An electric motor is"driving" a machine in a textile factory with a "flat belt". The motor is delivering 1.25 hp at 1725 rpm to the machine and the coefficient of friction between the belt and the 3.5 in diameter steel pulley attached to the motor shaft is μ = 0.25. If the tension in the "tight side" of the flat belt is 54 lb, what is the minimum "angle of wrap" needed to prevent the flat belt from slipping on the motor pulley? Ans. 151.3°
Q: The aluminum block has a rectangular cross section and is subjected to an axial compressive force of…
A: if you have any doubt comment
Q: Four 10 kg masses are being supported by an 800mm solid rod. The rod is being supported at both…
A:
Q: Machines: The mechanical press is used to crush small objects at E. If the vertical force P = 750 N…
A:
Q: Problem 9-1: An iron-constantan thermocouple is placed in a moving air stream in a duct, as shown in…
A: Step 1: Step 2: Step 3: Step 4: Step 5:
Q: Question 2: Find the centroid of area G(xg, yg), moment of inertias (Ix, ly) in the built-up…
A: The objective of the question is to find the centroid of the area and the moment of inertias for a…
Q: Are car body styles exactly identical between years? Like does a 2009 Dodge Charger look identical…
A: The question is asking whether the body styles of cars remain exactly the same between different…
Q: The wall crane supports a load of 700 lb. Determine the horizontal and vertical components of…
A: Given:The wall crane supports a load .The weight of jib ABC is .The weight of member BD is .Method…
Q: Please provide full detailed solution and explaination for this problem. Table A-20 is provided.…
A: Step 1:Given: Tension T2 is 15% of T1=> T(2) = 0.15T(1)Step 2:Now, let us apply the summation of…
Q: sion force T is attached to a horiz ber at B and C to support a sign st passes over a small…
A: The stress-strain relationship for the wire ishere, is the strainThere are different values of the…
Q: Pravinbhai
A: The objective of this question is to determine the slope at the end B of the beam and the…
Q: Parvinbhai
A: The objective of this problem is to draw the shear force and bending moment diagrams for a car jack…
Q: What is the purpose of of the viscous clutch?a. to engage engine otrque to the transmission.b. to…
A: The correct option is: b. to improve mobility when driving conditions become difficult Explanation:…
Q: PROBLEM 5: The upper block is attached to the ground as shown in the figure by a short rope. The…
A: The objective of this question is to determine the tension in the rope, the friction force under the…
Q: Q\1 Sketch root locus for the systems below, find k-range for stability, sd. and k at zeta 0.5. k 1.…
A:
Q: Explain, with help of a sketch, the following gear tooth nomenclature:Addendum Dedundum Face width…
A: Sketches of the Gear Tooth Nomenclature The gear tooth nomenclature describes the various…
Q: Question: a student has chosen the particular weight of 1.373 kg for gear and optimised is by…
A: Based on the plot, it appears that a total contact ratio of around 1.2 provides the lowest contact…
Q: Pravinbhai
A: Kindly refer to the attached photos. Thank you!
Q: 5. Determine la reacción en los apoyos A y F. Las fuerzas verticales representan el peso de la…
A: Given:Required: -Reactions at supports A and F Solution: Step 1: Find the distances/length of the…
Q: Which of the following shifts can be performed on the fly? a.from four low to four high b)from four…
A: Shifts can be performed on the fly is from four high to four low. This is because In order to do…
Q: Which stress theory gives a more conservative result? Select one: ○ a. von Mises. O b. The result…
A: a. von Mises: This option is incorrect because it doesn't account for variations in stress state,…
Q: CONSIDER AM DBJECT COMPOSED OF TWO SMALL METAL PALLETS LOCATED IN (x;Y) = (2:0) AMD (2;2) AND A…
A: (A) The object can be sketched as follows:sketch of the…
Q: Determine the amount of acres of land necessary to generate 50 MW of solar power at noon in…
A: Step 1: Convert the power output to watts:50 MW = 50,000,000 watts Step 2: Given that the solar…
Q: Please do not rely too much on chatgpt, because its answer may be wrong. Please consider it…
A: For instance a vertical pipe filled with liquid. We want to find the pressure at a specific point…
Q: Please answer all parts
A: Step 1: Step 2:Step 3: Step 4:
Q: ___________ occurs mainly on the rake face of cutting tool. Group of answer choices Flank wear…
A: The question is asking about the type of wear that primarily occurs on the rake face of a cutting…
Q: Learning Goal: To use transformation equations to calculate the plane state of stress in a rotated…
A: Step 1:Given ∣σx∣=40Mps ∣σy∣=58Mps σy=−58Mps ∣τxy∣=8Mpa τxy=−8Mpa θ=40∘ Step…
Q: how does your computations go when for example all needed info are derived as usual and THE PIPE…
A: Introduction-Fluid movement occurs often during solidification, interfering with the previously…
Q: Question 2. Consider the beam with a I-beam cross section in Figure 2. Consider point A at the…
A:
Q: Show that Eq. implies that the rates of strain tensor is symmetric. Ow ди Ένα E ax ay' Öz ди ar +…
A:
Q: Your answer is partially correct. A laser emits 4.07 × 1019 photons per second in a beam of light…
A: Step 1: Step 2: Step 3: Step 4:
Q: . An object of mass 12 kg is suspended from a pulley which has a mass of 6 kg and a radius of…
A: Given, mass of object is 12 kg Mass of pulley is 6 kg Resisting moment is 2N.m Rotating radius of…
Q: DONT USE AI!!
