Determine magnitude of the stresses acting on plane inclined at an angle 0 = 30°, where the vertical stress o, is 90 MPa and the horizontal stress o is 20 MPa. Draw a schematic diagram of Mohr's circle and label all components of the graph.

Determine magnitude of the stresses acting on plane inclined at an angle 0 = 30°, where the vertical stress o, is 90 MPa and the horizontal stress o is 20 MPa. Draw a schematic diagram of Mohr's circle and label all components of the graph.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.25P: -18 through 7.4-25 An clement in plane stress is subjected to stresses sx,,sy., andtxy(see figure)....

See similar textbooks

Related questions

Q: 6o vam 14 A GJVENI G =386 MDa T25KN-m `M=13KN-M D r-풍(물)+, J= 폭(을 Q1. DRAW STRESS STATES AT A IN X-Y…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: Question 3) Plane stress state at a point is given in the figure. a) Calculate the principal…

A: τxy=10 Mpaσ1,2=σx+σy2±σx-σy22+τxy2 As it is case of pure shear so σx=0 and σy=0…

Q: Three loads are applied to the short rectangular post shown. The cross-sectional dimensions of the…

A: GivenFy=160kN=160×103 NFx=-100 kN=-100×103 NFz=-70 kN=-70×103NNow from above diagram we…

Q: 4 ksi The state of plane stress at a point is shown on the element. (a) Draw Mohr's circle neatly to…

Q: 90 MPA 60 MPA 20 MPA

A: Given that, σx=-20 MPa,σy=90 MPa,τxy=60 MPa, Steps to draw mohr's circle: 1. Take direct stress at…

Q: Using Mohr's circle, determine: (a) The stresses acting on an element oriented at an angle 0=-30°…

A: Mohr's circle shows the transformation equations of the issues of planar stress. It is helpful to…

Q: QU For the state of plane stress shown below, construct a Mohr's circle and determine (a) the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and…

A: Given:- σx=70 MN/m2σy=50 MN/m2τxy=30MN/m2θ=30° To find:- The magnitude of the normal, tangential,…

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

Q: A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the…

A: Now we have the moment equation asMx=16×510-11×230=5630kN.mm=5.63kN.mMy=-20×510=-10200 kN.mm=-10.2…

Q: The stress at a certain point is as shown in the figure. If the maximum in-plane shear stress…

Q: 5. The normal and shear stresses acting on one plane passing through a point in a soil mass are 120…

Q: Using Mohr's circle, determine: (a) The stresses acting on an element oriented at an angle 0-30°…

A: Mohr circle is a two dimensional graphical method of expressing the normal stresses and shear stress…

Q: A same circular plate with radius of Ro-560mm and thickness of h=7.42mm is considered here again.…

Q: determine (a) the principal stresses at K, (b) the maximum in-plane shear stress and average normal…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

Q: The stresses shown in the figure act at a point in a stressed body. If o = 239 MPa in the direction…

Q: At a point in a component, the state of stress is shown on the element below. Assume that the stress…

Q: Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the…

Q: For the state of plane stress shown in Fig. determine (a) the princi-pal planes, (b) the principal…

A: σx=50MPaσY=-10 MPaτxy=40 MPa (a) the principal planes…

Q: - The state of plane stress is represented by the stress element below. Draw the Mohr's circle,…

Q: When there is a plane stress condition as shown in the figure, display this stress in the form of…

Q: The stresses shown act at a point in a stressed body. Assume stress magnitudes of Sx = 13,300 psi,…

Q: Determine (a) the principal stresses and (b) the maximum shear stress and associated normal stress…

A: normal stress in x direction σx=300 MPanormal stress in y direction σy=-100 MPa (-ve for…

Q: Determine the equivalent state of stress if an element is oriented 20° clockwise from the element…

Q: Problem 2. Amaterial element in plane stress is subjected to stresses: = -5000 psi Ox Oy = -2000 psi…

Q: QI/ For the state of plane stress shown below, construct a Mohr's circle and determine (a) the…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: For the element shown below, determine: 1- The principal stresses and the maximum in-plane shear…

A: A perpendicular force applied on a body per unit area is referred to as stress. There are three…

Q: For the state of stress shown in the figure, determine the stress component Txy so that the maximum…

Q: Determine the equivalent state of stress on an element at the same point oriented 60°…

A: Given Data: The value of σx=150 MPa The value of σy=100 MPa The value of τxy=75 MPa The orientation…

Q: Draw the Mohr's Circle of the stress element shown in figure. Find:- 14MPA 24 10 20 MPa The stresses…

A: Given Normal stress at X axis = 20 MPa Normal stress at Y axis = 14 MPa Slope of plane = 24 and 10…

