F.) A residential air conditioning unit with an SEER of 14 serves a single-detached family residence in Quezon City, Philippines having an annual cooling load hours of 6,116 hours. The total cooling load is 36,000 Btu/hr. Calculate the approximate annual energy consumption of the A/C unit

F.) A residential air conditioning unit with an SEER of 14 serves a single-detached family residence in Quezon City, Philippines having an annual cooling load hours of 6,116 hours. The total cooling load is 36,000 Btu/hr. Calculate the approximate annual energy consumption of the A/C unit

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Related questions

Q: The reliability of the 3- hop microwave system is successively decremented by 0.01%. Find the outage…

A: Given: A 3- hop microwave system having Reliability of the first hop, RA=99.99%=0.9999 The…

Q: A 25V, 2.5kHz supply is connected to a network comprising a variable capacitor in parallel with a…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: R1 1000 V1 C1 =1µF 12Vpk 1kHz 0° Find the capacitor's reactance Xc, impedance Z, the circuit's…

A: To find the capacitive reactance and total impedance and current and voltage across the resistor

Q: A wind turbine is installed, the speed of the wind is 9.6 m/s, the pressure is 1 atm and the…

A: For the given data wind power density is determined as shown below

Q: Iraq has a potential source of solar energy according to high light irradiance for long hours, as…

Q: Problem 10. A coil consists of a resistance of 100 2 and an inductance of 200 mH. If an alternating…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: 17. What is the share of renewable energies on the total electrical energy generated for 2019/2020?…

A: Introduction:. Electricity is produced using all sources of renewable energy. Geothermal steam is…

Q: CHIS Q1. Evaluate the intensity of solar radiation for 15 March 2019, given solar constant (Isc) =…

Q: A diesel power station supplies the following loads to various consumers: Industrial consumer = 1000…

A: Industrial consumer = 1000 kW Commercial/Business Consumer= 750 kW Domestic Power (Heater, A/C etc)=…

Q: A three-conductor belted cable 15 mi long is used as a three-phase underground line for a 69 kV…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Maria Cristina falls located at south has a height of 100 meters, it discharges at constant rate 2.5…

Q: A radio transmitter is connected to an antenna having an impedance 60 + j20 N with a 50 N coaxial…

A: This question belongs to electronics . It is based on the calculation of power for antenna .…

Q: A factory operates at 0.80 p.f. lagging and has a monthly demand of 750 kVA. The monthly power rate…

A: Given data, The value monthly demand is Pm = 750 KVA. The value of power factor is cosϕ = 0.8. The…

Q: Perform the following operations, including phasor diagrams where appropriate.

A: In this question we will perform given operations......

Q: 2. A manufacturer quotes a maximum VSWR of 1.07 for a resistive load when it is used to terminate a…

A: In this answer we will try to find what percentage of the incident power is the reflected power by…

Q: Tek Tektronix TBS 1052B-EDU Digital Oscilloscope 1.00V M 100us Station 2 Toaching M.Pos: 0.000s…

Q: Derive the equation for maximum power transfer, Pmax= E V / X.

Q: (+2 100 90 80 70 R1 Mwmn 50 Q 10mH V1 220 Vrms 60 Hz 0° Capacitance Real Power (UF) (Watts) 60…

A: The given circuit is shown below. A table is shown below. Write an essay on average power and…

Q: Q.4 Answer any One of the following A. Two microstrip transmission lines A and B are to be used in a…

A: Given: for transmission line A, wh=0.34εr=4 for transmission line B, wh=0.9εr=2

Q: A SERIES RC CIRCUIT TAKES A CURRENT WHOSE EQUATION Is 2 sin (754t+40) AMPERE. WHEN CONNECTED TO A…

Q: A room 20 m by 10 m is to be illuminated by 10 lamps at an average illumination of 50 lux. If CU =…

A: Given Room L=20 mB=10 mNo.of lampsN=10illumination E=50 luxcoefficient of utilization…

Q: Define Five of the following Heliostats, Primary energy, capacity factor, commercial energ;…

A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.

