Example #5: The RC DIS-Charging Circuit The circuit shown is just Circuit B reused from Example #3: V pat 12 V, C = 100 µF, and R1 = R2 = R3 = R4 = 25 N. %3D A. The instant after the switch has been re-opened, (t = 0), DRAW THE DISCHARGING CIRCUIT in the space provided, and use it to determine the current flowing through each resistor. Circuit B: The DIS-Charging Circuit: R, R, R, R, ww

Example #5: The RC DIS-Charging Circuit The circuit shown is just Circuit B reused from Example #3: V pat 12 V, C = 100 µF, and R1 = R2 = R3 = R4 = 25 N. %3D A. The instant after the switch has been re-opened, (t = 0), DRAW THE DISCHARGING CIRCUIT in the space provided, and use it to determine the current flowing through each resistor. Circuit B: The DIS-Charging Circuit: R, R, R, R, ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A PMMC type meter has a full scale deflection of 10 mA. The resistance of the coil is 30 ohm. Then (1) shunt value for an Ameter of 50 A range and (2) Find the value of series resistance required for the range up to 500 V.
In the figure given we have u(t)=10· coswt [V]. We assume the diodesand the A-meter (A) to be ideal.a) Plot the waveform of the current flowing through the A-m in scale.b) What is the reading of the A-m, if it is moving-coil type?c) What is the reading of the A-m, if it is moving-iron type?d) Calculate the power factor of the WHOLE structure.
Which change to the circuit will not extend the charging time of one time constant.a. Increasing the value of the capacitorb. Increasing the value of the resistorc. Increasing the voltage from 15 to 20 volts
1. Caused by one or more cells not producing voltage. May be due to cheap construction, overheating or mechanical damage. A. Loss of active materials B. Internal Shorts C. Sulfation D. Internal Corrosion 2. Result of excessive depth of discharge and age. Mostly a problem with cheaper batleries. A. Loss of active materials B. Internal Shorts C. Sulfalion D. Internal Corrosion 3. The unit of measurement used for electrical pressure is- A. ohm B. volt C. energy D. amperes 4. What will happen if a Solar module is not properly oriented? A. Nothing B. Power is reduced due to different solar position during each season C. Power is increased due to different solar position during each season D. All of the above 5. In taking the Voc, you should set the multi-meter : A. High to compensate for the power B. Low to compensate for the current C. Volts DC D. 20 A DC
sketch vL1 and vR2 on a graph. mark the labels in microseconds one time constant after the charging phase begins and the value of each voltage at that time
a) Write the expression for the voltage vC after the switch is closed b) Write the expression for the current iC after the switch is closed. Plot the results of parts (a) and (b).
1- A). Which of the following could be used as a discharge device in an inductive AC circuit? a) resistor b) diode c) metal oxide varistor d) "a" and "c", not "b" B. What is the purpose of a discharge device used in conjunction with opening a highly inductive circuit? a) to minimize the possibility of damage to the circuits insulation as a result of a high induced voltage b) to minimize the possibility of endangering the life of the person opening the controlling switch c) to allow the magnetic field to gradually collapse, thus limiting the value of the self-induced ernf d) all of the above C. The high voltage induced by an inductor when its circuit is opened could be used constructively for a) an automotive ignition system b) an electric fence c) both "a" and "b" d) neither "a" nor "b"
Examine the circuit given below. What is this circuit used for? Write. Exit Simply draw the image taken from the oscilloscope. Calculate separately the times when the led stays on and off. (Note: The charge time of the capacitor C1 can be calculated with 0.693(R1+R2)C1 and the discharge time with 0.692R2C1)
Current is the flow of charges in a directed path. When we connect your mobile phone charger to the sockets in your various homes, charges start flowing through. Describe into details where these charges are generated from.
For the network shown in Figure B22 , assume E = 18V, Diode D¡ as silicon and D2 Germanium, R1=3KQ and R2=2K2. Calculate, i. Current I,, ii. Current In2 ii. Voltage across resistor R2 R1 D E D2 R2 Figure B22 +
Summarize on how testing is carried out on isolators and circuit breakers of high voltage system. High voltage engineering
A PMMC instrument has internal resistance of 0.8 kΩ and gives full scale deflection for 33 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 75 V will be __________________ ohms. a. 226.47 b. -360.00 c. 1472.73 d. 93717.00