Calculate "terminal" phase voltage of phases "a" and "c" of generator.Calculate Vab and Vca across the load.Calculate three phase power supplied by the source.]Calculate three phase power losses. A Y-connected balanced three-phase source is connected to a three-phase balanced load through a four-wire three-phase cable. The generator has an impedance of 0.1+j0.3 0/phase. Each phase of the cable has animpedance of 2+2j Q. The phase "B" load voltage is 102-140° kV. The impedance of each phase of the Y-connected load is 3-j5 0/phase. For a negative sequence:

Answered: Image /qna-images/answer/7943c57b-0950-4340-af36-fa357d3bfd66.jpg

Answered: Calculate "terminal" phase voltage of…

Calculate "terminal" phase voltage of phases "a" and "c" of generator. Calculate Vab and Vca across the load. Calculate three phase power supplied by the source. ]Calculate three phase power losses.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.56P: Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit...

See similar textbooks

Related questions

Q: What is load line and what is duty cycle?

Q: For the same voltage and current produced by a three phase and single phase source, the power…

A: In this question, We need to choose the correct options Choose the given Statment is true or false?…

Q: Write an introduction about: LOAD BALANCING in 3-Phase System

A: Three-Phase System - A three-phase system is formed out of a three-phase voltage source that is…

Q: he Fig shows the single line diagram of a single phase circuit. Using the base values of 3 kVA and…

A: Given: Base Values: 3 kVA, 230 kV at generator side. Line impedance XTL=2 Ω, Load impedance…

Q: Figure 1 shows a generating station feeding power to a system. This line is 200 km long. What is the…

Q: A three-phase, wye-connected, 7 kVA, 230 V synchronous generator has a reactance of 7 ohms per…

A: Base impedance=Voltagecurrent =Voltagecurrent×voltageVoltage…

Q: please write introduction about Analysis of 3 Phase star connected circuit Note:please write details…

Q: Generators generate positive sequence voltage only False True

A: Positive Sequence: The positive sequence is a three-phase balanced system in which the system has…

Q: The value of value of voltage measured in residential convenience outlet is average voltage. True…

A: Average value is the average of the signal over the period of time. Where as rms value of the signal…

Q: Q2:- a synchronous generator is 25 MVA, 11kV, it is star- connected with the neutral point solidly…

A: Given:X1=X2=0.2puX0=0.08pu Consider power base is 25 MVA and voltage base is 11 KVVoltage PU =1

Q: (a) If a three-phase synchronous generator voltage output is the same with its per-phase voltage,…

A: The solution is given below

Q: 1.2 For each set of voltages, state whether or not the mCE voltages form a balanced three-phase set.…

A: The explanation is as folows.

Q: 16. Which of the following is a solution to the problem of circulating currents? A. Integrating the…

A: Circulating currents are generated due to asymmetry in the motor and the voltage it creates between…

Q: The positive-, negative-, and zero-sequence reactances of a 15-MVA, 11-kV, three-phase, wye-…

A: Given data about a three phase, wye-connected generator is, Positive sequence reactance X1=11%=j0.11…

Q: Phase Advancer for power factor improvement. and What is penalty factor? Derive the expression for…

Q: The one line diagram of power system is shown in Figure Q.1. Use a common base MVA of 100 MVA and…

Q: Describe the eviromental considerations for the different power plant types.

A: Different energy sources are required in day-to-day life. These energy sources can be renewable or…

Q: Write about voltage drop and power loss for Radial d.c distribution system.

A: In the radial dc distribution system, various feeders are connected to the single substation such…

Q: For two parallel synchronous generators of the same size and same droop in frequency-Active Power…

A: for two parallel synchronous generators of the same size and same droop in frequency active power…

Q: Provide concise answers for the following questions a. Why is it preferred to use the pu system in…

A: derivation for Per unit impedance, if a change of base occurs is derived as shown below.

Q: 2- The Purpose of using Unbalanced Three-phase Systems: Ji

A: Need to find purpose of using unbalanced three phase system

Q: Mention and discuss the uncertainties affecting the power system operation and planning indices.

