Figure 1 below illustrates a circuit represented in the frequency domain using phasors and impedances. The input to the AC circuit is a source voltage v,(t) with amplitude of 12 V , anglular frequency 10 rad/s, and phase angle of 0°. Thus the phasor corresponding to the given v,(t) is respectively described as V,(w) = 1220°. The impedances corresponding to each circuit element are: ZR, (w) = 40 , Zr,(w) = 160, Z1,(w) = j20 N, ZĻ̟(w) = j25 N, Zc(w) = -j14N 40 j20 N -j14 0 1220°( (@) 160 j25 N

Figure 1 below illustrates a circuit represented in the frequency domain using phasors and impedances. The input to the AC circuit is a source voltage v,(t) with amplitude of 12 V , anglular frequency 10 rad/s, and phase angle of 0°. Thus the phasor corresponding to the given v,(t) is respectively described as V,(w) = 1220°. The impedances corresponding to each circuit element are: ZR, (w) = 40 , Zr,(w) = 160, Z1,(w) = j20 N, ZĻ̟(w) = j25 N, Zc(w) = -j14N 40 j20 N -j14 0 1220°( (@) 160 j25 N

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The following is given for a series R-L-C circuit: resistor (R) = 8 Ohms, an inductor (L) = 32 mH and a capacitor (C) = 800uF. The circuit is supplied by a voltage source of e = 120 sin (125t) Volts. What is the angular frequency of the ac source? What is the period of ac source? What is the circuit impedance? What is the power factor? What is the real power of the circuit? What is the rms value of the circuit current?
A series RC circuit with R=4k ohms and C= 0.40 mF is connected to an AC voltage source e(t)= 100 sin200t. Determine the following: a). The overall power factor ( indicate big leading or lagging) b). The voltage drop across the resistor and the capacitor
The following is given for a series R-L-C circuit: resistor (R) = 8 Ohms, an inductor (L) = 32 mH and a capacitor (C) = 800uF. The circuit is supplied by a voltage source of e = 120 sin (125t) Volts. What is the angular frequency of the ac source? What is the circuit impedance? What is the power factor? What is the real power of the circuit?
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (I, in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1. and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. If the value of R2 =1600 Ohm then the input voltage (in volts) is: 7.5 25 110 Frequency H2 O a. 4 O b. 16 sin(9888 t) O c. 8 O d. 8 cos(6.28 f t) O e. 8 sin (6.28 R t)
If the phasor current is 45 degrees ahead of the phasor voltage, write down all the possibilities about circuit impedance.
From the provided AC voltages add them together by transforming them into phasors. You must express the final result as a sinsoid within a time domain with their accomping phase angles in radians. All complex math must also be shown.
Phasors 1.) Transform the following sinusoids to phasors: (a) - 10 cos(4t+ 75) (b) 5 sin(20t – 10°) (c) 4 cos 2t + 3 sin 2t
Consider a sinusoidal emf source, v(t) = Vm sin (@t) results of current of i(t) = Im sin (@t+0) is applied to circuit of R, L & C in series. How to find the voltage across each one?.
3. A sinusoidal voltage is applied to the circuit below. Determine the following: I, Irms, lavg, Ip- 1.0 kN
4) Given: R = 700-N, Xc = - j 500-N, e(t) = 150 sin(wt) V Find: a) Total impedance of the ckt. b) Total current in phasor and sinusoidal form c) Voltage drop across the resistor and capacitor in phasor and sinusoidal form d) Total Power and Power factor
In alternating current, AC, theory, the voltage through an inductor leads the current by a phase angle of 90°. Complex numbers can help in this situation as when a real number is multiplied by i it rotates through 90° on the Argand diagram, with the magnitude remaining the same. This allows us to specify the impedance through an inductor as a complex number. This can be combined with a resistor to give a combined impedance of z = r + Li. If we have two such elements in a circuit, we can use complex numbers to determine the total impedance when they are in series and in parallel. In series Zt = Z1 + Z2 In Parallel Add the following two impedances (a) in series and (b) in parallel. Z1 = 4 + 3i and Z2 = 12 + 5i
In alternating current, AC, theory, the voltage through an inductor leads the current by a phase angle of 90°. Complex numbers can help in this situation as when a real number is multiplied by i it rotates through 90° on the Argand diagram, with the magnitude remaining the same. This allows us to specify the impedance through an inductor as a complex number. This can be combined with a resistor to give a combined impedance of z = r + Li. If we have two such elements in a circuit, we can use complex numbers to determine the total impedance when they are in series and in parallel. In series Zt = Z1 + Z2 In Parallel