Answered: Determine the torque necessary to…

Determine the torque necessary to rotate an angle 0 at one end of a cylindrical steel bar whose radius is R and length L, the material has a coefficient of resistance to twisting G.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.17P: A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and...

See similar textbooks

Related questions

Q: A 5-lb block is attached to a cable and to a spring as shown. The constant of the spring is k = 8…

Q: A cylindrical rod .5" in diameter is subjected to an axial load of 11,300 lbs. A square bar of .5"…

Q: Problem 1. The beam is loaded by the centered point force P. The supports on both sides are full…

A: Here we will apply equilibrium conditions.

Q: The particle travels along the path defined by the parabola y = 0.5x2, where x and y are in ft. When…

A: The trajectory of particle is At The particle velocity alonmg x axis is

Q: At the instant shown, the arm AB is rotating about the fixed pin A with an angular velocity 42 rad/s…

A: The angular velocity of AB is The angular acceleration of AB is The angular velocity of BD relative…

Q: Water vapor (H2O) is heated during a steady-flow process at 1 atm from 298 to 3000 K at a rate of…

A: To findDetermine the rate of heat supply needed during this process, assuming some dissociates into…

Q: A filtration system is used to separate sand from other matter.14 kg of mixture A and 37 kg of…

A: The objective of the question is to determine the mass of sand in mixture A. We are given that the…

Q: 4. An electrical heater in the form of a horizontal disk of 400-mm diameter is used to heat the…

A: Power required to maintain the heater surface temperature at 70°C is 468 W. Explanation is given…

Q: 3) For the mechanical system shown in Fig. 1, write the force equations at each coordinate and then…

A: The answer is provided below.

Q: Please do question in the image. Also it has to be in vector form since it’s in 3D. Pls show correct…

A: Step 1: Step 2: Step 3: Step 4:

Q: Determine an equivalent lumped mass model for the crankpin.

A: By characterizing the mass of the system as concentrated at discrete places, or "lumps," rather than…

Q: Question 8 A car is submerged in water as shown in the figure below. What will be the resultant…

Q: Isobutane gas and liquid mixture (x=0.9) at stage 1 is running through a valve to get 100% vapor…

Q: Find the axial stress (Subscript[\[Sigma], z]) and axial strain (Subscript[\[Epsilon], z]) for a…

A: Axial Stress (σz): Under plane strain condition, the axial stress is often assumed to be uniform…

Q: Question 4 (Type C): If a clamping force of 350 N is required at A, what is the magnitude of the…

A: F=504.7NExplanation:

Q: Pravinbhai

A: The objective of the question is to determine the mean force in the bolt during operation. This can…

Q: Find , the x-coordinate of the body's centroid. (Figure 1) Express your answer numerically in feet…

A: Given:a=1.45 ftb=3.24 ftc=2.10 ftd=0.5 ftCenter of a hole=(1.13, 0.725)

Q: After greetings, How to solve this problem and what’s the final answer? AND THANK YOU VERY MUCH.

A: The objective of this problem is to find the reactive force at the fixed hinge (left support) of a…

Q: Blocks A and B in (Figure 1) have a mass of 9.0 kg and 12 kg, respectively. Using the coefficients…

Q: TA The nozzle impinges a jet of air at 332 ft/s at a volume flow rate of 92.8 cfm onto the right…

A: Velocity of jet, V = 332 ft/sVolume flow rate, Q= 92.8 cfm=1.5467 ft3/sAssuming the specific weight…

Q: 9) The newly revamped Physicsmobile is going 200.0 kmh when it blows by a Chemwagon going 100.0 kmh.…

A: Physicsmobile:Chemwagon:

Q: 50 MPa 60 MPa 100 MPa α ให้ 70 MPa

A: Given -To Find-

Q: Problem 5.1.6 5.1.6 WP The pump shown in Fig. P5.1.6 produces a steady flow of 10 gal/s through the…

