Define step by step please Determine the correctness or otherwise Assertion(A) and the Reason (R).Assertion (A) : In a power plant working on aRankine cycle, the regenerative feed water heatingimproves the efficiency of the steam turbine.Reason (R): The regenerative feed water heatingraises the average temperature of heat additionin the Rankine cycle.orrect

Given; Assertion A: In a power plant working on a Rankine cycle, the regenerative feed water…

Answered: Determine the correctness

Engineering

Mechanical Engineering

Determine the correctness

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the schematic or plant layout. Draw the T-s diagram Mandatory: A, B, C Suggested: D, E A reheat cycle has the following data: Throttle, 8.5 MPa at 400°C Turbine exhaust, 0.06 MPa For an ideal cycle, determine the: (A) Work (B) Thermal efficiency (C) Heat rate (D) What is the thermal efficiency of the corresponding Rankine cycle? (E) What is the percent improvement in engine heat rate of the reheat cycle from the Rankine cycle.
Problem (1.2) A steam power plant working according to simple Rankine cycle. It has a high pressure of 3 MPa and it maintains 60°C in the condenser. A condensing turbine is used, but the quality should not be lower than 90% at any state in the turbine. Find the cycle efficiency. [reference: Fundamentals of Thermodynamics by Borgnakke & Sonntag prob.11.18,p-460].(Ans.33.2 %).
High-P turbine Low-P turbine Reheater Boiler P=Ps=Paeheat Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 Click Save and Submit to save and submit. Click Save All Answers to save all answers. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m³/kg Calculate the specific heat input of the system in kJ/kg to 3 decimal places. 7L
1. Consider the following schematic of a power plant (operating in what is called a 'Rankine Cycle') Turbine Steam generator Condenser Coling water Economiaer The power plant control room reports that the plant is operating continuously at the following peak load conditions: a. Power to pump = 300KW b. Rate of steam flow = 25 kg/s c. Cooling water temperature at condenser inlet = 13 C d. Cooling water temperature at condenser outlet = 34 C Additionally, the following measurements were made at various points in the piping connecting the power plant components Data Pressure Temp. Quality enthalpy Specific Velocity (kJ/kg) point (kPa) volume (m/s) (m3/kg) (C) (x) 1 6200 2 6100 43 5900 177 ---- 4. 5700 493 ----- 5 5500 482 ----- 6 103 0.94 183 7 96 43 -----
1. A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and a 37.50308414 atm reheat pressure, the throttle and reheat temperature of the steam is 1302 R, condenser pressure is 4.3 kPa. Determine the difference between the simple Rankine cycle efficiency and the reheat Rankine cycle efficiency, in percent.
Question 4 a) A power plant based on the ideal Rankine cycle has a net power output of 10 MW.Superheated steam enters the turbine at 10 MPa, 500 (Degree)C. The condenser pressure is 15 kPa.Determine:i) the mass flow rate of the steam.ii) the rate of heat input to the cycle.iii) the thermal efficiency.
b M b Vo) LTE 1 MJ 31% 14:09 High-P Low-P turbine turbine Reheater Boiler P4 = P3 = Prchet Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 Click Save and Submit to save and submit. Click Save All Answers to save all answers. 3-4: Inlet steam at 17.5 MPa and 600 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m3/kg Find the specific enthalpy in kJ/kg at state 4.
A power plant using a Rankine power generation cycle and steam operates at a temperature of 81.25°C in the condenser, a pressure of 5 MPa in the boiler and a maximum boiler temp of 775°C. The cycle operates at steady state with a mass flow rate of 2.5kg/s. Use the steam tables in the appendix of Sandler (p. 917 to 925). a.) Draw out the cycle, calculate the work required for the pump, the work output by the turbine, the heat into the boiler, and the heat out of the condenser. b.) What is the efficiency of this power plant? c.) If the turbine was only 89% efficient but still adiabatic (only generates 89% of the calculated work from part b), what is the overall efficiency of the cycle?
Question 4 a) A power plant based on the ideal Rankine cycle has a net power output of 10 MW.Superheated steam enters the turbine at 10 MPa, 500 C. The condenser pressure is 15 kPa.Determine:i) the mass flow rate of the steam.ii) the rate of heat input to the cycle.iii) the thermal efficiency.
My Question: In the steam power plant of problem #1, the reheater developed a leak and it was decided to run the plant bypassing the reheater at 1 bar. Determine the thermal efficiency and boiler capacity to develop the same power output.Problem#1. In a Reheat Cycle steam enters the turbine @ 40 bar and 400 C. It expands isentropic ally to 6 bar and is reheated at constant pressure to 400 C. This steam expanded isentropic ally to 1bar and is reheated at constant pressure to 200 C. Finally this steam is expanded isentropic ally in the condenser pressure of 0.1 bar. Determine the thermal efficiency and the capacity of the boiler if 10,000 KW of power output is required.
Gas Turbine HW.pdf Gas Turbine Home Work (1) A simple ideal Brayton cycle with air as the working fluid has a pressure ratio of 10. The air enters the compressor at 520 R and the turbine at 2000 R. Assuming the variation of specific heats with temperature is constant at room temperature., determine (a) the air temperature at the compressor exit, (b) the back work ratio, and (c) the thermal efficiency. Home Work (2) A simple Brayton cycle using air as the working fluid has a pressure ratio of 8. The minimum and maximum temperatures in the cycle are 310 and 1160 K. Assuming an isentropic efficiency of 75 percent for the compressor and 82 percent for the turbine, determine (a) the air temperature at the turbine exit, (b) the net work output, and (c) the thermal efficiency. •..
High-P turbine Low-P turbine Reheater O Boiler P=Ps = Pahet Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 2 A. l Click Save and Submit to save and submit. Click Save All Answers to save all answers. 3-4: Inlet steam at 17.5 MPa and 600 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m3/kg Find the specific entropy in kJ/kg at state 1 to 3 decimal places. טך