Classify each soil according to ASSHTO classification system.DescriptionPercent finer than No.10 SieveSOIL ASOIL BSOIL C8310048Percent finer than No.40 Sieve489228Percent finer than No.200 Sieve20866.Liquid LimitPlasticity IndexN/ANon plastic2070532

Answered: Image /qna-images/answer/dfd5578e-1e98-47c7-bc43-d7a575649fa2.jpg

Classify each soil according to ASSHTO classification system. SOIL A SOIL B Description Percent finer than No.10 Sieve SOIL C 83 100 48 Percent finer than No.40 Sieve 48 92 28 Percent finer than No.200 Sieve 20 86 Liquid Limit Plasticity Index N/A Non plastic 20 70 32

Classify each soil according to ASSHTO classification system. SOIL A SOIL B Description Percent finer than No.10 Sieve SOIL C 83 100 48 Percent finer than No.40 Sieve 48 92 28 Percent finer than No.200 Sieve 20 86 Liquid Limit Plasticity Index N/A Non plastic 20 70 32

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: What is the type of this truss

A: Solution: There are different types of trusses used in the construction field like Howe Trusses Fli...

Q: Sketch for the influence lines for the vertical reaction at A, shear at C and moment at C. B F6-1 F6...

Q: A soil sample has moisture content of 30% and degree of saturation of 45%. The solids have specific ...

Q: A tripod shown supports a load of P = 1000 N at point A. Take note that ball and socket joints are u...

Q: A hydraulic jump is formed in a 2 m wide rectangular channel carrying water at a flow velocity of 16...

Q: Maximum strain in concrete taken for design is 0.0040 while strain in deformed bar is calculated wit...

Q: Draw the shear and moment diagram using area method.

Q: The perimeter of a triangle is 46 centimeters. The longest side is 3 centimeters less than twice the...

A: Perimeter of triangle=46 cm Let the length of longest side is c, length of shortest side is a and le...

Q: 3. fa 400N force is applied to the short bracket shown below interpret the load as a force and a mom...

Q: Field density testing (e.g., sand replacement method) has shown bulk density of a compacted road bas...

Q: Passenger cars arrive at the stop sign at an average rate of 280 per hour. Average departure time at...

A: Given data: Mean arrival rate =280 vehicles /hour Mean service rate=3600/12=300

Q: In the given beam, ρactual = 0.00254, and ρbalance = 0.00221. What kind of beam is this?

Q: 3. Determine the X and Y-components of the forces shown in the figure.

Q: Prob. 2 For the given loading, determine the zero-force members in the truss shown.

A: To Determine For the given truss, which of the following members are carrying zero force / no force....

Q: Need answer ASAP. Please be detailed and clear with your solution. III. Shown is a parabolic segmen...

Q: A wide rectangular channel has a Manning's coefficient of 0.018. In a discharge intensity of 1.5 m³/...

Q: Determine the X and Y -components of the forces shown in the figure.

A: To determines the X and Y components of the shown forces. Given, Magnitude of force F1 = 70 lbs Ma...

Q: L/2 ि ৪ 3L/2 L - 1- Determine the number of degrees of freedom;

A: The number of free displacement at joint is known as degree of freedom

Q: A slender homogenous wire of uniform cross section is bent into the form shown. Determine the positi...

Q: Determine the OM ¸ for the cross section that has a rectangular duct cast in it, as shown. Use =21 M...

Q: Draw the shear and bending moment curves for the beam and loading and the maximum absolute value of ...

Q: Q 31 The following Easting and Northing for a closed traverse is Station X (Easting) Y (Northing) 1 ...

Q: For question 3.5, the vertical deflection of joint B is approximately equal to 0.0942m 0.1246m 0.069...

Q: 75. A 6 m long timber beam 220 mm wide by 400 mm deep is simply supported at its ends and carries un...

A: Determine allowable uniform load,W=?

