Complete the table below. STATION BM1 A B C D E F BM2 BS 1.470 1.967 2.792 2.225 2.209 1.072 Highest elev of the line of sight Station with the highest elevation (excluding BM1 & BM2) Lowest rod reading Station with the Highest BS Lowest Elevation HI 368.382 369.414 370.245 370.780 370.278 371.138 FS 1.200 1.136 1.082 3.400 0.212 1.204 ELEV 367.182 368.278 369.163 368.555 368.069 369.934

Complete the table below. STATION BM1 A B C D E F BM2 BS 1.470 1.967 2.792 2.225 2.209 1.072 Highest elev of the line of sight Station with the highest elevation (excluding BM1 & BM2) Lowest rod reading Station with the Highest BS Lowest Elevation HI 368.382 369.414 370.245 370.780 370.278 371.138 FS 1.200 1.136 1.082 3.400 0.212 1.204 ELEV 367.182 368.278 369.163 368.555 368.069 369.934

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

On the drawing below, the virtual condition of the 4 holes is? O .450 .375 O.395 O .020 D O .430 Ø3.000 .020 0 10 45° 4X Ø.395-.430 Ø.500-.510 Ø.020MABMCM +0.010M ADM Ø2.000 .375-.395 4.000MABM C A 0.005MA B
Determine the force of all members using METHOD OF JOINT. Answer in 3 decimal places only. TRUSS MEMBERS ● FORCE COMPRESSION OR TENSION
200kg 12 wedge A 2865 N B) 2685 N 2391 N
Find the equal height of towers at triangulation stations A and C so that line AC will clear theelevated ground between A and C by 6m. with the instrument set at point B, the observedvertical angle to ground station A is 0 0 55’ and the vertical angle to ground station C is 0 0 48’.Elevation of A is 237m. Distance AB is 10km and distance of BC is 8.7km. Yhe instrument set-upat B is 2.7m above the ground. Use hcr= 0.067k ^2
O O 9:0V Mark u out or1o ?What is the elevation of point BM1 in the below table if you know that the elevation of BM2 is 26.89 m Elevation 77? Elevation of BM2 FS HI BS Point No 1.532 BM1 1.873 BM2 الجواب 28.76 II The correct answer is: 27.231
Q3: A: Draw the diagram of traverse classification. B: In closed traverse ABCD. The partial coordinates were known as shown below. Determine its area by DMD method. 04 N Dofland OWODY dienstl it with (nm) dinostim Mem. AB BC CD DA ΔΧ 40 -80 -50 AY 60 100 -70
12. INTERVISIBLITY OF STATIONS. Cathedral Hill is on á line between Constable Hill and. Aurora Hill. Cathedral Hill is 6.253 km from the Constable Hill and Aurora Hill is 11.081 km from the Constable Hill. The elevation of the hills are: Constable Hill, 1260.86m; Aurora Hill, 1266.44m3; and Cathedral Hill, 1261.04m. Determine the following: a) Elevation of the line of sight from Constable Hill at the vicinity of Cathedral Hill. b) Height of identical towers to be constructed at Constable Hill and Aurora Hill so that the line of sight will clear Cathedral Hill by 5.0m. c) Height of tower to be constructed on Constable Hill so that the line of sight will clear the ground at Cathedral Hill by 5.0m, if no tower is to be constructed on Aurora Hill. d) Height of tower to be constructed on Aurora Hill so that the line of sight will clear the ground at Cathedral Hill by 5.0m, if no tower is to be constructed on Constable Hill.
Transit is set up at A observeda stadia intercept of 2.2 m at a verticalangle of +1823’. The stadia interval factor ofthe instrument used is 95.5 and stadiaconstant of 0.3 m. If the height of instrumentis 1.62 m, and the rod reading is 1.95 m.Determine the horizontal distance from thetransit set up A to the rod at point B. a. 201.44 m c. 198.45 b. 189.48 m d. 186.56 m
8. Compute for the following and show the tabulated solutions: Azimuth LINES Length (S) АВ 1020.87 168d35m ВС 1117.26 263d30m CD 660.08 304d25m DE 495.85 5d30m EF 850.62 46d15m FA 855.45 112d30m (lengths in 3 dec. places; bearings in deg-mm-ss) a. Using Transit Rule, solve for adjusted latitudes, departures, distances, and bearings for all the traverse lines Lines Adj. Latitude Adj. Departure Adj. Length Adj. Bearing AB BC CD DE EF FA
If the 4 holes in the drawing below are produced at .410" in diameter, what is the total positional tolerance of the holes? O .040 O .020 O .035 D O .410 Ø3.000 .020 45° 4X Ø.395-.430 Ø.500-.510 0.020MABMCM +0.010M ADM -.375-.395 +.000MABM C Ø2.000 A 0.005MA B
Convert N 25 deg 25 min W to an equivalent azimuth from North O 154 deg 35 min O 334 deg 35 min O 25 deg 25 min O 145 deg 35 min
SITUATION 1- Hissing Data Given: Traverse with omitted measurements. (a) Calculate the distance of line GA (b) Determine the bearing of line CD TRAVERSE DATA W/ OHITTED MEASUREMENTS UNE LENGTH (m) BEARING AB 550.00 S 80.00° W BC 295.00 N 40.00° W CD 610.00 DE 885.00 S 72.00° E EF 455.00 S 18.00° E FG 500.00 S 80.00° W GA N 30.00 W