Consider the balanced three-phase circuit is given below. The voltage values indicated are rms values. Assume that the line to line voltage at the source are given by Va = 420230°Volt(rms). (a) Calculate I4 (b) Calculate the line-to-line voltage of the load Vg - (c) Calculate the total complex power S, of the three-phase load. a ZLine A ab 72 b ZLine В 72 са ZLine C Source Line Load ZLine=1+j1 Z=15+jl5

Consider the balanced three-phase circuit is given below. The voltage values indicated are rms values. Assume that the line to line voltage at the source are given by Va = 420230°Volt(rms). (a) Calculate I4 (b) Calculate the line-to-line voltage of the load Vg - (c) Calculate the total complex power S, of the three-phase load. a ZLine A ab 72 b ZLine В 72 са ZLine C Source Line Load ZLine=1+j1 Z=15+jl5

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
Power factor correction is usually done by adding _________ to the load circuit.Select the correct response:a. switchb. capacitorc. inductive loads
6.5% ans ex A so kvA. 2o00/20 V, So He single-phase transformar has impedance drof of8% and resistance drop of 4%. Caleulate. The Requlation of the Thams former at full- Load o8 P.s Legging. also find The Power factor at which Voltage requlation will Be Zero. Sols 0.5 leading. s alculate The % Noltege Requlation af atransformar in w hich the Percantage resistance drof is 1% and Percentage dre is 6% when The Power fador is 0.8 lagging ) > unity aMS 38 % ans 1 % (シ→ 0.8 leading . amS - 2.2%
4. An Open-Wye/Open-Delta transformer, as shown in Figure, is formed by two identical single-phase transformers. The primary line-to-line voltage is 12.47 kV, and the secondary line-to-line voltage is 208 V. Take
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
2) The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S2=15.93 MW - j33.4 Mvar, and at bus 3 is S3-77 MW + j14 Mvar. It is required to hold the voltage at bus 3 at ...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu S₂ Figure V3 S3
In a given system of base power of 250 MW, and bus 3 is taken as reference. The per-unit reactances are X12 = 0.2 p.u., X13 = X23 = 0. 1 p.u. The power flow in the system is given as: PF12 = 50 MW, PF13 = 150 MW, PF23 = 50 MW. Based on readings from 2 meters (not including M12 meter), M13 = 145 MW (not calibrated), and M23 = 50 MW (well calibrated), deduce the flow on line 1-2. Select one: O a. PF12 = - 47.5 MW. O b. None of these O c. PF12 = 67.5 MW. O d. PF12 = 47.5 MW. O e. PF12 =- 57.5 MW. O f. PF12 = 57 MW.
Explain the concept of FACTS (Flexible Alternating Current Transmission Systems) devices. How do they enhance the control and stability of power systems? Provide examples of FACTS devices and their applications.
Consider a 3-phase, 50 HZ, 11 KV distribution system. Each of conductors is suspended by an insulator string having two identical porcelain insulators. The self-capacitance of the insulator is 5 times the shunt capacitance between link and ground. Find the voltages across two insulators.
A three-phase balanced load of 15A per phase is supplied by a steel wire armoured cable with a c.s.a. of 2.5mm². The voltage drop for this cable is 15mv/A/m and the circuit is 40m long. Calculate the voltage drop in the cable.