Describe the operation of different types of lubrication methods used in a petrol engine (80 - 100 Words) a. Boundary lubrication b. Hydrodynamic lubrication c. Force Feed lubrication d. Mist Feed (Boundary)

Q: A Dual Combustion Cycle uses a compression ratio of 12/1. The cut off ratio is 2/1. The temperature…

A: The compression ratio,(r)=12 The cut-off ratio, (ρ)=2 The inlet temperature,(T1)=280 K The inlet…

Q: Q1/ A beam AB of span 8 meters is simply supported at the ends, as shown in Fig. 1. It carries a…

A:

Q: Please answer the last two questions

A: If steel is too hot, it can be cooled using quenching or water-cooling methods. If it is too cold,…

Q: An automobile having a mass of m= 1650kg is subjected to vibration in the vertical direction while…

A: Given Data: Automobile mass m=1650 kg road have Sinusoidal amplitude Y=0.07 m wavelength λ=6.5 m…

Q: Q1 A material was tested under the proportionally increasing state of stress 201= - 202 = - 03.…

A: Given Data: (a) 2σ1=-2σ2=-σ3σ1=200 MPa(b) σ1=-σ2=2σ3   To Find: (a) Yield stress of the material…

Q: What does the stator entry flow angle mean? why is the relative velocity and absolute velocities in…

A: To explain: What does the stator entry flow angle mean? why is the relative velocity and absolute…

Q: A crate of mass 2 kg is being lifted by a force described as F = 2s +25 where s is displacement in…

A: The mass of the crate,(m)=2 kg The value of the force ,(F)=2s+25 Determine the velocity of the crate…

Q: Which of the following statement is correct about miller indices for planes and directions? a.…

A: (a) Planes and their negatives are identical: This statement is incorrect because the Miller indices…

Q: What are two limitations for the following test methods? (80 - 100 Words) a. Compression test - Dry…

A: a. Compression test - Dryb. Compression test - Wetc. Leak-down testd. Oil pressure teste. Vacuum…

Q: 5. Knowing that the central portion of the link BD has a uniform cross sectional area of 800 mm²,…

A:

Q: b) At time t= 0 the height of water in the tank is h0. Find an expression for the height as a…

A: For the solution refer below images.

Q: Q2. For a specific spring where the load applied is 100 N, coil diameter is 4 mm, spring diameter is…

A: Given:Applied load (F) =100 NCoil diameter (d) =4 mmSpring diameter (D) =20 mmTo Find: Radius of the…

Q: 8.22 Steam heated at constant pressure in a steam generator enters the first stage of a…

A: P1=28 MPaT1=520°CP2=6 MPaT3=500°CηP=82%ηI=78%P=6 KPaTo fing:The quality of the steam at the exit of…

Q: Determine the elongation (in mm) of the square hollow bar, of 250 mm outer dimension and 30 mm…

A: Outer dimension, a = 250 mm Thickness, t = 30 mm Axial force, P = 103 kN Length, L = 2.5 m or 2500…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: 6-2) Determine the force P for impending sliding motion of the wedge to the left if the angle of…

A: Hi,     As per the guidelines, we can provide only typed solution not the handwritten solution. So,…

Q: A force of 280 N is sufficient to keep a 90 kg wooden block moving at a  constant velocity across a…

A: Given:Force on the block, F=280 NMass of the wooden block, m=90 kgFind:The coefficient of friction…

Q: A drill rod is used with an air hammer for making holes in hard rock so explosives can be placed in…

A: The impulsive force is a kind of force that only acts on an object for a brief period of time.

Q: Show the State of Stress at point m, on an element 30° rotated from the beam axis and on Mohr's…

A: Given: θ=30o W6×12 To find: State of stress at point m

Q: Can you pls slove this question briefly with hand written notes and diagram

A:

Q: 1) The 1.62-oz golf ball is struck by the five-iron and acquires the velocity shown in a time period…

A:

Q: For 10-2 above, the last part of Step 6 and the final answer seems to be missing or cut off on my…

A:

Q: P2.140 The U-tube in Fig. P2.140 is moving to the right with variable velocity. The water level in…

A:

Q: Problem 5.46 The flow of oil through the pipe is 0.041 m³/s. Take Po = 875 kg/m³ Pw 1000 kg/m³.…

A:

Q: Given a 2m-length rod with 23.0 mm diameter what is the actual stress (in MPa) if axial load is…

