DETAILSThe I vs t graph shown below is for an LR circuit without a battery.I (A)3.Determine the time constant of the LR circuit.2.If R= 60, determine L.1.t (s)102. DETAILSThe Q vs t graph shown below is for the capacitor of an RC circuit.Q (C)8.6.Determine the time constant of the RC circuit.4.If R = 30, determine C.2.t(s)3.

Answered: Image /qna-images/answer/2f83f9b2-a567-480e-ac9b-3923fc134017.jpg

Answered: DETAILS The I vs t graph shown below is…

DETAILS The I vs t graph shown below is for an LR circuit without a battery. I (A) 3. Determine the time constant of the LR circuit. 2. IfR60, determine L. 1. t(s) 10

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter21: Circuits And Dc Instruments

Section: Chapter Questions

Problem 77PE: Unreasonable Results (a) Calculate the capacitance needed to get an RC time constant of 1,00x103 s...

See similar textbooks

Similar questions

Consider a series RC circuit as in Figure P18.35 for which R = 1.00 M, C = 5.00 F, and = 30.0 V. Find (a) the time constant of the circuit and (b) the maximum charge on the capacitor after the switch is thrown closed. (c) Find the current in the resistor 10.0 s after the switch is closed. Figure P18.35 Problem 35 and 38.
A 500- resistor, an uncharged 1.50-F capacitor and a 6.16-V emf are connected in series, (a) What is the initial current? (b) What is the RC time constant? (c) What is the current after one time constant? (d) What is the voltage on the capacitor after one time constant?
A person with body resistance between his hands of 1.00 k accidentally grasps the terminals of a 20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation. (b) If the internal resistance of the power supply is 2000 , what is the current through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low-re si stance devices? Explain your reasoning,
An uncharged series RC circuit is to be connected across a battery. For each of the following changes, determine whether the time for the capacitor to reach 90% of its final charge would increase, decrease, or remain unchanged. Indicate your answers with I, D, or U, respectively. (a) The RC time constant is doubled. (b) The battery voltage is doubled. (c) A second resistor is added in series with the original resistor.
Unreasonable Results (a) Calculate the capacitance needed to get an RC time constant of 1,00x103 s with a 0.100- resistor, (b) What is unreasonable about this result? (c) Which assumptions are responsible?
b. About how many time constants does it take to charge a capacitor in an RC circuit to 50% of its maximum value?
2. A simplified model of an axon based on a simple RC circuit is shown below. Consider an incremental length of 5 x 10-10 m non-myelinated segment of an axon whose properties are listed in the table below. A potential of 80 mV is maintained at point a. a. How many discrete segments make up a distance of 0.01 mm? b. What is the voltage at a point 0.01 mm away from a? a | R. Rm RT R Values Property Axon Radius 5 x 10m
The resistance in an RC circuit is comprised of a 1.5-MQ resistor in parallel with a 2.0-MQ resistor. What is the time constant for this circuit if the capacitance is 2.5 µF? Select one: a.5.0 μs b.4000 s c.2.0 s d.7.0 ms e. 120 s
The Q vs t graph shown below is for the capacitor of an RC circuit. Q (C) 10 7.5 5. 2.5 7 14 21 28 35 42 49 56 63 70 t(s) Determine the time constant of the RC circuit. TH If R= 802, determine C. C= MY NOTES
Suppose you have a RC circuit with emf of the power supply equal to 18 V and the time constant equal to 0.2 s, then the potential difference (in V) across the capacitor at t = 0.15 s is: O a. 6.7 O b. 9.5 O c. 12.6 O d. 10 O e. 8.5
Compute for the total energy of the entire circuit. Select one: a. 128.42 micro Joules b. 352.12 micro Joules c. 273.56 micro Joules d. 478.08 micro Joules
M 1 Ω 11 V 3 W Ω 16 V a. Write Kirchhoff's junction rule for all junctions in the circuit. b. Write Kirchhoff's loop rule for all the loops in the circuit. c. Solve the circuit by finding the values of all the currents. 2 Ω mi M In this assignment you will be following the problem solving strategy for Kirchhoff Rules. 1. Reproduce, as neatly as possible, on paper, the circuit shown above. Do not make the circuit too small as you will have to add things to it later. 2. Label all relevant points in this circuit. For your benefit these points are marked with dots in the Figure above and they include: circuits junctions (i.e. places where 3/more wires connect), wire "corners" (i.e. places where a single wire is bent), and locations between two components on a single straight wire. These will help identify loops as well as making it easier to keep track of potential differences. Use lower case letters (a, b, c, ...) for this task. 3. For each junction draw and label the currents coming in…