A: Uncertainty is associated with the massive power generation of the renewable energy. The renewable…

Q: a). What is the reason for providing sag in an Overhead transmission line? b). List any two…

A: Whenever there is a need to send electricity to far off long distances, then the usage of overhead…

Q: 3. A 100 MVĂ, 33KV 3-phase alternåtör current are as under: 3-phase fault-2000A, Line to Line…

A: Please refer the attached images for the complete answer..

Q: What is the per unit impedance of a 50 MVA, 13.8 kV, 1% impedance transformer if the base is change…

Q: 10. The full-load losses in a 5,000-kva three-phase 6,600-volt synchronous condenser are 160 kw.…

A: For the above given question we need to calculate the value of full load current and power factor of…

Q: In an unbalanced three phase system, having balanced supply phase voltages are separated by 120°…

A: The objective is to determine the correct option.

Q: for the same alternator, the ratio of rated KVA when connected as 3-phase winding alternator to when…

A: For 3-phase connection of the windings, the phase spread will be ψ=π3=60o So, distribution factor…

Q: In single phase system, the performance of motor produces the uniform torque. Select one: True…

A: We need to tell about the given statement is true or false.

Q: (b) Explain the steps involved in analysing balanced bolted fault in power system using Zbus method,…

A: Admittance matrix and impedence matrix is very important to analyze the power system .Admittance…

Q: 2. Contribution of load flow studies to erect new power station?

A: A power system is modelled by an electric network and solved for steady state power and voltages at…

Q: Write a conclusion about voltage drop and power loss calculations for Ring d.c distribution system.

A: Ring DC distribution system: It is the system for distributing the power. In this system, the first…

Q: B) State the main points that should be taken in to account in selection of number and sizes of the…

A: B) The main points that should be taken into consideration while selecting the number and the sizes…

Q: Prepare a capacity outage Probability table for a 3 generator system with each having a capacity of…

A: The generating system consists of three plants each having, Capacity=50 MW Forced Outage…

Q: 7. Which of the following are sometimes installed as an emergency system, legally required standby…

A: In this question, Choose the correct option Which of the following are sometimes installed as an…

Q: Explain two-wattmeter method for star-connected three phase balanced circuits. Also derive the…

A: Two-wattmeter method: Two Wattmeter Method can be implemented to estimate the power in a 3 phase,…

Q: 2- The Purpose of using Unbalanced Three-phase Systems:

A: The purpose of using unbalanced three phase system is

Q: A three-phase, wye-connected, 6.25kVA, 220-synchronous generator has a reactance of 8.4 ohms per…

Q: A 3-phase, 11 kV, 5 MVA alternator has synchronous reactance of 10 per phase. Its excitation is such…

A: Given a 3-phase, 11 kV, 5 MVA alternator has, Synchronous reactance, X=10 Ω Voltage, E = 11 kV…

Q: positive sequence components having phase sequence the same as the * .original phasors true false…

A: The positive sequence is, The three sets of phasors are equal in magnitude in the positive sequence…

Q: A generating system contains three 20 MW generating units each with a 3% FOR and one 45 MW unit with…

A: A table for unit system capacity outage is shown below:

Q: Plot generator output voltage versus load current for operating conditions with and without…

A: Voltage regulator is a circuit designed to maintain constant voltage at the output. The following…

Q: Each line of a 3-phase system is suspended by a string of 3 similar insulators. If the voltage…

A: The solution can be achieved as follows.

Q: 6- Why it is possible to short circuit the differ tia generator and not the cumulative compound…

A: Compound generator consists of both series and shunt filed windings. If the flux produced by both…

Q: A 10 MVA, 6-6 kV, 3-phase star-connected alternator having a reactance of 20% is connected through a…

A: The last digits of student ID is 21. Given information We need to draw the transmission line and…

Q: A MVA, 20 KV, three-phašė ģenēřātor has a subtransient reactance of 20%. The generator supplies a…

A: Solution- For generator, S = 300 MVA V = 20KV X = 20% For motor 1, S = 200 MVA V = 13.2 KV X= 20%…

Q: In a 3-phase, 4 wire unbalanced system, the current in neutral wire is 18 A. The magnitude of zero…

A: Given a 3-phase, 4 wire unbalanced system having, The current in neutral wire, IN=18 A

Q: a) The one line diagram of a three phase system is shown below, draw an impedance diagram showing…

A: It is given that:

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

Calculate "terminal" phase voltage of phases "a" and "c" of generator.
Calculate Vab and Vca across the load.
Calculate three phase power supplied by the source.
]Calculate three phase power losses.

