD - molor Mod 1=0,0821 LATM/ molk ~14=153.82glangs Кы = latm (153.82 $7) (0.0821 (ar) (250.5x)² 2 2.5 123/M/G\