Design an inclined belt-roller conveyor system for a production plant as shown in Figure 1. Therequired angle of inclination is a = 10°. The AC induction motor with 4-poles that drives the pulleyand belt has to be selected based on the requirements listed in Table 1 and the motor catalogueprovided in Brighten portal (Topic 8). Select a suitable motor for your design and justify yourdecision. The product transfer speed required is minimum 0.05 m/sec and maximum 0.45 m/sec.Assume suitable safety factor to provide sufficient warranty for the system.Table 1: Required Specification and Structural SpecificationTotal mass of table and work, m₁ = 20 kg Mass of pulley 2 = 450 gramsDrum diameter, Da = 110mmBelt roller efficiency, r = 0.85Mass of the roller, m2 = 1.5kgBelt-pulley efficiency, ¹p = 0.85Pulley 1 diameter, D₁ = 50mmFriction coefficient of sliding, μ = 0.04Pulley 2 diameter, D₂ = 110mmAvailable power supply: 19, 220 V, 50HzMass of pulley 1 = 250 gramsOperation: Continuous duty.Belt ConveyorLoadLinear GuideBeltDrive PulleySecondary PulleyFigure 1: Conveyor Belt SystemPrimary PulleyMotor

Given,Mass of the work table setup and weight of pay load = 20 kgThe pull force required at drum to…

Design an inclined belt-roller conveyor system for a production plant as shown in Figure 1. The required angle of inclination is a = 10°. The AC induction motor with 4-poles that drives the pulley and belt has to be selected based on the requirements listed in Table 1 and the motor catalogue provided in Brighten portal (Topic 8). Select a suitable motor for your design and justify your decision. The product transfer speed required is minimum 0.05 m/sec and maximum 0.45 m/sec. Assume suitable safety factor to provide sufficient warranty for the system.

Design an inclined belt-roller conveyor system for a production plant as shown in Figure 1. The required angle of inclination is a = 10°. The AC induction motor with 4-poles that drives the pulley and belt has to be selected based on the requirements listed in Table 1 and the motor catalogue provided in Brighten portal (Topic 8). Select a suitable motor for your design and justify your decision. The product transfer speed required is minimum 0.05 m/sec and maximum 0.45 m/sec. Assume suitable safety factor to provide sufficient warranty for the system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following data are available for a belt conveyor design: 1. Conveyor capacity: = 1300 t/h; 2. Belt speed = 1.5 m/sec; 3. Conveyor height = 15 m; 4. Conveyor length = 175 m; 5. Mass of a set of idlers = 15 kg; 6. Idler spacing = 1.2 m; 7. Load due to belt = 25 kg/m; 8. Inclination angle of the conveyor = 10 deg.; 9. Coefficient of friction = 0.05; 10. Start-up factor = 1.5; 11. Drive efficiency = 0.90; 12. Friction factor = 12; and 13. Breaking strength loss factor = 0.80 Determine the following: (1) Belt tension, (2) Load due to idlers, (3) Minimum motor power; (4) Acceleration of the conveyor belt, and the (5) Belt breaking strength.
With a driveshaft turning at 2000 rpm , I then have a spring that can rotate a shaft 5000 rpm, I want this spring to assist in the drive of the driveshaft, how can I express that or calculate the effect of adding the spring would make. Including a spring system alongside a driveshaft that can assist the drive up to 5000rpm, how can I integrate the spring system to assist in the driveshaft drive, calculations on the change in rotation the spring would have of the driveshaft speed
B: A motor drives a hoist which raises a load of 1000 kg with a velocity of 1 m/sec, calculate the input power of the motor assuming the hoist gearing efficiency to be 0.8, motor efficiency to be 0.75.
Task 4 Select a suitable three-phase 400v 50hz motor for a 15O0kg hoist being driven by 0.5m diameter 20 rpm drum and a 1:75 gearbox with 20% friction. The accelerating torque is 12Nm. a) Give details of the steady hoisting torque, motor speed, and kw rating. b) Also recommend a suitable motor type and control gear including starter
Which type of clutch/brake is depicted in the figure below? 10⁰ O A. Internal expanding rim clutch/brake O B. External contracting rim clutch/brake OC. Band-type clutch/brake O D. Axial clutch/brake OE. None of the above
Define an Articulated Robot? How many joints does a 6-axis Articulated Robot have? How many joints does a Scara 4-axis robot have? # An articulated robot is a robot with rotary joints (e.g. a legged robot or an industrial robot). Articulated robots can range from simple two-jointed
Design the electro -hydraulic circuit for the lifting and shifting operation as shown in Figure 2 with the following requirements. Following are the sequence of operation. Products are required to be transferred from lower level conveyor to higher level conveyor using two hydraulic Cylinders (Cylinder A and Cylinder B) and a conveyor belt (semi rotary motor) Cylinder A lifts the product on receiving it at lower level to the platform. Then, Cylinder B shifts the product from the platform to the conveyor, Then the conveyor motor should be rotated after 5 seconds to transfer the product to packaging Repeat the sequence of operation for 10 trials. NOTE: use independent DCV for each actuators (Cylinder A, Cylinder B and Conveyor motor)
A V-belt drive is required from a 10kW, motor to drive an output pulley of 240mm diameter at 500pm with a reduction of 4:1. It is a light-duty machine that runs 6 hours each day. Using data given in the table and chart below, what would be a suitable V-belt and motor pulley diameter for a single belt installation?
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
What are the different design parameters for a conveyor? atleast 10 example
Please give me answer in 45 min. Calculate the minimum technical specifications of a linear pneumatic cylinder that meets the requirements of raising the transfer mechanism in 3 seconds and lowering in 2 seconds.Specifically, the distance to travel (stroke) and diameters.
Products are required to be transferred from lower level conveyor to higher level conveyor using two hydraulic Cylinders (Cylinder A and Cylinder B) and a conveyor belt (semi rotary motor) Cylinder B lifts the product on receiving it at lower level to the platform. Then, Cylinder A shifts the product from the platform to the conveyor, Then the conveyor motor should be rotated after 5 seconds to transfer the product to packaging Repeat the sequence of operation for 10 trials. NOTE: use independent DCV for each actuators (Cylinder A, Cylinder B and Conveyor motor) Required: Components required Hydraulic circuit – provide proper labelling Electrical circuit– provide proper labelling Provide the state diagram :- displacement step and displacement time diagram –