Q: - An electrical motor is modelled as 5117j ohm. Then a 300 pF capacitor is conneeted in parallel. If…

A: we need to find the total current, active power, reactive power and apparent power and also the…

Q: 3.10 The earth is 146.9 million km from the sun, and receives light with an intensity of 1.36 kW/m2.…

A: It is given that: Earth distance from sun is 146.9 million kmIntensity of sunlight for earth is 1.36…

Q: An open–wire transmission line is made from two wires, each with a diameter of 2 mm, located 20 mm…

A: In this question we will find characteristic impedance of open wire transmission line....

Q: load of the persons and infiltration in the room are 5100 W and 3400 W respectively; the air is 1250…

Q: Many have witnessed the use of an electrical megaphone for amplification of speech to a crowd. A…

Q: Which among the following component will not be affected, if outage magnitude increases? a.…

A: Need to find the correct option

Q: A single-phase 60 miles 69kV transmission line consist of two 000-AWG solid copper conductors spaced…

A: In this question we need to find a capacitance of the given transmission line.

Q: A 397-Vrms, 60-Hz supply serves a load that is 10 kW (resistive), 5 kVAR (capacitive), and 15 kVAR…

Q: . Acoil having an impedance of (8 + j6) Nis connected across a 200-V supply. Express the current in…

Q: It is planned to install an off-grid photovoltaic system in a residence. For this planning The…

A: Given data is - A1=In the winter season appliances power demand= 3.5 kWh/m2/dayA2=In the summer…

Q: Problem 1 Businessman Lance Smile own two large malls in Basilan Island. Both malls are connected in…

A: Given,Operating voltage,V=13.8kVrmsImpedance,Z=1+j2.5ΩFor mall 1,P1=400kWcosθ1=0.8 laggingFor mall…

Q: For the volume from grids of spot heights, compute the Eh1 of the below ground elevation, if you…

A: Solution formation level base height (F.L - B.H)=h 85.67 83.81 1.8 86.22 83.81 2.35 87.34…

Q: Problem 1 Businessman Lance Smile own two large malls in Basilan Island. Both malls are connected in…

A: A closed path, where electric current can flow defined as an electric circuit. It is various…

Q: Calculate the cost of generation per KWh for a power station having the following data Installed…

A: It is given that: Installed capacity of the plant=200 MWCapital cost=Rs. 400 croresRate of interest…

Q: Q2.) For an AM Radio channel, calculate the power efficiency of this system when the carrier…

Q: A coaxial cable of 105 Q impedance is used to connect a satellite receiving antenna to the decoder.…

A: Given, The impedance of the coaxial cable is 105Ω. Capacitance (C)=75 pF/m = 75×10-12 F/m Diameter…

Q: Que the generalised ckb. constants of th are A = B 0.93 7j0·016. 20+ 140. the lead at the rece 0.8…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Do All the subpart of given question.. A 765kV circuit has flat horizontal spacing of 10ft between…

A: Given Horizontal spacingD=10 ft Th spacing between each conductor S=1 ft The diameter of the…

Q: 1. A wind turbine supplies an effective power output of 1.8 MW to a grid. Determine the power…

A: The solution can be achieved as follows.

Q: Derive the Yelationship ICEO=(1tB) ICBO

Q: What is the instantaneous current at t=1 sec, if a 20 micro-farad capacitor was charged with 10…

A: It is given that: C=20 μFE=10cos2377tt=1 sec

Q: A string of four suspension insulators is connected across a 285 kV line. The self-capacitance of…

Q: Electrical transmission towers are stationed at 350 m intervals and a conducting cable 2 cm in…

A: Electrical transmission towers are stationed at 350 m intervals and a conducting cable 2cm in…

Q: A PV system delivers power to a DC motor that in turn feeds a water pump. The DC motor is rated for…

A: The given data is, Power of the DC motor, P = 1 kW Motor efficiency, n = 85 % Number of solar cells…

Q: Given a windfarm site with 500-meter elevation, 8 m/s average wind speed, and average temperature of…

A: A windfarm site has 500-meter elevation, 8 m/s average wind speed, and average temperature of 27°C.…

Q: The FCC has designated a 20-MHz range of frequencies ranging from 88 MHz to 107 MHz to the…

A: FCC(Federal communications commission) which regulates the international communication. FCC allocate…

Q: A power station supplies the following loads to various consumers: Industrial consumer = 1500kW…

