A4-pole series motor has 944 wave-connected armature conductors. the flux per pole is 34.6 m Wb and the total torque developed is 209 N-m. applied voltage of 500V,Total motor resistance is 3 ohm. Calculate 1-The line current taken by the motor.2-The speed at which it will run, 3-The total copper losses, 4- The input power.?

A4-pole series motor has 944 wave-connected armature conductors. the flux per pole is 34.6 m Wb and the total torque developed is 209 N-m. applied voltage of 500V,Total motor resistance is 3 ohm. Calculate 1-The line current taken by the motor.2-The speed at which it will run, 3-The total copper losses, 4- The input power.?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter33: Single-phase Motors

Section: Chapter Questions

Problem 32RQ

See similar textbooks

Similar questions

A 6-pole series motor takes 40 A from the supply mains at 220 V. It has 600 lap-wound conductors. The series field resistance and armature resistance are 0.01 ohms and 0.09 ohms respectively. Flux per pole is 29 mWb. Calculate armature torque (Nm).
4-pole DC in series motor, 180 Nm torque. The coil is wavy, at 600 total conductors, and the magnetic flux per electrode is 0.02 Weber. The resistance of the product and log windings is 0.2 ohm and 0.1 ohm, respectively. Calculate the copper knob if the reciprocating force generated is 205 volts
(B)-ndicate whether the following statements are true or false and correct the faise statements. -When a series d.c. motor is operate without load, the armature will not run. The strength of magnetic field in d.c. shunt generator can be varied by varying the polarity of the field poles The main disadvantage of series generators is Output voltage varies as the Toad varies There is no output from the transformer under short-circuit conditions
A DC shunt generator delivers 45 A at a terminal voltage of 220 V. The armature and the shunt field resistances are 0.01 2 and 44N respectively. The stray losses are 375 W. What is percentage efficiency of the DC generator
1. The operation of Commutator in DC Motor is * O a) to convert dc to ac O b) to convert ac to dc O c) to convert fixed dc to variable dc O reverse the current direction in the rotating windings each half turn
H.W 1) A 4-pole, 500 V d.c. shunt motor has 720 wave-connected conductors on its armature. The full-load armature current is 60 A and the flux per pole 0.03 Wb. The armature resistacne is 1.2 Q and the contact drop is 1 V per brush. Calculate the full-load speed of the motor. H.W 2) A d.c. series motor with series field, and armature resistance of 0.06 ohm and 0.04 ohm respectively is connected across 220 V mains. The armature takes 40 A, and its speed is 900 rpm. Determine its speed when the armature takes 75 A, and excitation is increased by 15% due to saturation.
2. A 4 pole machine running at 1500 rpm has an armature with 90 slots and 6 conductor per slot. The flux per pole is 10mWb. Determine the terminalemf as DC generator if the coils are lap connected. If the current per conductor is 100A, determine the electrical power.
A 110 V, 60 Hz, 6 – pole single phase induction motor 1/3 hp has the following equivalent circuit impedances: RI = 1.52 ohm, R2 = 3.13 ohm and x1 =2.10 ohm, x2 =1.56 ohm. Xm=58.2 ohm, The Friction, windage and stry losses =16W, the core loss = 35 W, For a slip of 0.05, calculation (a) input current, (b) power factor, (c) developed power, (d) output power, (e) speed (f) in put power (g) air gab power (h) T ind (i) T load 6) efficiency.
The DC shunt generator with the terminal voltage 350 V, armature drop 7 V and the each brush drop 2 V, then the value of generated emf is
At rated voltage, a 125 kw, 300-V long shunt compound system provides power with a stray power loss of 3.69 kW. The winding resistors are as follows: armature=0.023, series field=0.04, shunt field=75. Under this condition, find the efficiency of the system.
A 4-pole series motor has 944 wave- connected armature conductors. the flux per pole is 34.6 m Wb and the total torque developed is 209. N-m..applied voltage of 500V,Total motor resistance is 3 ohm. Calculate -The line current taken by the motor.2-The speed at which it will run, 3-The total copper losses, 4- The input power.
A dc generator is run at 500 rpm. The eddy current losses and hysteresis losses are found to be 100 and 200 W, respectively. At what speed will it be run to reduce the core losses by 20%?