following figure shows the one-line diagram of a power system. Bus 1 is selected as a reference bus (slack bus), and bus 2 is load bus. Using the Gauss-Seidel method, determine the value of the voltage at the load bus 2 and perform two iteration. Moreover determine the complex power flow at bus 1 and also active and reactive power in transmission line. The line impedance on a base of 100 MVA. Use an initial estimate of Vº =1+ j(0) . Z12 = 0.02 + j0.04 2 S2 = 280 MW +j60 Mvar %3D

following figure shows the one-line diagram of a power system. Bus 1 is selected as a reference bus (slack bus), and bus 2 is load bus. Using the Gauss-Seidel method, determine the value of the voltage at the load bus 2 and perform two iteration. Moreover determine the complex power flow at bus 1 and also active and reactive power in transmission line. The line impedance on a base of 100 MVA. Use an initial estimate of Vº =1+ j(0) . Z12 = 0.02 + j0.04 2 S2 = 280 MW +j60 Mvar %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on the diagram. Line impedances are marked in per unit on 100 MVA base and the line charging susceptances are neglected. a) Using Gauss-Seidel Method, determine the phasor values of the voltage at load bus 2 and 3 according to second iteration results. b) Find slack bus real and reactive power according to second iteration results. c) Determine line flows and line losses according to second iteration results. d) Construct a power flow according to second iteration results. Slack Bus = 1.04.20° 0.025+j0.045 0.015+j0.035 0.012+j0,03 3 |2 134.8 MW 251.9 MW 42.5 MVAR 108.6 MVAR
A loss less TiL with characteristic impedance of to is terminated in Zr=3Z0. use crank diagram to sketch the voltage versus distance from the load, (Assume vst = 1 volt). @ Repeat the above How for Zv=Zo/3-
Q4(b) The equivalent circuit of a single phase short transmission line is shown in Figure Q4(b). Here, the total line resistance and inductance are shown as lumped instead of being distributed. i) Sketch the phasor diagram and assess with by labeling the details for the A.C. series circuit shown in Figure Q4(b) for the lagging power factor at load point (Vn). ii) Summarize, what if the load change from low value to high value shown in Figure Q4(b). R XL el Vs Vn Figure Q4(b) Load
A network consisting of a set of generator and load buses is to be modeled with a DC power flow, for the sake of conducting a contingency analysis. The initial flows calculated with the DC power flow give the following information: f°2-4 = - 65.3 MW and fº4-5 = 13.6 MW. The following values of LODF and PTDF factors are given: PTDF54,2-4 = -0.2609, LODF2-4,4-5 = -0.6087. Calculate the contingency flow on line 2-4 due to outage of line 4-5. Select one: O a. -75.5MW O b. None of these O c. -68.85MW O d. -73.58MW O e. 75.5MW O f. -61.75MW
What is load curve
In the power system network shown in Figurebelowbus 1 is a slack bus with V = 1.020° per unit and bus 2 is a load bus with S2 300 MW + 80 Mvar. The line impedance on a base of 100 MVA is Z = 0.01 + j0.02 per %3D unit. (a) Using Gauss-Seidel method, determine V. Use an initial estimate of = 1.0 + j0.0 and perform two iterations. i.e.Deternine(a)V2 and (b)V½? Z12 = 0.01+ j0.0 2 2 S2 300 MW+80 Mvar (a) 0.954 - j0.052 (b) 0.949 - j0.0517 (a) 0.914 - j0.0152 (b) 0.949 - j0.0517 (a) 0.945 - j0.025 (b) 0.994- j0.0571 (a) 0.965 - j0.0255 (b) 0.914 - j0.0529
please solve for nodal stress method. (if it is possible to apply supernodes)
The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S-15.93 MW-j33.4 Mvar, and at bus 3 is S3-77 MW+j14 Mvar. It is required to hold the voltage at bus 3 at...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu $₂ Figure V3
The equivalent circuit of a single phase short transmission line is shown in Figure Q4 (b). Here, the total line resistance and inductance are shown as lumped instead of being distributed. i) Sketch the phasor diagram and assess with by labeling the details for the A.C. series circuit shown in Figure Q4 (b) for the lagging power factor at load point (Vn). ii) Summarize, the impact of voltage regulation and efficiency, if the line resistance and line increases are doubled Figure Q4(b). R XL Vs Vn Figure Q4(b) Load
in distribution transformers; What is 30 degrees phase shift in delta-star connection? What are the disadvantages? (can you explain with drawing?)
The Gauss-Seidel is an iterative method used to solve a set of nonlinear equations in the power flow. For the power network shown in Figure below, bus 1 is a slack/swing bus with V1 =1.0 L per unit and bus 2 is a load bus with P2 = 280 MW and Q2 = 60 MVar. The line impedance on a base of 100 MVA is Z = 0.02 +j0.04 per unit. Using Gauss-Seidel method, show how you determine V2 (first iteration only), and the power loss in line 1-2. Use an initial estimate of per unit but do not need to solve them numerically. After four iterations the voltage at bus 2 converges to per unit. Z12=0.02+j0.04 PL
At the end of the 8 km overhead line given in the figure below, there are two distribution transformers, one of which is 800kVA and the other is 1200kVA, operated with power coefficients of 0.6 and 0.8, respectively. The end-of-line voltage is 6kV. Find the required rated cross section and line head voltage so that the power loss on the line is less than %pk = 10.