A: Given data :- The length of the rod (L) = 2 m                         The diameter of the rod (D) =…

Q: Determine the x and y components of reaction at the pin A. Express your answers using three…

A: Given:F=50 kNFind:Part A: The x and y components of reaction at the pin APart B: The tension in cord…

Q: A reservoirs water level is 200m above a pelton wheel jet. If the jet diameter is 20mm and the…

A:

Q: A carnot heat pump is being evaluated for the purpose of heating a residential area situated in an…

A: The minimum temperature of the cycle,(TL)=-35oC=-35+273=238 K The COP of the heat pump,(COP)=1.5…

Q: Problem 07.007 - Internal forces on members of a bow - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL…

A:

Q: The exact expression for the local Nusselt number for laminar flow along a flat plate is given by:…

A:

Q: If you have a velocity triangle for a rotor, what is the stator blade angle?

A: To explain: If you have a velocity triangle for a rotor, what is the stator blade angle?

Q: Two identical rods ABC and DBE are connected by a pin at B and by a spring CE. Knowing that the…

A:

Q: Determine the support reaction and draw the relationship between load, shear and moment diagram…

A:

Q: A pressure vessel of 225-mm inner diameter and 6-mm wall thickness is fabricated from a 1.2 m…

A:

Q: Which parameter is not involved in the linear impulse and momentum equation? a. Velocity b.…

A: Impulsive Force: 1. The impulsive force is the amount of force that's needed to cause a certain…

Q: 5.) Determine the thickness of a outside diameter of 100 mm hollow shaft having an if it is…

A: According to the given data T=5403.58 N.m D=100mm τ=60 Mpa G=83 GPa θ=0.5°  per meter length of the…

Q: m A roller coaster car and passenger with a mass of m = 800 kg starts at point A with a speed of V₁…

A: Dear Student since you have posted a question with multiple sub-parts, but as per Q& A…

Q: E. A particle traveling in a circular path of radius 300 m has an instantaneous velocity of 30 m/s…

A: Given data is shown below. r=300 mu=30 m/sat=4 m/s2   It is required to determine the magnitude of…

Q: Determine the Interplanar spacing and the length of the Burgers vector for slip on the preferred…

A:

Q: The state of stress at a point in a member is shown on the element below. If: 0x = 9 MPa Oy=-14 MPa…

A:

Q: The dimensions of the section are: l=55 mm, h=22 mm The triangle: hT=12 mm, lT=19 mm and the 2…

A: Dimension of Rectangular block  : (55mm,22 mm) Area of the  rectangle :  A1=55×22=1210mm2 Dimension…

Q: 8. As the linkage rotates, box A undergoes a) general plane motion c) linear translation b) pure…

A: In this four-bar mechanism, (s+l=p+q) has pair  of equal lengths, so this is a parallelogram…

Q: Steam at 1.4 MPa initially has a temperature of 200C. It was then cooled until all of it was turned…

A:

Q: What is the critical value of G for the directional solidification of two Al-Cu alloys (one…

A: Here, Rate of super conductivity ,v=0.08 mms . Partition coefficient , k=0.14. m=-2.6°Cwt%.…

Q: An external wall of a building has a U value of 0.50 W/m^2K. The indoor temperature is 21 degreesC…

A:

Q: 1. The linear impulse and momentum equation is obtained by integrating the time. a. friction force…

A: Solution.jpg

Q: The 63-mm diameter shaft is subjected to the torques as shown. Determine the angle of twist (in…

A:

Q: Consider the shaded area shown in (Eigure 1). Suppose that a-140 mm, b-150 mm, and r= 75 mm. Figure…

A: According to the given data We need to find Moment of inertia about the y-axis

Q: An unmanned submarine is equipped with temperature and depth measuring instruments and has radio…

A: Temperature variation,Tx=T0-0.01xVelocity, v=0.5m/sTemperature of water at sea surface, T0=20°C

Q: A refrigerator working on an ideal closed reverse Brayton cycle operates between 100,000 Pa and…

A:

Lubricants

Lubricant can be expressed as the substance that is applied among surfaces to control the wear and tear and improve performance. Lubricants play an essential part in the safety of machinery components like gears, shaft, linkage, cam, clutches, and many others. The quantities which affect the amount of lubricant are temperature, surrounding conditions, speed of the components, and many more.