Determine the stability of the wall in different conditions mentioned down in table and provide a spreadsheet utility program to obtain factor of safety against bearing capacity failure, Ho a (°) B (*) pa (kN/m³) Ø () 8 (*) (m) 5.0 5.5 6.0 6.5 20 100 1600 36 24 20 20 20 100 100 100 1600 1650 1650 36 38 38 26 28 30

Determine the stability of the wall in different conditions mentioned down in table and provide a spreadsheet utility program to obtain factor of safety against bearing capacity failure, Ho a (°) B () pa (kN/m³) Ø () 8 () (m) 5.0 5.5 6.0 6.5 20 100 1600 36 24 20 20 20 100 100 100 1600 1650 1650 36 38 38 26 28 30

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.11P

See similar textbooks

Similar questions

arjumo Но |ha PA r Figure 1 calculais
A piece of engineering equipment is supported by thefoundation shown. The diameter of the circular pinis 20 mm. a.) Determine the value of P so as not toexceed the allowable bearing stress of310.5 Mpa in the circular pin.b.) Determine the value of P so as not toexceed the allowable shearing stress of 138Mpa in the circular pin.
7. 4) Determine the increase in vertical stress at a depth (2) m belowpoint A due to surface loads shown in Figure (2). m or n L.O 10.0 9.0 8.0 7.0 6.0 5.0 4.0 E 3.0 2.5 2.0 G.S.L xxxx 1.5 z 1.5 -0.006- -0.007 0.006 0.009 0.15 19 -0.011 0.010 Section b-b 2 160 kPa 0.2 0.012 0.014 m or n 2.5 3 G014 0.016 0.020 & 0.25 0.3 0,024 120 kPa 4 2.000 0.4 5 -0.04 6 0.06 S b + 7 8 9 10 0.13 ats 0.34 0.5 0.6 0.7 0.8 0.9 1.0 m or n (a) 2.5 m 160 kPa 120 kPa ais. 1.5 . 1.5 2 2.5 3 2.5 T 3 1.5 m 2 m 0.5 m 4 4 5 Fig.(2) 6 7 8 9 . 1 10 11.0 0.9 0.8 0.7 0.6 40.5 10.4 0.3 0.25 0.2 m of n E 0.15 0.10 .9 10
Find active thurst P₁ = ? when tension crack has not yet appeared A B 2 m 3 m C 2 Clay Y₁ = 17 kN/m² 2 c=15 kN/m² $₁ = 20° 3 1₂= 16 kN/m c = 0 (Sand) $₂ = 20°
Situation 3: 200.02 kN 75.05 mm 50.05 mm 15.05 deg 200.02 kN 1. Tensile stress at section A-A 2. Shear stress at section A-A 3. What angle of plane A-A gives maximum shear stress?
6. A rectangular 12m x 9m coal pillar is located 100m below surface. Panel road widths are 7m, mining height is 2.5m. Panel encounters a dolerite sill and the load increases by 15%. i. Calculate the load and safety of the pillar. ii. Calculate the thickness of the dolerite sill and new safety factor. iii. Discuss the controllable parameter/s in regards to enhancing the stability of the beam in the roof.
What is the shearing stress developed at the neutral axis of the beam with a circular cross section having a diameter of 19 mm and a shear force V = 29 kN. Assume that the shearing stress is uniformly distributed across the neutral axis. Answer must be in MPa. Next» • Previous
A piece of engineering equipment is supported by thefoundation shown. The diameter of the circular pin is 20 mm. a.) Determine the value of P so as not to exceed the allowable bearing stress of 310.5 Mpa in the circular pin.b.) Determine the value of P so as not to exceed the allowable shearing stress of 138 Mpa in the circular pin.
What is the value of the shear stress at the neutral axis in a rectangular section of base b, height h and subjected to the shear force F? 1.3F/b O 2. (3F)/(2bh) O 3. F/2
b 420mm b 850 mm b = 039 mm M = 6.5 KN.m E = 186 KN.m 1. Calculate the max. tensile and compressive strength 2. Radius of curvature
Stresses in Soil Mass: Mohr's Circle 131.6 kPa 53.6 kPa 315.2 kPa 315.2 kPa 35 131.6 kPa 2. Find Normal and Shear Stress at Failure Plan A-B. Enter your answer to three significant figures. (1 decimal place)
[?] ?? = [150 −60−60 −180]➢ Determine and graph using Mohr's circle the principal stresses and theaddresses associated with these.➢ Determine and graph the maximum shear stresses.➢ Plot the possible failure planes.➢ Finally, what is the value of the maximum tangential stress and at whatorientations take place?