Find the currents (in A) flowing in the circuit in the figure. (Indicate the direction with the sign of your answer. Due to the nature of this problem, do not use rounded intermediate values in your calculations-including answers submitted in WebAssign.) E, = 24.0 V b. 0.10 2 R, 5.0 Ω Eg = 48.0 V 17 Q R, k a 0.50 2 44 Q 20.20 2 R 82 0 E4 = 36.0 V Eg = 6.0 V i 0.05 2 h I = A I, = I, = A.

Find the currents (in A) flowing in the circuit in the figure. (Indicate the direction with the sign of your answer. Due to the nature of this problem, do not use rounded intermediate values in your calculations-including answers submitted in WebAssign.) E, = 24.0 V b. 0.10 2 R, 5.0 Ω Eg = 48.0 V 17 Q R, k a 0.50 2 44 Q 20.20 2 R 82 0 E4 = 36.0 V Eg = 6.0 V i 0.05 2 h I = A I, = I, = A.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter9: Current And Resistance

Section: Chapter Questions

Problem 28P: An aluminum wire 1.628 mm in diameter (14-gauge) carries a current of 3.00 amps, (a) What is the...

See similar textbooks

Similar questions

Q1. a) Using mesh analysis, find 1₁ and 12 in the circuit of Figure1. j10Ω 40/30° V (+ -j20 2= 40 92 1₂ 50/0°V Figure1 b) Verify the answers of 1₁ and 1₂ obtained in part a by using multisim simulation. (Screenshot of the circuit in multisim simulation with the values of 1₁ and 12 are required).
Two resistors of resistance 230 O and 340 O are connected in series (one after the other). A potential difference of 20 V is applied between the ends of the chain. a)What is the total resistance of the circuit (in O)? Give your answer as a whole number. b)Calculate the current flowing through the circuit (in A). Gve your answer to 3 d.p. and use this value to that degree of accuracy, in subsequent calculations, if needed. c)Calculate the potential difference across the 230 O resistance. Give your answer in volts to 2 d.p..
Consider the circuit shown in the figure below, where R, = 8.00 N, R, = 7.00 N, and Ɛ = 11.0 V. %3D 10.0 N R2 5.00 N 2.00 N R1 (a) Find the voltage (in V) across R,. V (b) Find the current (in A) in R,. A
ostro Imssb1.mutah.edu.jo/r A conductor has a cross-sectional area of 2.3x 10-6 m2 and the number of free electrons per unit volume is 8.5x 1028 electron/m. When the current is 9 A, find the drift speed (in mm/s) of the electrons. Use the charge of the electron to be 1.6x 10-19 C
A 2 0 resistor, a 10 N resistor, and a 15 N resistor are connected in parallel across a 12 V battery. Determine the equivalent resistance for the circuit. Answer in units of N. 026 (part 2 of 2) . b) Determine the current in the circuit. Answer in units of A.
3:08 l LTE Youngstown State University Edit Friday 9:58 AM 1. A conductor of radius r, length l and resistivity p has resistance R. It is melted down and formed into a new conductor, also cylindrical, with one fourth the length of the original conductor. What is the resistance of the new conductor? (Hint: the volume stays the same) 16R a. b. 4R c. 1. d. 4 iR 16R e.
A current of I = 4.7 A passes through the circuit shown, where R = 46 Q. I 3R 5R ww ww 2R 6R §2RR ww 10R 5R A. In terms of R, I, and numeric values, write an expression for the voltage of the source, V. B. What is the voltage, V in volts?
Two resistors R1 = 6 N and R2 = 12 Q are connected in parallel to each other and in series to R3 = 2 Q. An ammeter measures an electric current of 3 A flowing though resistor R3. What is the net voltage applied to the circuit? R4 ... Rg (A R2 A A. 6 V B. 12 V C. 18 V D D. 24 V E Е. 36 V
Three resistors, R1= 30 Ω, R2= 77 Ω, and R3=R, are connected in parallel with a 12 V battery. A) The total current flowing through the battery is 0.88 A. Find the value of resistance R. Express your answer using two significant figures. B) Find the current through each resistor. Enter your answers numerically separated by commas. Express your answers using two significant figures.
Find the resistance(in the unit of Ohm) of a Nichrome rod of diameter d=1 mm and has a length L=5 m (resistivity of Nichrome, p = 1.8x 10-º0.m) a. 0.0001312 b. 0.02291 c. 0.107 d. None e. 0.01146
A piece of wire of length 31.5 cm and cross-sectional area 227.4 cm² is made into a resistor of resistance 713.8 ohm. What is the resistivity of the material used to create the resistor? O a. 5113020.78 ohm-metre O b. 10.04 ohm-metre O c. 5152.96 ohm-metre d. 98.88 ohm-metre Oe. 51.53 ohm-metre Of. 515295.62 ohm-metre O g. 0.10 ohm-metre Oh. 0.99 ohm-metre
if possible, please write on paper and upload photo of paper. Other forms of answers do not show for me. Two conductors are made of the same material and have the same length. Conductor A is a solid wire of diameter 1.3 mm. Conductor B is a hollow tube of outside diameter 7.1 mm and inside diameter 6.1 mm. What is the resistance ratio RA/RB , measured between their ends?