An eccentric load of 66 kN is acting as shown in the figure 6.5. Using elastic method, compute for the maximum force on the most stressed rivet. 2 Using the reduced eccentricity method, compute for the maximum force on the most stressed rivet Using ultimate strength method, compute for the max. force on the most stressed rivet. 100 100 e-200 900 75:75 Figure 6.5 P-66 KN

An eccentric load of 66 kN is acting as shown in the figure 6.5. Using elastic method, compute for the maximum force on the most stressed rivet. 2 Using the reduced eccentricity method, compute for the maximum force on the most stressed rivet Using ultimate strength method, compute for the max. force on the most stressed rivet. 100 100 e-200 900 75:75 Figure 6.5 P-66 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 inch and the working stresses listed in the table are not to be exceeded. Steel 2 ft Bronze 4 ft Aluminum 3 ft 2P 3P 4P A (in.?) E (psi) a. (psi) Steel 0.75 30 x 10 20000 12 x 10 10 x 10 Bronze 1.00 18000 Aluminum 0.50 12000
A beam carrying an allowable actual moment of -38 KN- m is reinforced as shown. If the the concrete is normal weight and f'c = 25MPa and fy = 420MPa. Determine the following: a. The cracking moment of the beam. b. The transformed moment of Inertia. c. The actual tension steel stress. d. Check the stress if it is correct by force checks. mm www.009 4-020 О 140 mm 300 mm 170 mm * 170 mm: ww.08 ✓ 60 mm
S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.
A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below.The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm.Parameter Description Value UnitsL - Beam length 250 mma - Width of the flange 80 mmd - Height of the web 75 mmσ - Yield stress 250 MPaYou are tasked with ensuring the beam can withstand the applied loading. To do this you must:a) Calculate the centroid for the given cross-section. Your value of ?ത should be measured fromthe bottom of the section. Determine an expression for Q (statical moment of area) for thegiven shape. The expression(s) for Q should be in terms of the variable, y, measured from thebottom of the section. b) Create a graph of the shear and bending stresses at the fixed support (B) over the crosssection. The stresses should be plotted as a function of y, measured from the bottom of thesection.
A) Determine the shape factor and the Fully Plastic Moment (Mp) for the shaded symmetrical hollow rectangular beam section shown below. Assume the yield stress Oy =275 N/mm?. B) If two plates of width 250 mm and thickness equal to 't' mm is connected (fabricated) at top and bottom (one plate on each side) for the given section, then what is the improvement in the fully plastic moment(Mp) of the section. C) If this revised fabricated section is now rotated by 90 degrees, what is its effect on the shape factor of the section? 200 mm. -50 mt 100 mm 400 50m Note : Take the value the 't' as equal to the last two digits of your student id. If the last wo digits are zero then takes T=10mm ww 00T
A steel bracket of solid circular crosssection is subjected to two loads, each of which isP = 4.5 kN at D (see figure). Let the dimension variablebe b = 240 mm.(a) Find the minimum permissible diameter dminof the bracket if the allowable normal stress is110 MPa.(b) Repeat part (a), including the weight ofthe bracket. The weight density of steel is77.0 kN/m3.
A bracket has been loaded as shown in figure. Compute the top and bottom fibre stress at section А-B. A 200 mm 200 mm Section AB 500 mm 1000 kN 2000 mm k-500 mm>
pls help ASAP absolute value of torential sheer stress of the hollow steel Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). 8o N-m Sm steel Iel tiraler dhmmum Selid circalor D= 75 my D 8o mm G GA G 1S0 EP
Which of the following is an allowable stress design concept. O Alternate Basic Load Combinations O OMn O 1.2D+1.6L O Rn = FyAg
Time left 0:16:22 (CLO 1, 2)Determine the stress in the Aluminum rod (Psi) after the load 142 (kips) is applied. The light rigid bar ABCD is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free. Steel L = 3 ft A = 0.5 in? E = 29 x 10° psi 4 ft - Aluminum P. 2 ft 2 ft-> L= 4 ft A = 0.75 in? E = 10 x 10° psi %3D
Q1: A simply supported reinforced concrete beam has a cross-section as shown in the Figure 1. Using Working Stress Method to calculate maximum load (wmax.). (Neglect self-weight), use f'c=21 MPa and fy=420 MPa Wm max 4Ø 25 6 m- 2 m - 300 mm- Figure 1 -537 mm- -ww 009
Q1: A simply supported reinforced concrete beam has a cross-section as shown in the Figure 1. Using Working Stress Method to calculate maximum load (wmax.). (Neglect self-weight), use f'c=21 MPa and fy=420 MPa W max 4Ø 25 6 m- 2 m- - 300 mm- Figure 1 -537 mm- -ww 009