As a senior automotive engineer, you are asked to design a transmission featuring 2-speed forward ratios and 1 reverse gear that can handle an engine with the maximum torque of 50 Nm (at 3500 RPM) and the maximum speed of 5000 RPM (torque of 35 Nm). The transmission must be able to provide: - the maximum output torque of at least 120 Nm, - the maximum output speed of at least 6000 RPM.

As a senior automotive engineer, you are asked to design a transmission featuring 2-speed forward ratios and 1 reverse gear that can handle an engine with the maximum torque of 50 Nm (at 3500 RPM) and the maximum speed of 5000 RPM (torque of 35 Nm). The transmission must be able to provide: - the maximum output torque of at least 120 Nm, - the maximum output speed of at least 6000 RPM.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter47: Steering Systems

Section: Chapter Questions

Problem 4RQ: Define the term gearbox ratio.

See similar textbooks

Similar questions

480 ft-lbf First Gear (2.66) Final Drive (3.42) Figure 2 - Corvette Z06 and its transmission schematic. You start by measuring the 60-0 mph braking performance, which is accomplished along 30.56 m. The test weight (including the driver) was found to be 1510.5 kgf. Peak torque (@4800 rpm) 1st gear reduction Axle Torque Thrust Force After the braking test, you are asked to determine the maximum acceleration in the first gear. Consulting the manufacturer, you find out the following technical data: Final drive (differential) reduction Rolling radius of the rear tyres % weight on the rear tyres Table 1 - Technical data for the Corvette Z06 480 lbf-ft 2.66 3.42 0.327 m 65% 1) Assuming the maximum traction capacity of the tyres has been determined in the braking test, CALCULATE the maximum traction generated by the rear tyres in first gear. CALCULATE the available thrust force (i.e. traction) from the torque on the wheels.
The client requires a single step-up spur gearbox to transmit a 10 kW Power from a shaft rotating at 1000 rpm, while output speed must be 1700 rpm. The material of the gear and pinion 817M40 and 655M13, respectively. Use table 6.10 on page 128 to collect suitable gear and pinion. 1.1 briefly state the problem 1.2 State the design specification considering the following design factors a) Functionality b) stress 1.3 State formula and standards relevant to the single step-up spur gearbox design. 1.4 If the pinion has 24 teeth, use the Lewis formula to determine the face width of the pinion and gear. Then, do one set of the calculations and tabulate the answers. 1.5 conclusion
You have engaged in open discussion in which you have to evaluate the conditions needed for anepicyclic gear train to become a differential. Using appropriate schematic and hand sketch show how adifferential works in this application
How do gear ratios in a mechanical transmission system influence torque and speed output, and what considerations must be made when designing a multi-stage gearbox for a specific application?
Define the term gearbox ratio.
Q2/ Two mating involute spur gears of 20* pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on cach wheel is such that the path of approach and the path of recess on cach side are half the maximum possible length each, find: i) the addendum for pinion and gear wheel, ii) the length of arc of contact, iii)the maximum velocity of sliding during approach and recess. Assume pinion to be driver.
QUESTION 1 GEARS [50]The client requires a single step-up spur gearbox to transmit a 10 kW power from a shaft rotating at 1000 rpm, while the output speed must be 1700 rpm. The material for gear and pinion is 817M40 and 655M13, respectively. Use table 6.10 on page 128 to select the suitable gear and pinion.1.1 Briefly state the problem. (3)1.2 State the design specification considering the following design factors:1. Functionality2. Stress8)1.3 State formula and standards relevant to the single step-up spur gearbox design. (4)1.4 If the pinion has 20 teeth, use the Lewis formula to determine the face width of the pinion and gear. Then, do one set of calculations and tabulate the answers.(33)1.5 Conclusion. (2)
Evaluate the conditions needed for an epicyclic gear train to become a differential, and show how a differential works in this application with a single driver.
40. Calculate the final drive gear ratio for a differential using a ring gear with 49 teeth and a matching pinion gear with 15 teeth. You may use a calculator. Final gear ratio = %3D
State the formula and standards relevant to the single step-up spur gearbox of 10kW rotating at 1000rpm with output speed of 1700rpm. Its materials are pinion (665M13) and gear 817M40)
The client requires a single step-up spur gearbox to transmit a 10 kW power from a shaft rotatingat 1000 rpm, while the output speed must be 1700 rpm. The material for gear and pinion is 817M40and 655M13, respectively State formula and standards relevant to the single step-up spur gearbox design
2a-e. Outline five transmission problems its causes and their solutions.