Q: Construct a flowchart for the separation of p-methyl benzoic acid, p-methylaniline, and napthaline…
A: The moving of compound from one solvent to another solvent by changing the PH is known as acid base…
Q: Give one lysis buffer that is commonly used for western blotting experiments and include its…
A: 1. Answer - The RIPA buffer (lysis buffer) is one of the most commonly used buffers in used for…
Q: Propose an experimental design on the separation of components of the mixture of o-nitrophenol and…
A: Mixture of o-nitrophenol and p-nitrophenol can be separated using Steam Distillation process. The…
Q: 1. What is the purpose of adding Na2SO4 to the dichloromethane layer prior to distillation 2.…
A: In liquid-liquid extraction, separation of compounds takes place on the basis of their relative…
Q: What solvent below would be able to be used in a liquid-liquid extraction where hexane…
A: Polar solvent dissolve polar compounds and non polar solvent dissolve non polar compounds.
Q: Answer ALL parts to this question (a) With the aid of a diagram describe the experimental set up of…
A: Answer- Gas chromatography- Gas chromatography is a term used to describe the group of analytical…
Q: What information can GC provide? **Select ALL answers that apply** a. boiling point b. Rf c. ratio…
A: GC is referred to as gas chromatography and is an analytical technique which is used to separate…
Q: Attached problem
A: If the coloration of the sample is not detected properly or if decolourization of sample occurs,…
Q: Explain exactly what you would do when performing the following laboratoryinstructions; that is,…
A: To Find: To explain what you would do when performing the given instruction.
Q: Which analyte gives a positive result for the Molisch Test?
A:
Q: LNH2 You have access to the following solutions for your experiment: 1 M NaOH 1 M HCI 1 M CH3COOH 1…
A: We would use liquid Liquid Extraction for the separation of following substances and acid base…
Q: If you would directly analyse a solid sample with AAS, which method will you prefer? Explain about…
A: Atomic absorption spectroscopy (AAS) is a spectroanalytical method for the quantitative analysis of…
Q: Suggest another way (besides vacuum filtration) to purify the partially oxidized benzaldehyde. 3.
A: We can purify the partially oxidised benzaldehyde as follows.
Q: 00 80 60 40 20 0 20 40 60 80 1
A: DISTILLATION Distillation is the process of selectively boiling a component in a liquid mixture and…
Q: Briefly explain the reasons for the use of the following techniques in this experiment. a. The…
A:
Q: Why is methanol chosen as the solvent for recrystallization? What would happen if the student uses…
A: Most of the organic compound is dissolved in alcohol like methanol and ethanol . methanol is easy to…
Q: After a crude product is dissolved in 1.5 mL of hot solvent, the resulting solution is dark brown.…
A: Activated charcoal can be extracted colored impurities from the solution. But the quantity to be…
Q: Write a full Procedure of Recrystallization of p-Nitroaniline.
A: Introduction: p-Nitroaniline is 1-amino-4-nitrobenzene. It is used in dyes, pharmaceuticals,…
Q: What is the reason for using as little ethanol as possible to dissolve the crude product before…
A: For recrystallization, it is recommended to use minimum solvent to support the goal of recovering…
Q: What type of deviation is shown by a mixture of ethanol and acetone? What type of azeotrope is…
A: Azeotrope is a mixture of two liquids having the same composition and have constant boiling points.…
Q: directly analyse a solid sample with AAS, which method will you prefer? Explain this.
A: Follow the explanation for to understand and chose the method for solid sample analysis.
Q: Three sample, X (neutral), Y (basic), and Z (acidic), were mixed and dissolved together in…
A: Dissolve the mixture in dichloromethane and separate the organic and aqueous layer using liquid…
Q: For separating the 9H-fluorene and benzophenone mixture, you used silica gel as your solid phase,…
A: Column chromatography is an analytical tool that is employed in the separation of the mixture of…
Q: Briefly describe on how peptization may occur during washing process of pure compound
A: Peptisation is the process of converting a precipitate into colliodal particles by adding an…
Q: 1. Which is a false statement regarding solid-phase synthesis?
A: A solid phase synthesis is a heterogeneous reaction technique in which a reagent reacts with the…
Q: How to prepare primary emulsion by Forbes method and why this method is called Extemporaneous?
