Draw the small-signal equivalent model of the following circuit. Using the model, and assuming the transistor parameters of M₁ and M2 to be identical and AM1 = AM2 = 0, a) Find the relation between the transconductance, gm of M₁ and M₂. b) Find the relation between the input voltage v; and Vgs1. c) Find the output voltage, vo. d) Find the small signal voltage gain, Av.

Draw the small-signal equivalent model of the following circuit. Using the model, and assuming the transistor parameters of M₁ and M2 to be identical and AM1 = AM2 = 0, a) Find the relation between the transconductance, gm of M₁ and M₂. b) Find the relation between the input voltage v; and Vgs1. c) Find the output voltage, vo. d) Find the small signal voltage gain, Av.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

As a maintenance engineer in a semiconductor company, you are given a task to replace the current version of dc-biasing circuit for a faulty tester machine. This dc-biasing circuit used an n-channel JFET as shown in Figure 2. Re-design a new dc-biasing circuit using an n-channel D-MOSFET that can produce a similar output current, IDQ as the previous circuit. Your tasks are: (i) Calculate the operating point (IDQ and VGSQ) of the dc-biasing circuit in Figure 2. Then sketch the JFET network transfer curve (ID and VGS). (ii) Without changing the circuit configuration, calculate the values of source resistor, RS and RB to achieve this objective. Determine the commercial value of the new RS and RB.  For cost reduction reason, the values of RD, RA and VDD should be maintained.  The chosen D-MOSFET has a maximum drain current of 8 mA and gate-source cutoff voltage of – 15V.  The new RS value should be 3 times larger than the old RS used in the JFET network to compensate for the high…
circuits by using the small signal models of the transistor. Assume the Early voltage of the transistors are infinitely large. Calculate the small-signal input and output impedances of the following Vcc R1 R1 Rout VB RE Rin R2
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
1. A semiconductor material that has been subjected to the doping process is called -with impurity atoms having and the hole the 2. The p-type material is formed by doping a --- 3. In an n-type material the electron is called the 4. The transistor is a three-layer semiconductor device consisting of either -- of material or 5. The input set for the common-base amplifier relates an input current various levels of output voltage ---- 6. For BJT transistor ICBO =0.02 mA and ICEO= 4------ if B =60 -- ---- to an input voltage -- for (M)
2 a) i) Draw typical output characteristics of a common emitter npn transistor and clearly identify the active, saturation, and cut off regions on your drawing. ii) Explain how you can find the common emitter de current gain, B, and the common emitter ac current gain, hre, from the common emitter output characteristics of an npn transistor. You need to draw typical output characteristics in scales and provide numerical calculations to support your explanation.
Consider the circuit in Figure 2. The transistor has a parameter B that varies between 50 and 200. You want to know the operation of the circuit and the electrical variables at the end points. Calculate the following for B= 50 and B= 200. a) IE, VE and VB (Analysis in DC). b) The input resistance R." (Small signal analysis). c) The voltage gain VO/Vsing (Small signal analy). This 10 ΚΩ www o Rin 100 ΚΩ +3V +1₁ HH 1 ΚΩ 1₁ 1 ΚΩ
The DC Current Gain of a Transistor is Select one: a. Ratio of Collector Current to Base Current b. Ratio of Base Current to Collector Current c. Ratio of Emitter Current to Collector Current d. Ratio of Base Current to Emitter Current
VR2 (t) voltage will be calculated by analyzing the circuit in Figure 2 with a non-linear element using the Small Signal Analysis method. For this purposea) Find the operating point VkQ, IkQ voltage and current values of the nonlinear element.b) Linearize the non-linear element at the operating point.c) Find the voltage VR2 (t) by calculating the effect of the variable source using the linear model.
Q4. For the circuit shown in Figure Q4: i) What is the type of MOSFET and the amplifier configuration? ii) Find the Q-point (Ip and Vps) iii) What is the device transconductance, gm? iv) What are the voltage gain and output voltage? v) Draw the input /output voltage waveforms showing the phase relationship between them. Be sure to label them properly. +20V IDON = 15 mA@ VcsON = 6V VGSTH = 1V 1kQ Rp C2 10M2 Ro1 out Vin 3.3MQ Ra, 47003 Rs 50mV Figure Q4
The circuit in the visual containing a non-linear element will be analyzed with the Small Signal Analysis method and the VR2 (t) voltage will be calculated. For this purpose, find the operating point VkQ, IkQ voltage and current values of the nonlinear element.
In this voltage divider bias circuit, the input is at the base. Output is at the emitter with a high input resistance and low output resistance. The maximum voltage gain is 1 and the coupling capacitors must have a negligible reactance at the frequency of operation. (use to answer a and b) a. Derive the expression for the voltage gain, current gain, and power gain in terms of power delivered to the load, R. b. Sketch both the DC and AC equivalent circuits. c. Derive the expression for ripple factor of Half Wave Rectification with a capacitor filter.
Design-CE255/ purses / Introduction to Electronic Analysis and Design - CE255/E To use it as an amplifier Select one: a. The MOSFET should in the triode region b. The MOSFET should be in the cutoff region c. The MOSFET should be in the saturation region d. The MOSFET could be in saturation or triode region ge Esessment CE255/EE255 (O1) - Dr. Mamoun Al-Mistar Jump to...