Q: Analysis of determinate frames. Draw the normal, shear, and moment diagram of the loaded frame and a...

Q: A rectangular beam for a 6 m simple span to support a uniform dead load of 15 kN/m and live load act...

A: Note - Steel ratio is .45% which is a justified value.

Q: What is the value of reduction factor of the beam, if the stress in the steel is 400 MPa, and the Mo...

Q: A differential levelling was conducted from BM1 to BM2 30 km apart. BM1 is at elevation 124. 08 m. T...

Q: AE Constant Solve for vertical displacement @ jeintc. in terms of AE. Indicate štN the direction. 20...

Q: Saturated clay encountered in a deep excavation is found to have a water content of 28%. Determine t...

A: We will use formula of saturated weight.

Q: At an impaired driver checkpoint, the time required to conduct the impairment test varies (according...

A: Given Data, Average Flow rate arriving = 30 vehicle/hr Average time spend on test = 60 seconds

Q: The hoisting gear A has an initial angular velocity of 60 rad/s and a constant deceleration of 1 rad...

Q: Field density testing (e.g., sand replacement method) has shown bulk density of a compacted road bas...

Q: A vertical sag parabolic curve has a length of curve of 420 m. from A to B. The back tangent has a s...

A: We have to determine the value of elevation of point A as per the given data in the question like gr...

Q: The estimated common excavation for the driveway is 420 cubic meters and there are also 32 footings ...

Q: The Figure below gives an example of a network to pump water from a lower reservoir to an upper one....

A: Quantity of water required in a building per day is calculated by number of inhabitants multiplied b...

Q: . A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement ...

Q: Question 3: For an inorganic soil the following grain - size analysis is given. U.S sieve Percent an...

A: Given data - THE SIEVE ANALYSIS IS GIVEN AS - To find - Classification based on 1 - AASHTO 2 - U...

Q: Compute the design moment strength of the section shown below if f. = 40 MPa and f, = 500 MPa . - 30...

Q: Draw the shear and bending moment curves for the beam and loading and the maximum absolute value of ...

Q: Field density testing (e.g., sand replacement method) has shown bulk density of a compacted road bas...

Q: 120 kN/m 80 kN/m 5 m :/- 3 m - For the beam shown in the figure, determine the magnitude of the maxi...

Q: 1000 lb 500 lb/ft 3800 lb/ft B E D. 2 ft 2 ft 2 ft 6 ft Shear Equation Moment Equation Segment AB Se...

Q: SITUATION: For the beam shown, 9. Determine the vertical reaction at A in Ib. a. 531 -3 ft- -9 ft- b...

Q: Three planks of wood were joined together to form the T-section shown in figure A. The beam is the s...

Q: A steel shaft with a diameter 1.85 inches and length 4.25 feet transmits 75 HP from an electric moto...

Q: According to the loading system shown in the figure, if P = 120 N, If the resultant moment of all fo...

A: Find value of F=?

Q: A wide rectangular channel has a Manning's coefficient of 0.018. In a discharge intensity of 1.5 m3/...

Q: . If the footing shown below is not to settle more than 1 in., what is the maximum load it can carry...

Question

Classify each soil according to ASSHTO classification system.
Description
Percent finer than No.10 Sieve
SOIL A
SOIL B
SOIL C
83
100
48
Percent finer than No.40 Sieve
48
92
28
Percent finer than No.200 Sieve
20
86
6.
Liquid Limit
Plasticity Index
N/A
Non plastic
20
70
5
32