Concept explainers

Electrical Heating Unit

The conversion of electrical energy to heat energy is known as electric heating. The heating system that converts the electrical energy to heat energy for various application is called electrical heating unit. Electricity is employed as the firing mechanism in electric heating systems, which transforms electric current to heat. Electric heaters have heating elements in the form of electric resistors.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. a) Explain the terms load factor and diversity factor. b) Discuss the advantages of interconnected grid system. c) A generating station is to supply four regions of load whose peak loads are 10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Calculate: (i) the maximum demand on the station, (ii) annual energy supplied by the station and (iii) suggest the installed capacity and the number of units.
A wind energy system has been designed for 20 years of operation. The designed system has a wind turbine of power 600 kW which costs is $450,000. Estimate the Levelized cost of electricity generated by this wind energy system. (Capacity factor: 28.54%)
In a string of three identical suspension insulator units supporting transmission line conductor.if the self capacitance of each unit is debited as C farads, The capacitance of each connector pin to ground can be taken as 0.1C farad's. If the maximum permissible voltage per unit is given as 20 kva then calculate A.maximum safe working voltage B.string efficiency
6. If a power system has 10,000 kVA capacity, operating at 0.7 lagging power factor and cost of synchronous capacitors to correct the p.f is $10.5/kVA.Determine the cost involved and also required leading reactive power to increase the power factor to (a) 0.85 lagging p.f
Discuss the concept of a smart grid and how it improves the efficiency and reliability of power systems.
B) Four regions of peak loads 5 MW, 7 MW, 8 MW and 10 MW are supplied by a generating station. The average annual load factor is 0.6 and the diversity factor at the station is 1.5. Calculate: (i) Annual energy supplied by the station (ii) The maximum demand on the station. (iii) If the installed capacity is greater than maximum demand by 20%, suggest the best number of units should be used to cover the load curve
A generating station has a maximum demand of 20 MW, a load factor of 60%, a plant capacity factor of 48% and a plant use factor of 80% Find: 1)the daily energy produced (2) the reserve capacity of the plant. (3) The maximum energy that could be produced daily if the plant was ruinining all the time.(4).Maximum energy that could be produced daily if the plant was running fully loaded and according to an operating schedule.
A 15kVA, 440V, single-phase alternator draws a field current of 5A at rated load. With the same field current, the open circuit emf and short-circuit current are 100V and 80A respectively. The ohmic resistance of the armature between terminals is 0.12 ohm. The ratio of effective to ohmic resistance maybe taken as 1.1. Determine the voltage regulation (in %) when the load is purely resistive.
3. A yearly load duration curve of a gas turbine power plant is a straight line from 50,000 to 5,000 kW. The load is taken by a power plant that consists of two units of 30,000 kW each and one unit of 20,000 kW. Determine: (a) Installed capacity (b) Plant factor (c) Maximum demand (d) load factor and (e) utilization factor of the plant.
As shown in Figure, Erycner and Kuscu proposed a hybrid transpired solar chimney consisting of solar panels and transpired solar collectors. A prototype for this category has been constructed at Trakya University in Edirne-Turkey in 2018. The characterizes of the plant are; • Chimney height is 55 m, Solar Collector diameter is 30 m Solar energy conversion efficiency into electricity by chimney turbine is 20% • PV array area occupation 40% from solar collector area. PV module, V max 12 v, I max 4 A and Voc = 14 v, I sc = 5 A According to this information. Find at solar radiation 1000 w/ m² 1- Plant electrical generated 2- PV array efficiency 3- PV, Fill factor Glass Panel PV Panel
A 100MW hydro-electric station is supplying full load for 10 hours in a day. The water is supplied from a reservoir of 1km2 surface area. Calculate the reduction in the water level of the reservoir in one day. Assume effective head of water as 200 m and efficiency of the the station is 80%.
For a single phase ac voltage controller/chopper, which is designed by using thyristors, with the series R (=8[Ohm]) and L(=30 [mH]) load, if the rms value of the current flowing through each thyristor in the chopper circuit is equal to 2.83[A], then calculate average power absorbed by the load. O 120.5604 W O 288.3204 W O 64.8529 W O 91.3782 W O 128.1424 W O 187.5384 W O 38.5784W O 52.3564 W