A Y-connected balanced three-phase source is connected to a three-phase balanced load through a four-wire three-phase cable. The generator has an impedance of 0.1+j0.3 0/phase. Each phase of the cable has an
impedance of 2+2j Q. The phase "B" load voltage is 102-140° kV. The impedance of each phase of the Y-connected load is 3-j5 0/phase. For a negative sequence:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

There is a three-phase system such that the phase current in the generator, lines and charging phase is the same. The phase voltage in the generator must be 1000 [V] with clockwise sequence. The connected load must be such that the phase current in each load is 10 [A] and its power factor is 0.97 “lagging”. a) Determine phase currents in the generator, lines and phase in the load
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
Q2 (a) Three-phase generator consist of three set of single-phase generators, with voltages equal in magnitude but differing in phase angle by 120° apart. (i) Sketch phasor diagram of the three-phase voltages VA, VB and Vc (ii) Plot the three-phase voltages waveform in Q2(a)(i) in single plot.
Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit leakage reactance, are connected as a three-phase extended autotransformer bank, as shown in Figure 3.36(c). The low-voltage winding has a 110 volt rating. (a) Draw the positive-sequence phasor diagram and show that the high-voltage winding has a 479.5 volt rating. (b) A three-phase load connected to the low-voltage terminals absorbs 6 kW at 110 volts and at 0.8 power factor lagging. Draw the per-unit impedance diagram and calculate the voltage and current at the high-voltage terminals. Assume positive-sequence operation.
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
Qa1. The three phases of a generator can be connected in either delia (D) or wye (Y) connection. List two advantages of three phase system over a single phase system. Also write mathematical relationship between the phase voltage and the ine voltage, and the phase current and the line current for both delia (D) and wye (Y) connections. Please answer in typing format please..
6. A 3 phase fault occurs at point F as shown in figure. Determine the critical clearing anglefor the system. The generator is delivering 1.0 p.u power under prefault conditio
7. An inductive load is shared by two identical synchronous generators A and Bequally, if the excitation of alternator A is increased. (a) Alternator A will deliver more current and alternator B will deliver less current. (b) Alternator B will deliver more current and alternator A will deliver less current. (c) both will continue to deliver same current. (d) both will deliver more current.
The one-line diagram of a simple power system is shown in Figure below. The neutral of each generator is grounded through a current-limiting reactor of 0.25/3 per unit on a 100-MVA base. The system data expressed in per unit on a common 100-MVA base is tabulated below. The generators are running on no-load at their rated voltage and rated frequency with their emfs in phase. G Stark Item Base MVA Voltage Rating X' x² 20 kV 20 kV 20/220 kV 20/220 kV 100 0.05 0.15 0.15 0.10 0.10 220 kV 0.125 0.125 0.30 0.15 0.25 025 0.7125 0.15 100 100 0.15 0.05 0.10 0.10 0.10 100 0.10 100 100 Lu La 220 kV 0.15 220 kV 0.35 100 A balanced three-phase fault at bus 3 through a fault impedance Zf= jo.I per unit. The magnitude of the fault current in amperes in phase b for this fault is: Select one: A. 345.3 B. 820.1 C. 312500 3888888 产产
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power
A generator is rated 100 MVA, 22 kV. Its Y connected windings have areactance of 1.1 per unit. Find the reactance of the winding. Then find a new per unit value of reactance of the generator for 100 MVA and 20 kV.
1. A single-phase power system as shown in Figure 1 consists of a 240 V, 60 Hz generator supplying a load, Zod = 8 + j6 Q through a transmission line of impedance, Zne = 0.08 + j0.14 Q. Answer the following questions: (1) transformer, T; and T2. Determine the voltage at the load and transmission line losses without the (ii) Determine the voltage at the load and transmission line losses with the transformer, T, and T2. T1 T2 1:10 10:1 IG Zaine Zioad source Figure 1