Q4 parts c & d please Q4.(a)Write brief notes (taking a maximum of 15 minutes) on RC filter circuits,including in your discussion:• The basic function of an electronic filter circuit.Simple RC circuits for low pass (LPF) and high pass filters (HPF).• The bode plots of RC LPFs and HPFs.• Why RC filters are more commonplace that RL filters.• One example application for each of the RC LPF and HPF.(b) Starting with the voltage divider rule, show that the power transmissioncoefficient T of an RC LPF is given by• - ~ =outVinT11+ (ƒ / ƒ)²³ ³fc =1 12₁ RC(c) Given a 50nF capacitor, calculate a suitable value of R to realise an RCLPF with a roll-off frequency fc of 3kHz.(d) For the RC LPF of Q4(c), calculate the output voltages (as phasors) forinput voltages of 12V amplitude at frequencies of 300Hz, 3kHz and30kHz. Plot these on a phasor diagram and hence explain whathappens to the amplitude and phase of the output voltage, relative tothe input voltage, when f >> fc.

Answered: Image /qna-images/answer/83907b75-ed09-4ae1-989a-0b47e56f1527.jpg

(c) Given a 50nF capacitor, calculate a suitable value of R to realise an RC LPF with a roll-off frequency fc of 3kHz. (d) For the RC LPF of Q4(c), calculate the output voltages (as phasors) for input voltages of 12V amplitude at frequencies of 300Hz, 3kHz and 30kHz. Plot these on a phasor diagram and hence explain what happens to the amplitude and phase of the output voltage, relative to the input voltage, when f >> fc.

(c) Given a 50nF capacitor, calculate a suitable value of R to realise an RC LPF with a roll-off frequency fc of 3kHz. (d) For the RC LPF of Q4(c), calculate the output voltages (as phasors) for input voltages of 12V amplitude at frequencies of 300Hz, 3kHz and 30kHz. Plot these on a phasor diagram and hence explain what happens to the amplitude and phase of the output voltage, relative to the input voltage, when f >> fc.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is the distinction in voltage attain of a lowpass filter if the enter frequency is doubled? What is the distinction in voltage attain of a lowpass filter if the enter frequency is expanded ten times? How do you assemble a band give up RC filter? Simulate a circuit and generate a desk to show your claim.
What is the definition of resonant frequencies, cut-off frequencies, bandwidth, andquality factor of series and parallel RLC circuits.And how do you determine the circuit conditions at the resonant and cut-off frequencies. (Answer in long paragraph form)
Explain how the resonant frequencies, cut-off frequencies, bandwidth, andquality factor of series and parallel RLC circuits works.And how to determine the circuit conditions at the resonant and cut-off frequencies. (Answer in long paragraph form)
What is the function of a low pass filter? Draw a diagram of a simple low-pass filter using a capacitor and a resistor.
Name four types of ideal filters and sketch their transfer functions.
Q4 Design an active highpass filter with a gain of 10, a corner frequency of 2 kHz, and a gain roll-off rate of 40 dB/decade.
4. A simple band-pass filter can be designed by cascading one-pole high-pass and one-pole low-pass filters. Using op- amp circuits similar to the one shown below, design band-pass filter with cutoff frequencies of 200Hz and 50 kHz and with a midband gain of 10dB. Resistor values must be no larger than 200k, but the input resistance must be as large as possible. Vic C oV₂ V₁ www OV
Design an active lowpass filter with dc gain of 0.5 and corner frequency of 250Hz. Then draw the circuit diagram for this filter.
(b) Analyse and obtain the transfer function for the filter as shown in Figure Q2(b). R₁ VW HH R₂ W Figure Q2 (b)
5. Why we use semiology paper to draw the frequency response of filters. 6. What is filter order, and what is the effect of changing filter order on the filter response and complexity of filter. 7 Sketch the frequency response of low-pass, band-pass, high-pass, and band-reject filters.
Briefly -Discuss the effect of increasing the order of the filter on the frequency response of the filter.
What is the transfer function of a filter? Describe how the transfer function of a filter can be determined using laboratory methods.