Draw a grid 6 in wide by 7 in long with 1-in intersections, and place the given elevations at the intersections in the same arrangement as follows a. Draw the 5-m contours 22 17 28 40 47 52 57 27 24 22 33 41 46 51 35 32 28 27 34 42 49 45 41 37 31 37 43 49 50 52 48 40 36 42 50 45 46 46 42 44 49 52 34 30 38 45 50 55 60 23 34 45 50 55 60 65

Draw a grid 6 in wide by 7 in long with 1-in intersections, and place the given elevations at the intersections in the same arrangement as follows a. Draw the 5-m contours 22 17 28 40 47 52 57 27 24 22 33 41 46 51 35 32 28 27 34 42 49 45 41 37 31 37 43 49 50 52 48 40 36 42 50 45 46 46 42 44 49 52 34 30 38 45 50 55 60 23 34 45 50 55 60 65

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Locate the centroid of the area shown below. 12" Y-axis 4" x = 1.94; y = 4.66 O x =4.66;y=1.94 x =0.00;y = 4.66 O x = 4.66;y=0.00 6" 9" 2" -X-axis
X=192, Y=93
Some questions require you to use the last three digits of your matric card number as input values. For instance : Matric Card No. : A20EA0061 "061" would be your input values where "0" will be labelled as X, "6" as Y and "1" as Z respectively. When entering angles, use the following format : Example#1: 136° 40' 50" type as 136,40,50 Example#2: 34° 05' 09" type as 34,05,09 Q4. Observing angles in both faces will eliminate the effects due to the non-perpendicularity of the trunnion axis, thus eliminating what type of errors in the angle observations? (single word answer and use lower case only). Your answer Figure 1 bearing BA is (350+x)° (40+Y)' (20+z)" bearing BC is (242+x)° (28+Y)' (24+z)" в
Part 2: Beam analysis The timber beam in Figure 2 is simply supported at points A and E. The cross-section of the beam changes from segment AC to CE, as shown below. The Young's modulus of timber may be taken as 12 GPa. The load, geometry and cross-sections of the beam will be instructed to each student in class. B A :B C D E 0.5L 0.5L 0.75L 0.75L bị 0.25hI b2 h2 NA hị Section B-B Section D-D Figure 2 (a) Determine the deflection of the beam at point D by both Virtual Work Method and Castigliano's Theorem. Compare and comment on the differences in these approaches. (b) Calculate the bending and shear stresses at point F on the Section B-B. (c) Develop and sketch the Mohr's circle of stresses corresponding to point F. Show all necessary details, including principal stresses and maximum shear stress.
Channel Area Height Width "a" thickness 200 x 20.25 2610 203 59.4 14.1 7.7 380 x 60 7610 381 89.4 19.8 13.2 Two 380x60 positioned back-to-back with one 200x20.25 on top of them are assembled to form the T-section shown. Determine the location of the centroid of the formed T-section along the y-axis (use the bottom left intersection of the red lines as the point of origin of the axes).
Show me this drawing Step by step how to draw it. thank you 25 105 ø16 30 60° 40 60 70 it's from autocad 20 15
4. Why the lines on the graph do not pass through the origin?
Locate the centroid x̄ of the area.
4. Complete the accompanying set of profile notes and perform the arithmetic check. Provide a sketch of this project's profile view. (You can use excel to sketch) Station BS (ft) HI (ft) IS (ft) FS (ft) BM1 0+00 1+00 2+00 3+00 3+35 4+00 TP1 5+00 5+20 5+30 6+00 BM2 4.58 4.87 2.59 3.79 4.82 4.98 5.05 7.30 4.60 4.78 4.85 4.89 11.21 10.58 Elevation (ft) 427.06
Some questions require you to use the last three digits of your matric card number as input values. For instance : "013" would be your input values where "0" will be labelled as X, "1" as Y and "3" as Z respectively. When entering angles, use the following format : Example#1 : 136° 40' 50" type as 136,40,50 Example#2 : 34° 05' 09" type as 34,05,09 Q6. Calculate the angle "q" in Figure 2. Enter your answer as ddd,mm,ss | C bearing AB is (10+X)° (40+Y)' (30+Z)" В bearing BC is (56+X)° (46+Y)' (00+Z)" A
PROBLEM 4: Determine the centroidal coordinates ( x-bar and y-bar) of the cross-sectional area shown in millimeters. Note: DRAW OR ILLUSTRATE THE SUB-AREAS AND INDICATE THE CENTROID OF EACH SUB-AREA BEFORE ANY NUMERICAL SOLUTIONS.
What type of meridian does the figure represent? W- S Meridian O True Meridian Assumed Meridian Magnetic Meridian Grid Meridian -E