(f) Calculate the total impedance (magnitude and angle) and current / from the nameplate value of the inductance and the measured resistor value. Ignore the effect of R, Enter the results in the second column of Table 8.2. Calculation: 10 kHz E=8V (p-p) 000 10 mH R measured R 1 ΚΩ = Channel 1 Vert.: 1 V/div. Hor.: 20 μs/div. Channel 2 Vert.: 1 V/div. Hor.: 20 μs/div.

(f) Calculate the total impedance (magnitude and angle) and current / from the nameplate value of the inductance and the measured resistor value. Ignore the effect of R, Enter the results in the second column of Table 8.2. Calculation: 10 kHz E=8V (p-p) 000 10 mH R measured R 1 ΚΩ = Channel 1 Vert.: 1 V/div. Hor.: 20 μs/div. Channel 2 Vert.: 1 V/div. Hor.: 20 μs/div.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 4PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

1. Enumerate five formulas for five series connected inductances across Vt source and draw the circuit. 2. Enumerate five formulas for five parallel connected inductances across Vt source and draw the circuit.
8. Liquids with solid impurities a) Have higher dielectric strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average de voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35
In a series circuit with the following devices to a 230volts 60Hz supply with a resistor in the range of 300 ohms and 990 ohms. What are the steps in calculating the impedance ...
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
Which of the following is true about all series ac circuits?(a) The voltage across any circuit element is a maximumwhen the current is a maximum in that circuit element.(b) The current at any point in the circuit is always thesame as the current at any other point in the circuit.(c) The current in the circuit is a maximum when thesource ac voltage is a maximum.(d) Resistors, capacitors, and inductors can all change thephase of the current.
A series circuit consists of a 66.4 microfarad capacitor and variable resistor. For what two values of resistance will the power taken by the circuit be 172. 8 W, if the impressed 60 Hz emf is 120 V?
a. individal current b. voltage source
For the network shown in figure (3), if the switch is closed for 2usec and then opened for Susec, find mathematical expressions for vi and in of both periods of time and then plot the waveforms of vL and i as a function of time.
Question 8. What is the total inductance of a circuit containing three 5h inductors connected in series? A. 5h. B. C. D. 15 h. 1.67 h. 10 h.
1.Enumerate five formulas for series-parallel connected inductances and draw the circuit. 2.Enumerate five formulas for parallel-series connected inductances and draw the circuit.
TOE This is a photo of a capacitor that corrects the power factor in an AC setup, in DC it is used in electronic board for appliances and other small devices. Tell me something about this photo.
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4