A: The Slope-Deflection Method and the Stiffness Matrix Method, considering the constant bending…
Q: s 2a
A:
Q: Define the sideslip angle at the centre of gravity of a car. Then show that v+raj B11 = u-rt1/2…
A: Sideslip angle:The difference between the two directions of a vehicle moving and the direction the…
Q: Please solve step by step , Don't use any Ai
A: Step 1: Step 2: Step 3: Step 4:
Q: A Consider the system shown below, consisting of a spring connected to a clamped-free bar. The bar…
A:
Q: Needs Complete solution don't use chat gpt or ai i definitely upvote you. Be careful Downvote…
A:
Q: A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and…
A: The radius of gear A is The initial angular speed of gear A is The final angular speed of gear A is…
Q: 110% 72 Sketh the following wavefroms: a)60sin(w+0°) b)2 cos(wt+20°) c)-30sin(wt+3°)
A: Step 1: lets first understand the graph axiswe are referring waveform in sin, we will convert cos…
Q: Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are…
A:
Q: A point load of 2.236kN is applied at point 3 of a frictionless pin- jointed structure which…
A: Member - 1:Member-1 connects nodes 1 and 2. Consider the displacements of node-1 along x and y…
Q: 2.10. Compute the long-term average throughput, cycle time and x-factors for this factory for fixed…
A: The given factory uses a serial flow paradigm, in which components pass sequentially through four…
Q: Learning Goal: To determine the principal stresses that act on an element and to construct Mohr's…
A: Step 1:the principal stress varies from 3d to 2d state as we we are applying additional stress in…
Q: . Problem 9-4: The pressure fluctuations in a pipe filled with air at 20°C at about 1 atm is to be…
A: Step 1:To solve this problem, we'll first calculate the resonance frequency of the system using the…
Q: فقرة Q3 Find the phase relationship for the following waveforms,also sketh. a)v = 5sin(wt-70°),i=sin…
A: (a)Sketch: Compute V and I at different value of time with interval of 30o let omega = 1tV = 5…
Q: Explain, with sketches, a speed reduction of 7.5:1 using (a) Simple gear train and (b) Compound gear…
A: Given:To find:Explain, with sketches, a speed reduction of 7.5:1 usingSimple gear train and Compound…
Q: (b) When the silicon is in a certain position, the probe is 3.5 mm from it. The silicon must remain…
A:
Q: Q1. Describe the following modes of failure associated with gear teeth, indicating their causes and…
A: Details about the prevention of1) tooth breakage of gear and 2) surface damage of teeth
Q: . An object of mass 12 kg is suspended from a pulley which has a mass of 6 kg and a radius of…
A: I can analyze the question and provide a general solution approach, but I cannot access specific…
Q: 1. A rod made from a material with a constitutive law of the form σ = 100 + 75€ 0.2 is drawn from a…
A:
solve show solution
Step by step
Solved in 2 steps with 2 images
- Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
- An object weighing 400 N is held by a rope that passes over a horizontal drum. The coefficient of friction between the rope and the drum is 0.25. If the angle of contact is 150 degrees, determine the force that will raise the object.A horse is tied to a horizontal pole using a rope. The rope is only wrapped around the pole without any knots. Free hanging part of the rope weighs 0.032 N. If the horse can exert a maximum of 746 N, what is the minimum number of turns of the rope required to prevent the horse from escaping? The coefficient of friction between the rope and the pole is 0.4.A belt drive is required to transmit 12 kW power. The velocity of the belt is 9.6 m/sec. If coefficient of friction is 0.25 and the angle of contact is 150º, determine the maximum tension is the belt.
- Q1: - The block shown in figure below has a mass of 100 kg and is resting on 30° inclined surface. The block is connected to another block with a weight of W through a light and inextensible cord that is passing around a frictionless pully. The coefficient of static friction between the 100 kg block and the inclined surface is 0.45. Determine the minimum and maximum weights of the second block that keep the system in equilibrium. Also, show whether the impending motion is by slipping or by tipping. -300 mm- 100 kg 450 mm 600 mm-.A belt 200 mm wide and 7 mm thick drives a pulley at belt speed of 25 m/s. The density of the belt is 980 kg/m3 and the coefficient of friction between the belt and pulley is 0.23. Given that the angle of contact of pulley is 2π/3 and the allowable stress of the belt is 1.8 MPa, determine the tension on the slack side of the belt (T2) in NA 150lb man stands on a 60lb bar to which a cable is fixed at B. The cable passes over two fixed pegs with coefficients of friction indicated. Assume that the arrangement of the pegs permits the cable to contact each peg over a total angle of 90-degrees (90-degrees per peg). Assume that the normal force exerted by the man on the bar acts downward through A. Find the largest force the man can exert on the cable and maintain the bar horizontal.
- body resting on a rough horizontal plane requires a pull of 300 N inclined at 40º to the horizontal plane just to move it. It is found that a push of 150 N inclined at 40o to the x-axis can also make the body to move. Determine the weight of the body and the coefficient of friction.The belt drive in which pulleys rotate in the same direction is used to transfer power. The pulley diameters are 1.74m and 0.833m and it connects two parallel shafts which are 3.25m apart. The initial tension in the belt when it is stationary is 4500N. The smaller pulley is rotating at 710 rpm and coefficient of friction between the belt and pulley is 0.29. Determine the power transmitted by the belt driveA uniform ladder of length 3.25 m and weighing 250 N is placed Against a smooth vertical wall with its lower end 1.25 m from theWall. The coefficient of friction between the ladder and floor is0.3. The frictional force acting on the ladder at the point of contactWith floor is O 70 O 68 O 65 O 79 O 75 N.