Humng Figure0,75 m0.75 m2.5 m3 mFR 12.5 m0.75 m213 m0.75 m30 kN90 KN| 20 kN< 1 of 1▼Part AIf F₁ = 30 kN and FB = 35 kN, determine the magnitude of the resultant force(Figure 1).Express your answer with the appropriate units.FR =SubmitPart Bx, y =ODiSubmitμAValueRequest AnswerSpecify the location of its point of application (x, y) on the slab.Enter your answers numerically separated by a comma.——| ΑΣΦ ↓1Request AnswerPUnitsvec?www?m

Figure 0.75 m X 0.75 m 2.5 m 3 m FB 12.5 m 0.75 m 10 3 m Z 30 kN 90 kN FA | 20 kN 1 of 1 If FA = 30 kN and FB = 35 kN, determine the magnitude of the resultant force(Figure 1). Express your answer with the appropriate units. FR = Value Submit Part B μÀ x, y= Submit Request Answer Specify the location of its point of application (x, y) on the slab. Enter your answers numerically separated by a comma. IVE| ΑΣΦ | 41 Units Request Answer ? vec ? m

Figure 0.75 m X 0.75 m 2.5 m 3 m FB 12.5 m 0.75 m 10 3 m Z 30 kN 90 kN FA | 20 kN 1 of 1 If FA = 30 kN and FB = 35 kN, determine the magnitude of the resultant force(Figure 1). Express your answer with the appropriate units. FR = Value Submit Part B μÀ x, y= Submit Request Answer Specify the location of its point of application (x, y) on the slab. Enter your answers numerically separated by a comma. IVE| ΑΣΦ | 41 Units Request Answer ? vec ? m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Replace the loading by an equivalent resultant force. (Eigure 1) Suppose that wy -20 lb/ft, w₂=5 lb/ft, and F= 70 lb Figure 98 € 50 1 of 1 > Y Determine the magnitude of the resultant force Express your answer in pounds to three significant figures. FR= Submit Part B d= VG ΑΣΦ Submit Specify the location of the force on the beam, measured from A Express your answer in feet to three significant figures. Request Answer Ivec 195] ΑΣΦ IT Request Answer vec GWD ? ft ? lb
Replace the distributed loading shown in (Eigure 1) by an equivalent resultant force. Suppose that w=3.5 kN/m and ₂-2.5 kN/m Figure 1 of 1 > Part A Determine the magnitude of the resultant force Express your answer to three significant figures and include the appropriate units. FR = Submit Part B Value Request Answer Units Determine the direction angle of the resultant force measured counterclockwise from the negative z direction Express your answer in degrees to three significant figures.
Required information Determine the magnitude and direction of each force. In the figure shown, a=7 in and F= 100 lbf. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. B F -10 in 10 in- +10 in- What are the values of forces at points A and Bin Ibf? | Ibf RAX RBx RAy RBy Ibf Ibf Ibf
Determine the magnitude of the resultant force. Replace the three forces acting on the shaft by a single resultant force. Suppose that F = 650 lb, F = 400 lb , and F3 = 260 lb. (Figure 1) Express your answer to three significant figures and include the appropriate units. ? HA FR = Value Units Submit Request Answer Part B Figure < 1 of 1 Determine the angle between the resultant force and the x axis. Express your answer using three significant figures. vec ? 5 ft 3 ft -- 2 ft 4 ft measured counterclockwise B from the negative x axis 1213 5 Submit Request Answer F2 Part C Specify where the force acts, measured from end B.
Determine the Resultant Force, its magnitude and direction of the given co-planar, Space tensile force cables as shown in the diagram below. AB = 100lbs; AC = 80 Ibs & AD= 90 Ibs. Please answer in COMPLETE solution. *3 decimal places all answer.
In your response, please display the full computation and all FBDs that were used. Only round off at the final answer with 4 decimal places. P=2kN, F=3kN, and moment M=0.5kN-m are acting on the structure in the illustration. A pin at Z and a cable RQ connected by a connecting pin R support it. Im ● F ● P S TO M Im R lu W OZ a' 0.8m 3m If the pin support Z's factor of safety against shear stress is 3, determine whether a single or double shear should be provided for an economical and safe design. 4 m The mas allowable shear stress in the pin is 50MPa. Consider the following specifications. Single shear design: 25mm pin diameter Double shear design: 17mm pin diameter
Q1/ Two Forces Shown in Fig. (1) acts on the bracket, determine the effect of these two forces (using Parallelogram method). 100 F₂ = 150N F₁ - 200 N
The beam is supported by rods AB and CD that have different cross-sectional areas. The area of rod AB is AAB = 10 mm² .The area of rod CD is Acp = 8.25 mm². B F₁ Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value F₁ d₁ d₂ NAB= 5050 N 3.25 mm 0.5 mm a. Determine the magnitude of the normal internal force in rod CD, NCD. b. Determine the magnitude of the normal internal force in rod AB, NAB. c. Determine the normal stress in rod CD, OCD. d. Determine the normal stress in rod AB, O AB. Round your final answers to 3 significant digits/figures. NCD = N N
The force acting on the gear tooth is F = 30 lb. Resolve this force into two components acting along the lines aa and bb.(Figure 1) Figure F 60° a 80°- b b 1 of 1 Determine Fa Express your answer to two significant figures and include the appropriate units. F₁ = 26 HA lb ? Determine Ft. Express your answer to two significant figures and include the appropriate units.
ASAP
Consider the bracket shown in Fig-1. If: F1 = 10 N@ 120° • F2 = 75 N@ -90° then, what is the direction of the resultant force on the bracket? 176° 4.31° -4.31° 2.17° -176° -2.17° 94.3° -94.3°
> shown. The distributed load acts on the shaft as shown. Suppose that a = 0.7 ft. (Figure 1) Figure w = (2x - 8x + 18) lb/ft 10 lb/ft 201 -2 ft 1 of 1 18 lb/ft B ▼ Determine the magnitude of the equivalent resultant force. Express your answer to three significant figures and include the appropriate units. FR = Submit Part B 0 d= μÀ Value Request Answer h μA Specify the location of the resultant force, measured from the support A. Express your answer to three significant figures and include the appropriate units. Value Units P Pearson PSMK ? Units SAM ?