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

• Problem 1- . Classify the soil to be used as a highway subgrade material using AASHTO classification system; Sieve No. No. 4 No. 10 No. 20 No. 40 No. 60 No. 140 No. 200 Size opening (mm) 4.75 2.00 0.850 0.425 0.250 0.140 0.075 % Finer 100 92 84 69 50 40 37 Liquid limit for soil passing # 40 sieve was determine to be 40% and plasticity index was 20%.
Do the following: a) Calculate the percent retained and percent passing each sieve, and graph the results on a semi-log graph (you may use the attached chart, or graph in Excel and include with your submission). Then, characterize the gradation of the material. b) Calculate the values of D10, D30, D60, Cu, and Cc c) If the LL is 48 and the PL is 26, determine the USCS classification of the soil, and state its suitability for the purpose stated in the scenario.
Calculate the AASHTO group index number of the following soil Liquid Limit = 36% Plastic Index = 14% Sieve analysis data: US Sieve Size % Passing No. 10 72 No. 40 61 No. 200 33
Based on the sieve analysis a soil has % finer for the following sieves: No. 10- 90% ; No. 40- 48% and No. 200- 22%. The liquid limit and Plasticity index is 5. Classify the soil by AASHT0 classification and give also the group index. a. A-2-7(1) b. A-2-6 (0) c. A-3 (0) d. A-1-b(0)
Soil Mechanics Based on the sieve analysis a soil has % finer for the following sieves: No. 10- 90% ; No. 40- 48% and No. 200- 22%. The liquid limit and Plasticity index is 5. Classify the soil by AASHT0 classification and give also the group index. a. A-2-7(1) b. A-2-6 (0) c. A-3 (0) d. A-1-b(0)
Based on the sieve analysis a soil has % finer for the following sieves: No. 10- 80% ; No. 40- 68% and No. 200- 48%. The liquid limit is 30 and Plasticity index is 11. Classify the soil by AASHT0 classification and give also the group index.a. A-6 (2) b. A-7-5(8)c. A-6 (9) d. A-7-6(8)
up to 120221 (Compatibility Mode] - Word References Mailings Review View Help Nitro Pro V Tell me what you want to do A A Aa E E-E EE T T 2 T AaBbCcl AaBbCcI AABBCCI A A、ッ、A 前,, Emphasis T Heading 1 I Normal Paragraph Styles 1. Q. The following results were obtained from a CBR test on a compacted subgrade soil. Calculate the CBR value for the soil. Do you recommend to use it as subbase? Illustrate your answer? Penetration (mm) Load (KN) 0.625 0.15 1.25 0.18 1.875 0.40 2.5 0.73 3.75 1.32 1.80 7.5 2.34 10 2.53 12.5 2.91 Standard Loads: 2.5 mm .... .13.36 KN 5.0 mm 19.96 KN tes) lenovo
Based on the sieve analysis a soil has % finer for the following sieves: No. 10- 86% ; No. 40- 56% and No. 200- 8%. No Plasticity. Classify the soil by AASHTO classification and give also the group index. Oa. A-1-b(0) Ob. A-3 (0) O c. A-2-6 (0) O d. A-2-7(1)
For a given sieve analyis: No. 4 - % finer 100%, for No. 200 -%finer 45. LL=36, PL= 22. Classify the soil using USCS. Justify your answer. a.SM b.SC c.SM d.GC
For a given sieve analyis: No. 4 - % finer 100%, for No. 200 -%finer 45. LL=36, PL= 22. Classify the soil using USCS. Justify your answer. CHOICES: a.SC b.GC c.SM d.SM
PROBLEM NO. 2 A fined grained soil (no sand) is found to have a liquid limit of 70%, and a plastic limit of 38%. 70 CH 60 PIOLL- -line RZ0.73(L 20) CL U-e 10 OL 30 MH -CL- ML 10 ML OH or OL 10 16 20 30 40 $0 70 80 Liquid limit a. What is the plasticity index for this soil? b. On the plasticity chart for USCS, what soil type is 90 100 this? c. On the plasticity chart for the AASHTO Classification System, what soil type is this? Plasticitý index
2.Determine the percentage of Gravel, Sand, Silt, and Clay and determine the value of Cu and Cc for soil: Soil A and Soil C 100 80 60 40 20 O 100- > 0.0001