Calculation for drive system and rack/spur gear of a crane. System needs to able to climb an incline of 12.457 beam tilt from horizontal With a payload weight of 27,500 lbs. using a 2 hp motor, 1725 rpm, 60 hz Gear reducer with 8.5 output rpm, ratio 204.75 Drive speed of 2.238 in/s Tooth force of 5931.798 lbf Rack - 20 PA, 2.5" face width, 1.5" thickness, 6' length, diametral pitch 5 in, 1018 steel Spur gear - 2.5" face width, diametral pitch 5 in, 20 PA, 30 teeth, 6.4 OD, 6 PD, 1144 steel Will this system work?

Calculation for drive system and rack/spur gear of a crane. System needs to able to climb an incline of 12.457 beam tilt from horizontal With a payload weight of 27,500 lbs. using a 2 hp motor, 1725 rpm, 60 hz Gear reducer with 8.5 output rpm, ratio 204.75 Drive speed of 2.238 in/s Tooth force of 5931.798 lbf Rack - 20 PA, 2.5" face width, 1.5" thickness, 6' length, diametral pitch 5 in, 1018 steel Spur gear - 2.5" face width, diametral pitch 5 in, 20 PA, 30 teeth, 6.4 OD, 6 PD, 1144 steel Will this system work?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A belt conveyor transports 18 tonnes per hr at 20°. Calculate the height in m to lift the load vertically up sufficient to give 33.5 m inclined belt length. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
A rotating slurry pump is to be driven by a 50hp, 2400 rpm diesel engine and operating under moderate shock load. The pump will operate at 800 rpm. The recommended small sheave diameter is 6 inches. Calculate the following: A. The large sheave diameter B. The minimum type of V-belt to recommend. C. Minimum recommended length of belt. D. Actual center distance E. Number of v-belts Refer to book of faires please.
A belt conveyor transports 18 tonnes per hr at 20°. Calculate the hp requirement to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
A belt conveyor transports 18 tonnes per hr at 20°. Calculate the total length to be sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley.
A belt conveyor transports 18 tonnes per hr at 20°. Determine the unit weight of belt material in kg/ply-cm width-m to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
A 1000 RPM speed reducer and 12KW power drives a conveyor belt at 400 RPM. the distance between the centers is approximately 800mm. Select a suitable chain for transmission, as follows:1) Solicitation with moderate shock, abnormal operating conditions, operating 24 hours a day.
The specifications for the Gear Pump are, Discharge-40 LPM, Pressure-50 bar i. By making suitable assume ii. Select suitable standard motor. iii. Design gear and check for bending failure, dynamic load and pitting. iv. Find the resultant force acting on the heavily loaded shaft.
QUESTION 10 A motor-cycle engine crankshaft has an angular velocity of 523.6 rad/s and is in third gear of ratio 1.62:1. The final chain reduction is 4.7:1 and the effective wheel diameter 0.73 m. Calculate the road speed of the machine in km/h.
Calculate the principal data for a 10.7 m horizontal screw conveyor for 2.7 tonnes coal per hr, about 60 rpm. Worm gear speed reducer, 1750-rpm motor.
A slurry pump is to be driven by a 50 HP, 2400 rpm diesel engine and operating under moderate shock load with service factor of 1.20. The pump will operate at 800 rpm and using type B V-Belt. The available small sheave diameter is 5.4 inches and having a factor of 1.14. The arc of contact factor is 0.79 and the length of belt factor 0.87. Find the no. of belts used.
What is the extreme transmission angle values by using maxima and minima condition, of the transmission angle occur when the crank is perpendicular to the slider path in a slider-crank linkage.