A: Given: Emulsions and bottle forbes method To find: Primary emulsion by bottle forbes method and why…
Q: I start my day by running mixed standards using a well established method. My compounds all elute…
A: This can be explained as
Q: which would be the best extraction procedure to ensure thorough removal of a carboxylic acid…
A: When we get carboxylic acid as an by product in an organic layer ,it becomes important to remove it.
Q: Explain the function of using dichloromethane after the steam extraction of Eugenol. Also discuss if…
A: Answer - During the process, Eugenol is extracted from the distillate with dichloromethane and…
Q: What is the structure and IUPAC name of atrazine? The herbicide simazine is more polar than…
A: The structure of atrazine is as follows: The IUPAC name of atrazine is…
Q: create a separations flow chart for Sb3+, Fe3+, Zn2+, Al3+, Cd2+ without using sulfides or…
A:
Q: The following conditions may not cause tailing EXCEPT a. Volatile solvent b.Uncovered chamber…
A: TLC is one of the basic technique to get a preliminary idea about the compound synthesized in the…
Q: Compound A has a lower affinity for the stationary phase than compound B and can dissolve well in…
A: Compound A will elute first
Q: Question a) Discuss the effect of solvent polarity on Rf-values.
A: Since you have posted two questions, we will solve first question for you. Please repost other…
Q: The procedure requires the use of a 1.1 molar equivalent of benzyltriphenylphosphonium chloride…
A: Given data, Molar mass of BTPC = 388.90 g/mol Volume of benzaldehyde = 1.86 mL = 1.86cm3 Molar mass…
Q: What is a spectrophotometer used for in a cobalt chloride solution analysis
A:
Q: How is "Characterization and spectroscopic techniques for analyzing" used in a melting point…
A: Melting point is the temperature when a substance starts melting. The melting point of a compound is…
Q: Purification of benzoic acid 1. What is the purpose of washing the crystal in the filter paper with…
A: 1) Answer: Benzoic acid is prepared from toluene industrially. Toluene is react with cl2 gas under…
Q: What is the literature value of the melting range of: Crystallized acetanilide vs Crude…
A: Comparing the melting point of recrystallized acetanilide and pure acetanilide revealed little to no…
Q: Develop a numbered procedure for the fischer esterification of butyric acid and ethanol including…
A: A question based on Fischer-esterification synthesis, which is to be accomplished.
Q: 3 Draw a flow chart to shows the strategy for separation of three compounds: Phenanthrene and…
A: The three components can be separated by the principle of solubility of organic and ionic compounds.…
Q: Why is it required to add drying agent like sodium sulphate to the organic layer which may contain…
A: In an organic solution, there are often traces of water present because water is slightly soluble in…
Q: Why is there a need to add concentrated H2SO4 to the centrifugate and evaporating almost to dryness…
A: There is a need to add concentrated (H2SO4) to the centrifugate and evaporating almost to dryness…
Q: A crude nonacidic product mixture dissolved in diethyl ether contains acetic acid. Describe an…
A: We have a crude non acidic product mixture dissolved in diethyl ether contains acetic acid. We have…
Q: Come up with a description of what you would do experimentally to recrystallize any two of the…
A: Organic compounds made by using different synthesis techniques may contain impurities. Purification…
Q: Aqueous sodium bicarbonate was used to wash the crude t-pentyl chloride.a. What was the purpose of…
A: (a)
Q: If insoluble impurities, e.g., dust, tissue, filter paper, etc., were mixed with the sample, how…
A: Insoluble impurities The term "insoluble impurities" refers to contaminants that settle or float on…
Q: 1. Why does the solid need to be finely ground and then tightly packed in a melting point capillary…
A: The temperature at which the solid melts and starts converting into liquid is called as melting…
Q: Consider the mordant dyes and alizarin red S results, specifically focusing on the use of copper…
A: The substance mordant dye can be described as the dyes that will be utilized for the dyeing of the…
Q: A fractional distillation of this mixture is carried out: what is the nature of the recovered…
A: Total mass of sample = 80 g Mass of water = 60 g Mass of nitric acid = 80-60 = 20 g number of moles…
Briefly discuss how to identify the unknown compound by using mixed melting point method.
Step by step
Solved in 2 steps
- Give correct detailed Solution with explanation needed. Don't give Handwritten answer. Don't use Ai for answering thisPlease give a detailed handwritten solution.Three sample, X (neutral), Y (basic), and Z (acidic), were mixed and dissolved together in dichloromethane. Propose a method to separate all given sample individually using the combination of liquid-liquid extraction, crystallization, distillation, and sublimation technique.