Q: The normal and shear stresses acting on one plane passing through a point in a soil mass are 120 psi…

A: Among the applied normal stresses on mutually perpendicular planes the stress corresponding to…

Q: For the state of plane stress, stress components are shown on the element in Figure Question 1: a)…

Q: 3. Listed below is a combination of stresses acting at a point and referred to axes x and y in an…

Q: 50 MPа B 80 MРа 80 MPа A 25 MPа 50 MPа

Q: The hollow cylinder is fixed at the wall and pressurized at p = 2,000 Pa. Its outer diameter (OD)…

Q: Try

A: Given Data : σx=60 MPa σy = 0 τxy = 40 MPa.

Q: 2.7. The principal stresses at a given point are o1 =10 MPa, ơ2=-100 MPa. Sketch Mohr's circle for…

A: Given data: The positive principal stress, σ1=10 MPa. The negative principal stress, σ2=-100 MPa.…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: We can answer the first part because it is already has 3 unknowns so we will answer the part (a).…

Q: Given sigma x=100 MPa, tau xy=50 MPa, determine stresses at an angle 30 degrees CW from x-axis.

Q: * 'Determine the ox 30 MPa 10 MPa 20 MPa The state of plane stress at a point is represented on the…

A: find the segma x in oriented element.

Question

i need the answer quickly

Determine magnitude of the stresses acting on plane inclined at an angle 0= 30°,
where the vertical stress o, is 90 MPa and the horizontal stress o, is 20 MPa.
Draw a schematic diagram of Mohr's circle and label all components of the graph.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-18 through 7.4-25 An clement in plane stress is subjected to stresses sx,,sy., andtxy(see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the element is also shown as the line nt. The normal stress on the plane that is rotated from the x face is: I grid square = 5 MPa
The stresses acting on element A in the web of a train rail are found to be 'X (MPa)' tension in the horizontal x-direction and 'Y (MPa)' compression in the vertical y-direction. Also, shear stresses of magnitude 'S (MPa)' act in the directions shown in the figure. Draw Mohr's circle for the state of stress. Determine the stresses (Ox', Oy' and Txy') acting on an element oriented at an angle 'D' from the horizontal Show these stresses on a sketch of an element oriented at this angle X=45MPA,Y=150MPA,S=52MPA,D=-40 Degree
Determine magnitude of the stresses acting on plane inclined at an angle 0 = 30°, where the vertical stress o, is 90 MPa and the horizontal stress ox is 20 MPa. Draw a schematic diagram of Mohr's circle and label all components of the graph.
For the state of plane stress shown in Figure-1. below; now. Draw Mohr's circle, and also Determine the maximum in-plane shear stress,
The state of stress at a point in a machine component is given by ox = 120 MPa, oy = 55 MPa, Oz = -85 MPa, Oxy = -55 MPa, Oxz = -75 MPa, and oyz = 33 MPa. Construct the Mohr's circles of stress for this stress state and find the maximum shear stress.
Consider the general case of plane stress as shown. Write a computer program that will show a plot of the three Mohr’s circles for the element, and will also determine the maximum in-plane shear stress and the absolute maximumshear stress.
Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the element is also shown as the line nt. The shear stress on the plane that is rotated from the x face is: 1 rid square =5 MPa
A plane element is subjected to stress as shown in below figure. Determine the radius of the mohr circle drawn for this state of stress. 40 MPa 40 MPa 60 MPa
The main stress, the maximum shear stress, and the dead angle are obtained when the stress is given as shown in the picture below.Draw Mohr's circle.
Problem 2: A state of plane stress at a point on the surface of a structure consists of the following stress components: Ox = 18 ksi, oy = 24 ksi, and Txy = 15 ksi. Note that the stress components act in the directions shown on the element below. Ox Txy 24 ksi бу 18 ksi 15 ksi (a) Draw a complete Mohr's circle for this stress state. Clearly label the X and Y faces, the center C, and the radius R. (b) Using Mohr's circle, determine the stress components Ox, Oy, and Txy on an element rotated 25° counter-clockwise from the original element shown. Label all of these quantities on the circle. (c) Show all stresses from part (b) on a properly oriented stress element. Be sure to include all stress components acting on the element.
The state of plane stress at a point is represented on the element shown in the figure. The element oriented 40° 'counterclockwise. Find the value of ox 30 MPa 20 MPa -10 MPa +55.2 Mpa +11.4 Mpa -37.9 Mpa +24.7 Mpa -11.4 Mpa +37.9 Mpa -55.2 Mpa -24.7 Mpa +45.9 Mpa -45.9 Mpa