Q: 2. What is one disadvantage of hydroelectric energy? A. It does not work if we don't have coal as a…

A: 2.) C3.) C4.) B5.) B6.) A7.) DExplanation:2.) Hydroelectric energy relies to a big supply of water.…

Q: A fun toy for all ages is the bottle rocket. The one in the picture was made by adding fins to a…

A: Approach to solving the question:Please see attached photos for detailed solutions. Thank you.…

Q: A 1.5 kW motor is running at 1440 rev/min. It is to be connected to a stirrer running at 36 rev/min.…

Q: H.W. For the flow situation shown in Fig. determine the ratio h1/h2 if the area ratio A1/A2=1.8.…

A: To determine the height ratio of the venturimeter from the area ratio as

Q: 3) At the instant show, the velocity of point A of the 1.2 m bar is 3 m/s to the right. Determine…

A: Speed of point BvB=4.37m/sAngular velocity of rod ωrod=3.23rad/sExplanation:Explanation

Q: Determine the tension in each cable and the components of force reaction at D needed to support the…

A: Determine the tension in each cable and the components offorce reaction at D needed to support the…

Q: 15.124 Arm AB has a constant angular velocity of 16 rad/s counterclockwise. At the instant when =…

A: To findDetermine the acceleration of collar D and the midpoint G of bar BD.Givenangular velocity of…

Q: Block A rests on a horizontal tabletop. A light horizontal rope is attached to it and passes over a…

Q: Two 3/8 in thick steel plates are fastened "clamped" together by a 1/2 in -13 UNC bolt as shown in…

A: I have attached the images below Explanation:

Q: For the state of stress shown in figure (a=54 degrees), determine (a) The normal and shear stress…

A: Given on an oblique plane

Q: 1. 10 mol of a simple liquid is heated from 100°C to 500 °C and at the same time are compressed from…

Q: At a given instant the slider block B shown in (Figure 1) is moving to the right with the speed vB =…

A: Ans GivenNow draw the FBD of the given slider B asNow calculate the length d asNow from…

Q: The box wrench is subjected to the P = 38 lb force. (Figure 1) Determine the principal stresses at…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Question 2 (35 marks): A company has a project to complete. To complete the project, the following…

A: To draw the Project Diagram/Network (15 pts) and develop a Linear Program (20 pts) for computing the…

Q: A child of mass m = 40 kg is initially placed on the edge of a uniform disk, of mass M = 100 kg and…

A: The objective of the question:Determine the initial angular speed. Given data:The mass of the child…

Q: The composite bar consists of a 20-mm-diameter A-36 steel segment AB and 50-mm-diameter red brass…

A: The diameter of AB segment (steel) is The diameter of DA and CB segment (brass) is

Q: Water, initially a saturated liquid at 500 kPa, undergoes two reversible processes: 12: isobaric…

Q: The smooth particle has a mass of 80g It is attached to an elastic cord extending from O to P and…

A: The answer is provided below.

Q: The right side leg of the pictured manometer is open to the atmosphere with a pressure of 1 atm. The…

A: The pressure in the left hand lag is 106.9kPaExplanation:Explanation

Q: Use BS 4500A:1970 to determine the dimensional tolerance on the critical diameters in Gear Sub-…

A: BS 4500A:1970 provides guidance on limits and fits for engineering applications, including…

Q: Find the friction for water at 60°C flowing at 0.0057 m³/s in a 4 in Sch 40 steel pipe.Answer to 3…

A: <math style="font-family:'Times New Roman'"

Q: Find a general equation for the navier stokes equation for any initial value and provide an example…

A: Concept Used:The concept behind the above question involves understanding the Navier-Stokes…

Q: First find the friction factor then Apply the formula.

Q: 18.107 Determine the moment of inertia of the object described in Problem 18.106 about the axis…

Q: What is the force member in LC1 in N?

