Assume Vin is a 1 kHz 'sine wave'. Assume the threshold voltage of the diode is 1 V. The L78L33 is a 3.3 V Voltage regulator and requires at least 5 V on its input to be able to have a steady 3.3 Vout. D1 L78L33 2 Vin R1 Vout Given Variables Name Value Units Vin 8.5 Vrms C1 11 uF What is the smallest value resistor R1 that can be used as a load before Vout is no longer regulated at 3.3 V?

Assume Vin is a 1 kHz 'sine wave'. Assume the threshold voltage of the diode is 1 V. The L78L33 is a 3.3 V Voltage regulator and requires at least 5 V on its input to be able to have a steady 3.3 Vout. D1 L78L33 2 Vin R1 Vout Given Variables Name Value Units Vin 8.5 Vrms C1 11 uF What is the smallest value resistor R1 that can be used as a load before Vout is no longer regulated at 3.3 V?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 3 Consider the following cirucit: in + V1 R1 5 PULSE (0 2 1 1 1 1) (Note again the unrealistic diode characteristics.) The input is a ramp: 2.0V- 1.6V- 1.2V- 0.8V- 0.4V- 0.0V- 0.0s 0.2s 0.4s 0.6s 0.8s out .tran 2 .model diode D(Ron=5 Vfwd=1 Roff=1G) V(in) D1 diode 1.0s 1.2s 1.4s 1.6s 1.8s 2.0s The output voltage is similar to the input voltage, except that it breaks at a certain voltage and reaches a different final value. Find the break voltage and the final value of the output.
In the clamping circuit below, assume the diode has Von-0.7V and V₁ is a sinusoidal wave with a peak-to-peak amplitude of 10V. How much is the maximum value of the output voltage signal (Vmax)? And how much will it be if we set V₂=2V? Input V1 C1 0.1e-6 9.3 V and 7.3 V 9.3 V and 11.3 V 11.3 V and 7.3 V O 7.3 V and 12.0 V O 12.0 V and 7.3 V Output D1 1N4148 .tran 30-3 V2 0 Vmax V(output) 0.0ms putput MAN Input 0.6ms 1.2ms V(input) 1.8ms 2.4ms 3.0ms
Using an ideal diode, design a clamper circuit that result in the desired output waveform as shown in Figure Q7. Show overall analysis to justify the proposed design. 7. Vo Vi Designed Clamper Circuit - 3 V -20 - 43 V - Fiqure Q7 20
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
Q2) For the circuit shown in Figure 2, sketch the output voltage (across the load 2.2 KO resistor) and the load current (through the load 2.2 KN resistor). Sketch the diode voltage (across the diode D1) and the diode current (through the diode D1). The input Vi is sinusoidal with maximum amplitude (peak) of 14.1422 V and frequency of 60 Hz. The diode D1 is a Silicon diode. The sketches have to be at least for two cycles of the input. D1 2.2 K2 Vi
Draw output waveform for the following circuit. Suppose input is a pure square wave with a positive half at 10 V and negative half at -10 V for ideal diodes. D1 D2 220 R3 R1 1k R2 1k
3) Demonstrate clipping of negative waves with an inverted diode in the output. A circuit which removes the peak of a waveform is known as a clipper. Show a negative clipper. Produce a schematic diagram with LTspice schematic capture program. During the positive half cycle of the 5 V peak input, the diode is reversed biased. The diode does not conduct. It is as if the diode were not there. Show the positive half cycle is unchanged at the output V(2). Show the output positive peaks overlays the input sinewave V(1). Use in the LTSPICE display module, the command "plot v(1)+1)" accomplishes this. Voltage values: Resistor valuse: 1 ΚΩ DC offset: 0 V Amplitude: 5 V Freq: 1 KHz
Consider a junction diode has dc biased current at operating point ID=0.8 mA. A sinusoidal voltage is superimposed on the VD such that the peak-to-peak sinusoidal current id(t) = 0.05ID. Find the value of the applied peak-to-peak sinusoidal voltage vd(t).
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
By comparing other diodes, reverse recovery time of Schottky diode is lower. Select one: O True O False is the RMS value of output voltage of the step down chopper which is having 240 V as a input for a duty cycle of 60 %.
Make the described voltage multiplier circuit, determine the voltage charge in each capacitor, and the output voltage of the circuit. Plot the output waveform in proper phase alignment with the input voltage. Indicate the peak values with the support of your solutions. Use silicon diodes in your analysis and an input V=10 Vrms. a) Half-wave voltage doubler b.) Full-wave voltage doubler
1. The applied voltage in a Germanium diode is found to be 0.41 V with a threshold voltage of 26 mV and saturation current of 1 nA Calculate for the diode current. 2.The voltage as the switch is closed for an SCR circuit is found to be 4V and the current is 0.2A Compute for the average power conduction loss for a frequency of 60 H2 Assume the tum on and turn off time is 0.12 m and 0.25 ms respectively 3.If the trigger voltage in the circuit is replaced by SV, the series resistor by 330 ohms, compute for the gate current at the SCR when Switch 1 and 2 are momentarily switched on. The voltage at the gate to cathode is 0.7V while that of the voltage from anode to cathode is 10V 4.Id=11.84 mA n=2, and the applied bias voltage is 0.5V and the temperature requirement is at 20°C. Findthe diode saturation current 5.For a frequency of 60 Hz, compute for the average power conduction loss if the difference in the turn off and turn on time is 10 ms and the instantaneon power is given as a…