A36 steel is used for the tension member shown in Figure a. Determine the nominal strength, in kN based on the gross area. b. Calculate the value of the effective net area in square MM. C. Determine the nominal strength based on the net area. - PL 16MMX300MM |5Q4.75175,175,175.J25. 50 100 100 50

A36 steel is used for the tension member shown in Figure a. Determine the nominal strength, in kN based on the gross area. b. Calculate the value of the effective net area in square MM. C. Determine the nominal strength based on the net area. - PL 16MMX300MM |5Q4.75175,175,175.J25. 50 100 100 50

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.
Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The bolts are 3/4 in. diameter. The steel is A572 Gr. 50. Check yielding and fracture. Check Block Shear. T 3in. 73im 13in 1 3in t
A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 2-inch-diameter bolts. Assume that A₂ = 0.75An. Ae 1 2 Determine the design tensile strength for LRFD. Determine the allowable strength for ASD. CIVIL ENGINEERING - STEEL DESIGN AL Section 2L5 x 3 x 516 LLBB
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the critical net area of the connection shown. Determine the design tensile strength of the section based on yielding of the gross area.
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shear
Topic:Bolted Steel Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of bolt = 20 mm Both the tension member and the gusset plate are of A 36 steel. Fy = 248 MPa, FU = 400 MPa. Shear stress of bolt Fnv = 300MPa. Questions: a.Determine the shear strength of the connection. b.Determine the bearing strength of the connection. c. Determine the block shear strength of the connection.
The vertical member shown in Figure STCN17.02 consist of two angles welded to the 8-mm thick gusset plate. Given the following data: Angle size: 75 mm x 50 mm x 6 mm (long legs back-to-back) Area of one angle = 738 mm Size of weld = 6 mm Yield strength of steel, Fy = 248 MPa Allowable weld shear stress, F, = 124 MPa a = 25 mm a. Determine the safe capacity of the vertical member in kN. b. If P= 185 kN, determine the length of weld L2 (mm) such that each weld have equal shear stress. Neglect end returns. c. If L1 = 140 mm and L2 = 70 mm, determine the safe load P (kN) based on weld capacity assuming all welds have equal stress. AP L1 L2
3. A plate with width of 300mm and thickness of 20mm is to be connected to two plates of the same width with half the thickness by 24mm diameter bolts, as shown. The rivet holes have a diameter of 2mm larger than the rivet diameter. The plate is A36 steel with yield strength F,-248MPa and ultimate strength F,-400MPa. a. Determine the design strength of the section. b. Determine the allowable strength of the section 24mm 30mm
QUESTION 8 3. check the capacity of the shear connection. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi effective bolt hole diameter = bolt hole + 1/16" beam properties: tw=0.295 in. Fexx=70ksi what is the shear yielding capacity of shear plate in kips? (2 decimal places)
PROBLEM NO. 2: Two plates each with thickness t = 16mm are bolted together with 6-22mm diameter bolts forming a lap connection. Bolt Spacing are as follows: S₁ = 40mm, S₂ = 80mm, S3 = 100mm. Bolt diameter = 22mm. Use A36 steel. Calculate the allowable strength due to block shear only. I= 16 mm S₁ S₂ S₂ S1 40 80 80 40 18-16mm S-40 S₁-100 S-40