A: The length are The mass applied at B is

Q: 6-20. Determine the force in each member of the truss and state if the members are in tension or…

A: Determine the force in each member of the truss and state if the members are in tension or…

Q: 1 ) Derive a free body diagram with spring-mass-damper elements for given system. QUESTION 2 )…

A: Given:System diagram is providedTo find/derive:Free body diagram with spring-mass-damper elements…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Determine the torque necessary to rotate an angle 0 at one end of a cylindrical steel bar whose
radius is R and length L, the material has a coefficient of resistance to twisting G.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Derive torsion equation.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The shaft of a motor has a length of 15 times its diameter and has a maximum twist of 1.5degrees when twisted at 2.5 KN-m torque. If the modulus of rigidity of the shaft is 83 Gpa,find the shaft diameter in m
A shaft is fixed at support C and has a torque of 75lb.ft with respect to free end at a distance of 0.75ft from C. It remains constant for 0.75ft before a negative uniformly distributed torque of 1200lb.ft/ft at a distance of 1.5ft is introduced. The shaft then remains flat for 1.5ft to free end with a torque of 600lb.ft. where in the shaft is the torque equals to negative 1200lb.ft measured from the free end?
A torsional bar is subjected to two external torques (10Nm and 5Nm) and a distributed torque(15Nm/m) at the locations indicated in the picture. The angle of twist at A (z = 0) is 0. Theshear modulus is 2GPa., if the bar has both A and C fixed (i.e., the torque applied at C is replaced by a fixed support), find the angle of twist at B.
Two circular shafts, one hollow and one solid, are made of the same material and have the diameter shown below.If TH is the twisting moment that the solid shaft can resist, what is the ratio of Th to Ts
A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and torque applied at both ends is 340 N.m. Determine the angle of rotation in radians.
A steel cable is supporting a load of F = 9800 lb and is wrapped around a drum attached to gear A as shown. Assuming the motor is locked in place while the load is applied, answer the following. (1) What is the internal torque in the flexible shaft? (2) What is the rotation of gear A in degrees? 7.0 in bearing gear A 42.0 in gear B bearing 8.0 in -motor solid circular shaft r = 1.2 in G = 2000 ksi L = 38 in
A torsional bar is subjected to two external torques (10NM and 5Nm) and a distributed torque (15NM/m) at the locations indicated in the picture. The angle of twist at A (z = 0) is 0. The shcar modulus is 2GP.. Compute the following quantitics: (a) the reaction moment at A, (b) the angle of twist at B, and (c) the angle of twist at C. OD=5cm OD=4cm 15Nm/m 10Nm 5 Nm A 15 cm 10cm 8 cm 15 cm F A 8cm B C
The hollow rod shown below is 2.99 meters long and is subjected to a torque of 988 Nm at end B. The diameter of the rod is 30 mm and has a wall thickness of 5 mm. The shear modulus of the material is 80 GPa, calculate the angle of twist in radians at B. TNm B meters
A solid constant-diameter circular shaft is subjected to the torques of TA = 480 lb-ft, TB = 1060 lb-ft, Tc= 860 lb-ft, and Tp = 280 lb-ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in %D Section 6.6. (b) If the allowable shear stress in the shaft is 5800 psi, what is the minimum acceptable diameter for the shaft? TB TA Tc (1) Tp (3) В C D Answer: (a) T1 = Ib-ft T2 = Ib-ft T3 = Ib-ft (b) d = in.
0.6- 0.3 1.0 4.2 320 lb 1:25- 5.25 340 lb 2 1.0 1.95 0.3 B 0.6
A 45 mm diameter shaft is made of steel with a yield strength of 400 MPa. A parallel key of size 14 mm wide and 9 mm thick made of steel with a yield of 340 MPa is to be used. Find the required length of key, if the shaft is loaded to transmit the maximum permissible torque. Use maximum shear stress theory and assume a factor of safety of 2.
Determine the resisting torque at support A and B , of the shaft shown in the figure.